2. A three phase 370 km line (long line) has the line constant per phase: z= 0.0996 + j(0.5143+0.002 Row#) 0/km y= j(3.172+0.002*Row#) x 106 S/km If the sending voltage is 137.86/_27.770 kv (line-neutral) and receiving end voltage is 124.13 /_00 kV (line-neutral), determine the following: a) Receiving end current, IR b) Sending end current, Is c) The percent voltage regulation, VR%

2. A three phase 370 km line (long line) has the line constant per phase: z= 0.0996 + j(0.5143+0.002 Row#) 0/km y= j(3.172+0.002*Row#) x 106 S/km If the sending voltage is 137.86/_27.770 kv (line-neutral) and receiving end voltage is 124.13 /_00 kV (line-neutral), determine the following: a) Receiving end current, IR b) Sending end current, Is c) The percent voltage regulation, VR%

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter5: Transmission Lines: Steady-state Operation

Section: Chapter Questions

Problem 5.25P

See similar textbooks

Similar questions

Consider a long radial line terminated in its characteristic impedance Zc. Determine the following: (a) V1/I1, known as the driving point impedance. (b) | V2 |/V1|, known as the voltage gain, in terms of al. (c) | I2 |/| I1 |, known as the current gain, in terms of al. (d) The complex power gain, S21/S12, in terms of al. (e) The real power efficiency, (P21/P12)=, terms of al. Note: 1 refers to sending end and 2 refers to receiving end. (S21) is the complex power received at 2; S12 is sent from 1.
A 40-km, 220-kV, 60-Hz, three-phase overhead transmission line has a per-phase resistance of 0.15/km, a per-phase inductance of 1.3263 mH/km, and negligible shunt capacitance. Using the short line model, find the sending-end voltage, voltage regulation, sending-end power, and transmission line efficiency when the line is supplying a three-phase load of (a) 381 MVA at 0.8 power factor lagging and at 220 kV and (b) 381 MVA at 0.8 power factor leading and at 220 kV.
If the per-phase line loss in a 70-km-long transmission line is not to exceed 65 kW while it is delivering 100 A per phase, compute the required conductor diameter if the resistivity of the conductor material is 1.72108-m.
The 100-km, 230-kV, 60-Hz, three-phase line in Problems 4.18 and 4.39 delivers 300 M VA at 218 kv to the receiving end at full load. Using the nominal circuit, calculate the ABCD parameters, sending-end voltage, and percent voltage regulation when the receiving-end power factor is (a) 0.9 lagging, (b) unity, and (c) 0.9 leading. Assume a 50C conductor temperature to determine the resistance of this line.
The 500-kV, 60-Hz, three-phase line in Problems 4.20 and 4.41 has a 300-km length. Calculate: (a) Zc, (b) (l), and (c) the exact ABCD parameters for this line. Assume a 50C conductor temperature.
Rated line voltage is applied to the sending end of the line in Problem 5.26. Calculate the receiving-end voltage when the receiving end is terminated by (a) an open circuit, (b) the surge impedance of the line, and (c) one-half of the Surge impedance. (d) Also calculate the theoretical maximum real power that the line can deliver when rated voltage is applied to both ends of the line.
A 3 phase, 50 Hz, 150 km line has a resistance, inductive reactance and capacitive shunt admittance of 0.1Ω, 0.5Ω, and 3 x 10-6 S per km per phase. If the line delivers 50 MW at 110 kV and 0.8 pf lagging, Using nominal "T" method, determine: a. Sending end current b. Line value of the sending end voltage c. Transmission efficiency d. Voltage regulation e. Sending end power factor
A 3 phase, 50 Hz, 150 km line has a resistance, inductive reactance and capacitive shunt admittance of 0.1Ω, 0.5Ω, and 3 x 106 S per km per phase. If the line delivers 50MW at 110kV and 0.8 pf lagging, Assume a nominal phi circuit for the line determine: a. Sending end current b. Line value of the sending end voltage c. Transmission efficiency d. Voltage regulation e. Sending end power factor
In three-phase short transmission line with end-of-line interphase voltage UR = 31,5kV , from the end of the line active power absorbed PR = 9000 kW, end of line power factor is cosφ = 0,70 (end) and the length of the line is l = 20km, The resistance of the line per km is R'= 0,125 Ohm/km, the reactance per km is X'= 0,375 Ohm/km.With the help of given information; a) Calculate the current drawn from the line (IR) as a phasor. b) Calculate the line-to-line-neutral voltage (VS) as a phasor, determine the effective line-to-line voltage (US) Calculate its value. c) Calculate the line head power factor, active and reactive power drawn from the line head, d) Draw the phasor diagram of the system. ..
The length of a transmission line is (1000/3) kilometers. For this transmission line r=0.15 ohm/km x=0.8 Ohm/km y=5 * 10^-6 S/km given in the form. At the end of the line (36) MW is drawn and the end-of-line voltage is (220) kV. power factor: 0.95 (back) a. Assuming the line as a short line, calculate the VS and IS values with their angles. b. A, B, C, D by accepting the line as a mid-length line and using the "T" model approach. Calculate the parameters (Vs Is calculation is not needed) C. Calculate only parameter A, assuming the line as a long line.
A 3-ph, 50 Hz, 150 km line has resistance, inductive reactance and capacitive admittance of 0.1, 0.5 and 3 x 10-6 Ω per km per phase. If the line delivers 50 MW at 110 kV and 0.8 p.f. lagging, determine the sending end voltage and current assuming a nominal π circuit of the line.
Design a ‘π’ equivalent circuit for 320 km long 3-φ, 50 Hz transmission line.The line is composed of Drake conductors with the outside diameter of 2.8 cm and flat horizontal spacing of 3.65 m between adjacent conductors. The line has a resistance of 0.075 Ω/km.