2. Draw the positional sketch for excavator and also label all the symbols in the hy

Q: Determine the ratio of power

A: Given; Two shafts A and B are amde of the same material.Acc, to question;Diameter of shaft B is…

Q: Shift weight C so the lever would balance 1/4 of the total length of the board measured from left to…

A:

Q: In a vehicle when it is turned the axis of the wheel on the inside of curve turns through 45° angle…

A: Given data: -  The angle of the inside wheel is θ = 45o. The angle of outside wheel is φ = 30o. The…

Q: The structure diagram of the output shaft is shown as the following， please point out the wrong…

A: Please find the answer in the next page.

Q: the omnidrive that was mentioned above should be an agriculture related machine

A: Omni drive is an agriculture-related machine that is used to help the farmers in their fields.…

Q: Find FA and FB.

A:

Q: For the manipulator shown below: a) How many DOF are there? b) Draw the DH frames

A: Given that ;

Q: Find the ratio of the speed of the driving shaft to the speed of the driven shaft.

A:

Q: two pulleys are connected by a belt. The nubers of RPM of the two pulleys vary inversely as their…

A: Given data: The diameter of pulley 1 is, d1 = 25 cm. The diameter of pulley 2 is, d2 = 40 cm. The…

Q: lease write a precise overview/description of the precision tweezer below specifically for each…

A: Given Data : Precision tweezer

Q: belt drive is used when the shafts of pulleys are arranged parallel but rotate in the opposite…

A:

Q: Hi please recheck the answer for V because it is incorrect,

A:

Q: find Ax, Ay and Az

A: Write the given data with suitable variables. W=558 N/ma=1.5 mb=3 mc=1 m

Q: solve for thr CoP

A:

Q: (b) Compute the internal torque exerted on gear A (TAC), gear C(TcD) and gear D (TDB). (c) Sketch…

A:

Q: 01/ Give the dimensions for the hole and shaft for the 12 mm electric motor sleeve bearing (pump);

A: Given:Basic size given for motor sleeve bearing=12 mm

Q: n in the figure. If the drum

A:

Q: 2. It is used to loosen or tighten screws that have a star-like depression on the top, a feature…

A: Since you have posted a multiple independent questions in a single question. We will solve the first…

Q: maximum velocity of the follower

A: Given; Acc. to question,In a cam follower , the follower rises by h as the cam rotatesby δ…

Q: determine the speed of the tensioning pulley C in rpm?

A: To find RPM of C

Q: Shift weight A so the lever would balance at 7/8 of the total length of the board measured from left…

A:

Q: Pictures A and B show two different ways of holding a workpiece in the vice while using hacksaw. The…

A: We have to given answer of above question Pictures A and B show two different ways of holding a…

Q: ne weight of the piston is

A: P=7383.7N

Q: Q4) Show the instruments and the procedure used to test the concentricity of the spindle and the…

A: Disclaimer:“Since you have asked multiple question, we will solve the first question for you that is…

Q: Draw the neat diagram of shaper machine and label all its parts.

A: Given:- Shaper machine To find:- To draw a neat sketch of the shaper machine and to label it

Q: The other degree of rotation from the start point that will result in Erika being the same distance…

A:

Q: 1000 rpm

A: 5)  104.72rad/s 6)  16.67s 7) 91.89N/m

Q: A screwdriver is identified by

A: A screwdriver is a tool used to turn screws with slotted heads. It is normally used by hand.…

Q: Match the given functions with the components of a wind turbine. Connects the rotor hub to the gear…

A: a) Main Shaft connects the rotor hub to the gearbox.

Q: Create the front view of the sketch of the spur wheel (hand written asap))

A: Spur gear is used to transmit power and motion from one shaft to another. it will either increase or…

Q: ver AOB is pivoted at 0 and the

A: GivenOA=1mOB=1.2mBC=1.6mVAO=4m/s

Q: Which of the following statement is correct in terms of degree of freedom? Select one: O Moving left…

A:

Q: Weight and Balance Find the Empty Weight CG location for the following tricycle gear aircraft. Each…

A: Consider the moment diagram of the tricycle gear aircraft.

Q: 8-In lathe, the carriage and tail stock are guided on.. a) Same guideways. b) Different guideways.…

A: Solution:

Q: 6lb hammer of a pile driver is lifterd 5m the pilling head. If the hammer is released, what will be…

A:

Q: Using Free Hand Sketch, Draw the Three Views for Tow of the following bodies.

A: Please refer the below images for the required free hand sketches.

Q: haft trar Is, then t

A: given:power P=1000kwω=100rad/s

Q: Determine the name of the device and

A: Given; Moist air at 350 CRelative humidity is entering a psychometric deviceand leaving at,…

Q: If C, is the coefficient of speed fluctuation of a flywheel, then ratio of wma/@min will be

A:

Q: Find warrk done

A:

Q: Create the front view of the sketch of the spur wheel (hand written)

A: Spur gear: Spur gears are used to increase or decrease the speed, or to multiply torque by…

Q: How many rotations of a 1 m diameter wheel would it take to traverse 50 m of distance.

A: Given data :-  Diameter d = 1 m  Distance = 50 m  Find :-  How many revolutions = ?

Q: Draw the front and right vlews of the solld below. Front Right

A: The front view and side view of the figure shown above will look exactly same. In both, the views…

Q: Shift weight C so the lever would balance 3/8 of the total length of the board measured from left to…

A:

Q: speed.

A: Given; A milling cutter having teeth is rotating at;  N= 135 rpmIf the tooth is, f=0.1 mmDetermine…

Q: Draw FBD of Bicycle axle (Thru axle)

A: To find :- Fbd of axle

Q: Sketch a typical turbine speed (rpm) VS wind speed characteristics (which indicates how turbine…

A: Given :- Rated speed = 18 rpm

Q: i) it is rotated

A:

Q: (d) Calculate the magnitude (in m/s?) and direction (in degrees above or below the hor

A: