2. Consider the voltmeter calibration data in Table 1. The sensitivity of the pressure sensor is 0.5 V/kPa (given by manufacturer) and the linear curve fit for the upscale calibration is given as y = 0.9829 x + 0.1095 .Plot the data using a suitable scale. a) Specify the percent maximum hysteresis based on full-scale range. b) Referring to increasing input calibration, determined the sensitivity and linearity errors. Increasing input (mV) Decreasing input (mV) Y Y 0.0 0.1 5.0 5.0 1.0 1.1 4.0 4.2 2.0 2.1 3.0 3.2 3.0 3.0 2.0 2.2 4.0 4.1 1.0 1.2 5.0 5.0 0.0 0.2 Table 1: Calibration results

2. Consider the voltmeter calibration data in Table 1. The sensitivity of the pressure sensor is 0.5 V/kPa (given by manufacturer) and the linear curve fit for the upscale calibration is given as y = 0.9829 x + 0.1095 .Plot the data using a suitable scale. a) Specify the percent maximum hysteresis based on full-scale range. b) Referring to increasing input calibration, determined the sensitivity and linearity errors. Increasing input (mV) Decreasing input (mV) Y Y 0.0 0.1 5.0 5.0 1.0 1.1 4.0 4.2 2.0 2.1 3.0 3.2 3.0 3.0 2.0 2.2 4.0 4.1 1.0 1.2 5.0 5.0 0.0 0.2 Table 1: Calibration results

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A force measurement system (weight scale) has the following specifications as shown in Table 1: Estimate the overall instrument uncertainty for this system based on available information. FSO refers to full-scale operating range.
In calibration of instrument the 0.055 percent of the calibration span what does it mean. If let say the range of pressure transmitter is 0 - 250 psi. Can you shown me the calibration results using 0.055 percnt calibration span.
1.The thickness of a gage block is measured five times using an instrument that has a resolution of 0.001 cm. The following measurements are obtained (in cm): 1.100, 1.110, 1.090, 1.095, and 1.105. The true gauge block thickness is known to be 1.050 cm. Use this information to answer the following questions: a. What errors or sources of measurement error can be identified in the example? (Hint: there are three). Identify each one as a random or systematic uncertainty. b. Estimate the magnitudes of each of these uncertainties. Wherever possible, estimate random uncertainties at a 95% probability/confidence level. c. Based on the uncertainties determined in part b, estimate the overall uncertainty of a measurement obtained by this instrument.
PLS ANSWER ASAP. THANK YOU! The slope of the calibration curve is based on __________. a. calibration limit b. calibration sensitivity c. calibration detection d. calibration function
Pressure distribution measurements are made on a two-dimensional wing model placed in a wind tunnel. The difference between the static pressure sockets on the surface and the static pressure of the free stream is measured. 30 data is taken at each measurement point. The average of the values measured from one of the sockets near the trailing edge was calculated as 2.30 Pa, and the standard deviation was calculated as 2.65 Pa. After applying the Chauvenet criterion to these measurement values, it was decided to eliminate 3 measurements and the new mean value was found to be 2.18 Pa and the standard deviation was 2.42. It was verified that the unexcluded data fit the normal distribution curve. Data above how many Pa and below how many Pa were eliminated? Estimate how many data have negative value (?<0) after elimination.
A displacement transducer has the following specifications: Linearity error:±0.25% reading Drift:±0.05%/°C reading Sensitivity error: ±0.25% reading Excitation: 10-25 V Output: dc 0-5Vdc Range: 0-5 cm The transducer output is to be indicated on a voltme- ter having a stated accuracy of 0:1% reading with a resolution of 10 μV. The system is to be used at room temperature, which can vary by 10 °C. Estimate an uncertainty in a nominal displacement of 2 cm at the design stage. Assume 95% confidence.
The transducer specified in Table 1.1 is chosen to measurea nominal pressure of 500 cm H2O. The ambient temperature is expected to vary between 18 ∘C and 25 ∘C duringtests. Estimate the possible range (magnitude) of each listedelemental error affecting the measured pressure. How do I calculate the sensitivity error? The solution that was given: Sensitivity error(eK) = (±0.0025)(500 cm H2O)= ± 0.75 cm H2O = ± 0.00375 V My Question is, how do you obtain 0.75 since 0.0025 x 500 gives 1.25! please help. thanks
Measurement in Engineering Question is image C) ? c) Determine a 95% confidence interval for Nu and report the value.
We wish to measure a characteristic of a machined part whose nominal size is 50 mm at 20 °C. For this, two different instruments are used; an analog micrometer and a digital vernier caliper, both recently calibrated and with the same resolution (0.01 mm). The calibration certificate data of the analog micrometer and the digital vernier are shown in tables 5 and 6 respectively. In both cases the calibration uncertainty does not include the contribution of resolution uncertainty. Additionally, there are drift studies for both instruments and it is established that the drift of the micrometer is ± 0.002 mm while the drift of the vernier is ± 0.02 mm. The same number of measurements were performed with both instruments to avoid repeatability biases under controlled environmental conditions. Table 7 shows the results of the measurements of both instruments. The temperature of the piece was monitored with a digital thermometer whose calibration uncertainty is 0.1 °C, which already includes…
Discuss the importance of measuring devices for Electric Motor and Internal Combustion Engine in terms of accuracy.
The transducer specified in Table 1.1 is chosen to measurea nominal pressure of 500 cm H2O. The ambient temperature is expected to vary between 18 ∘C and 25 ∘C duringtests. Estimate the possible range (magnitude) of each listedelemental error affecting the measured pressure refering to the solution provided online, Sensitivity error(eK) = (±0.0025)(500 cm H2O)= ± 0.75 cm H2O = ± 0.00375 V how do you get 0.75?? shoud it not be 1.25? according the answer, for sensitivity
A displacement transducer has the following specifications: Linearity error: ±0.25% reading Drift: ±0.05%/°C reading Sensitivity error: ±0.25% reading Excitation: 10-25 V dc Output: 0-5Vdc Range: 0-5 cm The transducer output is to be indicated on a voltmeter having a stated accuracy of 0:1% reading with a resolution of 10 μV. The system is to be used at room temperature, which can vary by 10 °C. Assume 95% confidence. The displacement transducer above is used in measuring the displacement of a body impacted by a mass. Twenty measurements are made, which yield Determine a best estimate for the mass displacement at 95% probability based on all available information.