Question 5 .SavedThe rotational speed of 1000 rpm is equivalent to104.72 rad/s159.15 rad/s16.67 rad/sQuestion 6SavedThe rotational speed of 1000 rpm is equivalent to a period of0.06 s16.67 s0.6 sQuestion 7Consider four springs with spring constants kl= 20N/m , K2=50 Nm K3=100 Nm, K4=200 Nm, What is theequivalent spring constant if K123 are in parallel and with K4 in series.360 N/m270 N/m91.89 N/m

5) 104.72rad/s 6) 16.67s 7) 91.89N/m

Answered: 1000 rpm

Engineering

Mechanical Engineering

1000 rpm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please include explanation. A 6-MW offshore wind turbine has a capacity factor of 40%. It has a height of 120 m, and 107-m long blades. The angular acceleration is 1.388 rad/s2. Assume that the distance from the center of the turbine to the connection with the blade is negligible, and that the turbine starts from rest. At ? = 12 s, calculate the velocity and the acceleration for points (a) at half the length and (b) at the tip of the blade.
A load is raised 11 ft by the gears and wheel system below. Gear A is initially rotating at rest and accelerates uniformly to omega = 24 rpm in t= 10 sec and maintain then maintain this constant 24 rpm speed. The dimensions are rA= 1 in, rB= 9 in and rC=16 in. 1) From 0 to 10 sec, find alphaA1, alphaC1 in rad/s^2, omegaA1(t), omegaC1(t) in rad/s, thetaA1(t), thetaB1(t) and thetaC1(t) in rad, and the distance made by the load s1 in inches and in feet made by the load during this time. 2) After 10 sec, find the distance s2 in feet and in NC es needed to reach the 11 ft, find thetaC2(t), alphaA2, alphaB2 in rad/s^2, omegaA2(t), omegaB2(t) in rad/s, thetaA2(t), in rad and the distance s2 in ft that should be made to get to the 11 ft raising distance of the load. 3) Deduce the number of revolutions made by gear A and how long it will take, to raise the load up to 11 ft. In the box below, give the time it takes to raise the load in seconds, with one decimal.
A load is raised 11 ft by the gears and wheel system below. Gear A is initially rotating at rest and accelerates uniformly to omega = 24 rpm in t= 10 sec and maintain then maintain this constant 24 rpm speed. The dimensions are rA= 1 in, rB= 9 in and rC=16 in. 1) From 0 to 10 sec, find alphaA1, alphaC1 in rad/s^2, omegaA1(t), omegaC1(t) in rad/s, thetaA1(t), thetaB1(t) and thetaC1(t) in rad, and the distance made by the load s1 in inches and in feet made by the load during this time.
This most likely is made to be a probelm about mx''+bx'+kx=f(t) m = mass b = friction k = spring constant 4. A mass weighing four pounds stretches a spring 24 in. Suppose the mass is atequilibrium and is set into motion with a velocity of 6 inches per second. The mass is in a mediumwhere friction is small, and we assume it is zero. Note that the acceleration due to gravity near theearth’s surface where the experiment takes place can be taken as 32 ft/s2.(a) Suppose that in addition to the conditions described above, a hammer strikes the mass everyπ/2 seconds starting at t = 0. A delta function with impulse of 1 pound-second models theforce of each blow to the mass. Find the function x(t) for the displacement from equilibrium infeet of the mass at time t in seconds. Express x(t) as a piecewise defined function without the use ofunit step or Heaviside functions and such that in each time window it is a different multiple of the samesinusoidal function.(b) Now assume the same spring-mass…
.A cast iron flywheel with mean radius of 250 mm runs at average of 100 rad/s and has a maximum fluctuation of energy ∆KE of 2500 N-m. If the coefficient of fluctuation of speed of 0.01. which of the following is the mass of the flywheel rim? choices: 400 kg 100 kg 25 kg 4 kg
A load is raised 11 ft by the gears and wheel system below. Gear A is initially rotating at rest and accelerates uniformly to omega = 24 rpm in t= 10 sec and maintain then maintain this constant 24 rpm speed. The dimensions are rA= 1 in, rB= 9 in and rC=16 in. 2) After 10 sec, find the distance s2 in feet and in NC es needed to reach the 11 ft, find thetaC2(t), alphaA2, alphaB2 in rad/s^2, omegaA2(t), omegaB2(t) in rad/s, thetaA2(t), in rad and the distance s2 in ft that should be made to get to the 11 ft raising distance of the load. 3) Deduce the number of revolutions made by gear A and how long it will take, to raise the load up to 11 ft.
. During the operation of a punch press, its flywheel decelerates uniformlyfrom 400 rpm to 200 rpm in l sec. The rim of the flywheel weighs 1288 lb, itsinside and outside diameters are 56 in. and 60 in., and it is attached to itshub by 6 spokes. What average shearing force is developed between the rim andeach spoke during the 1 sec interval?
The turning moment diagram for a petrol engine is drawn to the following scales: turning moment 1 mm to 2·5 Nm; crank angle, 1 mm to 1°. The fluctuations of energy between the crank positions for minimum and maximum speeds corresponds to an area of 600 mm² of the turning moment diagram. The flywheel is made from cast iron, of density 7·2 tonnes/m3. Determine: (a) The greatest fluctuation of energy (b) The mass of the flywheel required to prevent the a fluctuation of speed greater than ± 0·5% from the mean speed of 1600 rev/min if the radius of gyration is 120 mm. (c) The dimensions of the flywheel (diameter and thickness) (d) Describe the possible consequences to the system if the flywheel was not used to limit the fluctuation of speed.
Example 9.15 A rope, to which a weight is attached, passes around a pulley 50 cm in diameter. The angular acceleration of the pulley is 18 rad/s2. If the pulley is initially rest, find a- The time required for the weight to attain a velocity of 15 m/s b- The number of revolution through which the pulley rotates during that period, c- The total acceleration of a point on the rim of the pulley 0.5 second after it was at rest.
A flywheel absorbs 2500 ft-lb of energy at a coefficient of fluctuation of 0.10. The mean diameter of the flywheel is 72 inches. The weight of the arms and hub is 12 % of the rim weight. The mean rim speed is 80 fps. Consider the specific weight of the flywheel as γ = 0.26 lb/in3. A. Find the mean rpm of the rim. B. Determine the weight of the rim. C. What is the cross sectional area of the rim?
The turning-moment diagram for one cycle of a multi-cylinder engine shows fluctuations in energy above and below the mean-torque line as follows: –62·5 J, +105·7 J, –27·3 J, +63·3 J, –59·1 J, +25·2 J, –99·3 J and +54 J. Sketch the diagram and use it to find the mass of the flywheel, radius of gyration 220 mm, needed to keep the engine speed within the range 898 to 902 rev/min
A stroke of a reciprocating engine is 600 mm. neglecting the effect of angularity of the connecting rod, find a) velocity in m/s of the piston , b) acceleration of the piston in m/s^2 when the crank is 30 degree past TDC. The engine is running at 720 rev/min tools : r=1/2 stroke, v=wrsin theta! a=wr^2costheta