Please help question 2 fen4.42. A simple three-phase power system is shown in the figure below. Assume that theratings of the various devices in this system are as follows:Generator G1 : 250 MVA, 13.8 kV, R = 0.1 pu, X = 1.0 pu.Generator G2 : 500 MVA, 20.0 kV, R = 0.1 pu, X =1.2 pu.Generator G3: 250 MVA, 13.8 kV, R = 0.15 pu, X = 1.0 pu.Transformer T1 : 250 MVA, 13.8/240 kV, R = 0.01 pu, X = 0.10 pu.Transformer T2: 500 MVA, 20.0/240 kV, R = 0.01 pu, X = 0.08 pu.Transformer T3: 250 MVA, 13.8/240 kV, R = 0.01 pu, X = 0.10 pu.Each Line: R= 82, X = 40 S.Region IGTORegion 4T₁Region 2머DXofYARegion 3YConvert this power system to per-unit on a base of 500 MVA at 20 kV at generator G2and draw the per-unit per-phase equivalent circuit of this system.

Ratings of devices as,Generator G1: 250 MVA, 13.8 kV. R-0.1 pu, X-1.0 pu.Generator 62: 500 MVA, 20.0…

2. A simple three-phase power system is shown in the figure below. Assume that the ratings of the various devices in this system are as follows: Generator Gl: 250 MVA, 13.8 kV, R=0.1 pu, X = 1.0 pu. Generator G2: 500 MVA, 20.0 kV, R=0.1 pu, X-1.2 pu. Generator G3: 250 MVA, 13.8 kV, R = 0.15 pu, X = 1.0 pu. Transformer TI: 250 MVA, 13.8/240 kV, R = 0.01 pu, X = 0.10 pu. Transformer T2: 500 MVA, 20.0/240 kV, R = 0.01 pu, X = 0.08 pu. Transformer T3: 250 MVA, 13.8/240 kV, R = 0.01 pu, X = 0.10 pu. Each Line: R = 82, X = 40 2. Region 1 0 roto Region 4 O Region 2 Ⓡ Cook T₂ Region 3 YA G₂ 00 G₂ Convert this power system to per-unit on a base of 500 MVA at 20 kV at generator G2 and draw the per-unit per-phase equivalent circuit of this system.

2. A simple three-phase power system is shown in the figure below. Assume that the ratings of the various devices in this system are as follows: Generator Gl: 250 MVA, 13.8 kV, R=0.1 pu, X = 1.0 pu. Generator G2: 500 MVA, 20.0 kV, R=0.1 pu, X-1.2 pu. Generator G3: 250 MVA, 13.8 kV, R = 0.15 pu, X = 1.0 pu. Transformer TI: 250 MVA, 13.8/240 kV, R = 0.01 pu, X = 0.10 pu. Transformer T2: 500 MVA, 20.0/240 kV, R = 0.01 pu, X = 0.08 pu. Transformer T3: 250 MVA, 13.8/240 kV, R = 0.01 pu, X = 0.10 pu. Each Line: R = 82, X = 40 2. Region 1 0 roto Region 4 O Region 2 Ⓡ Cook T₂ Region 3 YA G₂ 00 G₂ Convert this power system to per-unit on a base of 500 MVA at 20 kV at generator G2 and draw the per-unit per-phase equivalent circuit of this system.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.31P: Figure 4.37 shows the conductor configuration of a three-phase transmission line and a telephone...

See similar textbooks

Similar questions

Transmission and distribution lines are important components of any power system study. Aluminium cable steel reinforced (ACSR) (with steel in the centre – as shown in Figure Q1 is normally chosen instead of copper for transmission Explain: (a)The choice of aluminium instead of copper (b)The need to use and place steel at the core
What is load shedding, and why is it used in power systems? Explain the strategies and techniques for load shedding.
Figure 4.37 shows the conductor configuration of a three-phase transmission line and a telephone line supported on the same towers. The power line carries a balanced current of 250 A/phase at 60 Hz, while the telephone line is directly located below phase b Assume balanced three-phase currents in the power line. Calculate the voltage per kilometer induced in the telephone line.
Explain the significance of power transmission and distribution in the electrical grid, and the challenges associated with high-voltage transmission.
Why do we apply reduction factors in the design of electric equipment? Also, why do we increase the amperage for continuous loads?
Discuss the concept of load shedding and its purpose in a power system.
Electric Machine-check image, all question there. Consider the above equivalent circuit of IM, A six pole, 250 volt(line to line), 60Hz, Y connected , three phase IM has the following parameters on a per phase basis: R1=0.125Ω , R2=0.45 Ω, X1=0.5 Ω, X2=0.75 Ω, Xm=50 Ω, Rc=225 Ω The friction and windage loss is 115 W. Determine the following at its rated slip of 1.5% a)Excitation Circuit b)Power developed by motor(Pd) c)Shaft Power(Pshaft) d)Shaft Torque(Tshaft) e)Efficiency
Electric Machine - Check image, all question there. Consider the above equivalent circuit of IM, A six pole, 250 volt(line to line), 60Hz, Y connected , three phase IM has the following parameters on a per phase basis: R1=0.125Ω , R2=0.45 Ω, X1=0.5 Ω, X2=0.75 Ω, Xm=50 Ω, Rc=225 Ω The friction and windage loss is 115 W. Determine the following at its rated slip of 1.5% a)Excitation Circuit b)Power developed by motor c)Shaft Power(Pshaft) d)Shaft Torque(Tshaft) e)Efficiency
A three phase,Y connected, 215 V (line to line), 7.5 kW, 60 Hz, three pole IM has the following parameter values in Ohm/phase referred to the statorR₁ = 0.294 Ohm, R₂ = 0.144 Ohm, X₁ = 0.203 Ohm, X₂ = 0.409 Ohm, Xm = 10.25 Ohm.The total friction,windage and core losses may be assumed to be constant at 350 W independent of load. For a slip s = 0.02, compute the followingsa) Stator Currentb) Power Factor(pf)c) Rotor Speedd) Power Output(Shaft)e) Output(Shaft) Torquef) Efficiency(n)
What are the advantage of using large hydro dams over runoff the river systems in generating electricity. discuss at least three advantages.
What are the different types of power losses that occur in a power system, and how can they be minimized?
1. With an elegant diagram, discuss the three-phase power measurement using the three-watt meter method and write down the flaws in this method.