Using Problem 1, Please prove Number 2 and 3, the answers are already given M and B. please only solve for 2 and 3. Thank you 1. The shaft rotating at 550 rpm carries a spur gear B having 96 teeth with a diametral pitch of 6and a V-belt sheave with pitch diameter of 10 in. The teeth are of the 20°, full-depth, involuteform. The gear receives 30 hp from a pinion directly above it. Compute the torque deliveredto the shaft and the tangential and radial forces exerted on the shaft by the gear.TB = 3437.75 in-lb, W₁ = 429.72 lb, W, = 156.4 lb(a) Pictorial view of assemblyGear Q00-10.00-6.00- Gear B-V-belt sheaveSection B-BSection A-A(b) Detailed views of assembly and its components2. Problem 1 - determine the maximum moment of the assembly. Hint: Obtain the moments forvertical and horizontal planes, then compute for the resultant moments.M = Mc = 6187.86 in-lb.3. Problem 1 - If one of the bearings is located at the left of C whose bearing seat is made withsmall fillet (K₁ = 2.5) and the shaft material is AISI B1113 (k) cold finished, determine the shaftdiameter. Use a size factor of 0.8 and reliability of 99%. Design factor N is 3.D = 3.0 in.

Since you have asked multiple questions, we will solve the first question for you. If you want any…

Answered: Problem 1-determine the maximum moment…

Problem 1-determine the maximum moment of the assembly. Hint: Obtain the moments for vertical and horizontal planes, then compute for the resultant moments. M = Mc = 6187.86 in-lb.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A Coniflex, straight-tooth bevel gearset is supported on shafts with centerlines intersecting at a 90° angle. The gear is straddle mounted between closely positioned bearings, and the pinion overhangs its support bearing. The 15-tooth pinion rotates at 900 rpm, driving the 60-tooth gear, which has a di- ametral pitch of 6, pressure angle of 20°, and face width of 1.25 inches. The material for both gears is through-hardened Grade I steel with a hardness of BHN 300 (see Figure). It is desired to have a reliability of 90 percent, a design life of 10° cy- cles, and a governing safety factor of 2.5. Estimate the maximum horsepower that can be transmitted by this gear re- ducer while meeting all of the design specifications given.
A spur pinion of pitch diameter 50 mm rotates at 200 rad/s and transmits 3 kW power. The pressure angle of the tooth of the pinion is 20° Assuming that only one pair of the teeth is in contact the total force (in Newton) exerted by a tooth of the pinion on the tooth on a mating gear is...
A 220 mm diameter of 14.5 degrees involute gear is used to transmit 50 kW at 580 rpm Find the total force transmitted on the gear.
A straight gear with module m = 5 mm and face width bw = 40 mm has center distance cd = 0.1875m. The pinion has 25 teeth, the speed is 1000 rpm, and pressure angle ᶲ = 200. Find the Hertzian contact stress at the pitch point when the gear transmits 10 kW. Neglect friction forces. The gear steel has modulus of elasticity E = 207 GPa and a Poisson’s ratio of 0.30.
A compound shaft drives three gears, as shown. Segments (1) and (2) of the compound shaft are hollow bronze [G = 6,500 ksi] tubes, which have an outside diameter of 2.40 in. and a wall thickness of 0.1375 in. Segments (3) and (4) are solid 1.00-in.-diameter steel [G = 11,500 ksi] shafts. The shaft lengths are L1 = 58 in., L2 = 16 in., L3 = 16 in., and L4 = 28 in. The torques applied to the shafts have magnitudes of TB = 970 lb·ft, TD = 430 lb·ft, and TE = 170 lb·ft, acting in the directions shown. The bearings shown allow the shaft to turn freely. Using the sign convention presented in Section 6.6., calculate: (a) the magnitude of the maximum shear stress in the compound shaft. (b) the rotation angle of flange C with respect to flange A. (c) the rotation angle of gear E with respect to flange A.
A 2 in diameter shaft uses a straight spline with seven splines and contact length of 1.5 in. Assuming it is designed to slide while under load, compute it torques transmission capacity at 100 rpm if h is 8% of that shaft diameter. Note S = 1200 psi.
A truck equipped with a 50 HP engine uses a roller chain as the final drive to the rear axle. The driving sprocket runs at 225 rpm with a center distance of approximately 500 fpm. The transmission efficiency between the engine and the driving sprocket is 85%. 1.1 Determine the pitch and width of chain to be used. 1.2 Determine the number of teeth in each sprocket and the pitch diameters.
simple gear train of 30 and 50 teeth for pinion and gear wheel respectively, is used to drive an electric wheelchair at a velocity that is double the maximum velocity of slip. The pinion has an equal addendum as the gear wheel, a module of 3 mm, and a pressure angle of 14.5o. The wheelchair has a maximum velocity of 5 m/s when its pinion rotates at 800 r.p.m. Calculate: 1. The magnitude of the velocity of slip of gears in mesh.2. The angular speed of the gear wheel in rad/s.3. The maximum length of a path of the approach in mm.
2. A shaft is supported on bearings A and B, 800 mm between centres. A 20 degrees straight tooth spur gear having 600 mm pitch diameter, is located 200 mm to the right of the left hand bearing A, and a 700 mm diameter pulley is mounted 250 mm towards the left of bearing B. The gear is driven by a pinion with a downward tangential force while the pulley drives a horizontal belt having 180 degrees angle of wrap. The pulley also serves as a flywheel and weighs 2000 N. The maximum belt tension is 3000 N and the tension ratio is 3: 1. Determine the maximum bending moment and the necessary shaft diameter if the allowable shear stress of the material is 40 MPa.
Two parallel shafts have an angular velocity ratio of 4 to 1 are connected by gears, the largest of which has 40 teeth. Find the number of teeth of smaller gear.
A similar pair of helical gears , also on parallel axes, are to have involute teeth, of 20o normal pressure angle, and 3 mm normal module. The wheels are to have 26 and 34 teeth, and to work with a centre distance of 146 mm. Calculate the transverse pressure angle in degrees.
A helical cast steel gear with 30o helix angle has to transmit 35 kW at 2000 rpm. If the gears has 25 teeth, find the necessary module, pitch diameters and face width for 20o full depth involute teeth. The static stress for cast steel may be taken as 100 MPa. The face width may be taken as 3 times to normal pitch. The tooth form factor is given by the expression y'= 0.154-0.912/TE, where TE represents the equivalent number of teeth. the velocity factor is given by Cv=6/(6+v), where v is the peripheral speed of the gear in m/s.