2. An engine operating on the air standard heat engine has a compression ratio of 18. If the maximum cycle pressure at Isobaric heat addition is 55 bar, maximum and minimum cycle temperatures are 1893 K and 48°C, respectively. Determine • The amount of heat absorbed • The amount of heat rejected • The efficiency of the cycle The mean effective pressure

2. An engine operating on the air standard heat engine has a compression ratio of 18. If the maximum cycle pressure at Isobaric heat addition is 55 bar, maximum and minimum cycle temperatures are 1893 K and 48°C, respectively. Determine • The amount of heat absorbed • The amount of heat rejected • The efficiency of the cycle The mean effective pressure

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A regenerator of 75 percent effectiveness is used in an air-standard Brayton cycle working between pressures of 15 psia and 75 psia. Determine the work per pound of air and the efficiency of the cycle if the maximum and minimum temperatures of the cycles are 1700 R and 550 R, respectively.
In the preliminary design of a power plant, water is chosen as the working fluid and it is determined that the turbine inlet temperature may not exceed 520C. Based on expected cooling water temperatures, the condenser is to operate at a pressure of 0.06 bar. Determine the steam generator pressure required if the isentropic turbine efficiency is 80% and the quality of steam at the turbine exit must be at least 90%.
23. If the heat added in the Carnot engine is equal to 40kW and that the heat rejected amounts to 15.40kW. determine the higher temperature limit of the cycle if the lower temperature limit of the cycle is 30 C. a. 514.2526 C b. 514.2527 C c. 514.2528 C d. 514.2529 C
Define the Reversible Adiabatic Compression
A gas-turbine power plant operating on an ideal Brayton cycle has a pressure ratio of 8. The gas temperature is 300 K at the compressor inlet and 1300 K at the turbine inlet. Utilizing the air-standard assumptions and by accounting for the variation of specific heats with temperature, determine the thermal efficiency. The air can be treated as an ideal gas with κ = 1,4 and cp = 1006 J/(kg·K).
(a) Show the thermodynamic cycle of the Carnot engine on a T-s diagram(b) Determine the quality of steam in states 3 and 4. (c) Determine temperatures ?? and ?? (d) Determine the efficiency of the Carnot engine
25 - The refrigerant R-134a enters a throttling valve as a saturated liquid at 1400 kPa and leaves at 240 kPa. Which of the following is the degree of dryness of R134a leaving the valve? a) 0.3434 B) 0.4075 NS) 0.4520 D) 0.3339 TO) 0.4297
The thermal energy reservoirs of an ideal gas Carnot cycle are at 1240°F and 40°F, and the device executing this cycle rejects 100 Btu of heat each time the cycle is executed. Determine the total heat supplied to and the total work produced by this cycle each time it is executed
As a car gets older, will its compression ratio change? How about the mean effective pressure?
In an ideal diesel cycle the pressure and temperature at the beginning of the adiabatic compression are 98.5kN/m^3 and 60°c, respectively.themaximum pressure attained during the cycle is 4.5MN/m^3 and the heat received during the cycle is 580kJ/kg gas.Determine for the cycle a) the volume ratio of compression b) the temperature at the end of compression c) the temperature at the end of heat reception d) the temperature at the end of adiabatic expansion e) the net work done/kg of gas f) the thermal efficiency g) the work ratio h) the mean effective pressure I) the Carnot efficiency within the cycle temperature limits.
712. Which of the following is/are the process/es that cannot be found in a carnot cycle? a. isobaric compression b. isobaric expansion c. adiabatic expansion d. isothermal compression e. isothermal expansion f. adiabatic compression
0.5 kg of air (ideal gas) executes a Carnot cycle having a thermal efficiency of 50%. The heat transfer to the air during the Isothermal expansion is 40 kJ. At the beginning of the Isothermal expansion, the pressure is 7bar and the volume is 0.12m3. Determine, i) The maximum and minimum temperatures of the cycle in K ii) The volume of air at the end of Isothermal expansion iii) The work and heat transfer for each of the four processes.