Complete solution 11.24showsaFigureHumpage gear used in a latheheadstock. The number ofteeth on the wheels B, C, D, Eand F are 18, 54, 22, 44 and72 respectively. If the shaft G rotates at 200 rpm,what will be the speed of the shaft H when (i) Fis held stationary, and (ii) it is rotated at 30 rpmopposite to G?D.Fig. 11.24

Answered: Image /qna-images/answer/ff087f70-e8c7-400f-bb4b-0ea803bdb5a7.jpg

Answered: i) it is rotated

Engineering

Mechanical Engineering

i) it is rotated

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Two parallel shaft connected by spur gears turn in the same direction and having a speedratio of SR = 4.72 (a) What is the distance of the two shaft, in mm, if the smaller gear is170 mm in diameter? (b) What is the diameter of the larger gear in mm?
what is the equation of the normal, transverse, and axial circular pitches in helical gears
What are the harmful effects of backlash error in gears?
what is the equation of the addendum and dedendum in helical gears
6. The loaded radius of the pneumatic tire of the ground-wheel driven grain drill is16 inches. The estimated slippage is 18% and the required ground speed ofthe grain drill is 7 kph. How many revolutions should the wheel be turned toachieved this. Solve on paper
gearing arrangement suitable for the given application is.
Two spur gears of 24 teeth and 36 teeth of 8 mm module and 20° pressure angle are in mesh. Addendum of each gear is 7.5 mm. The teeth are of involute form. Determine : 1. the angle through which thepinion turns while any pair of teeth are in contact, and 2. the velocity of sliding between the teethwhen the contact on the pinion is at a radius of 102 mm. The speed of the pinion is 450 r.p.m
Two spur gears transmit 36kW with a velocity ratio of 2:1. The speed of the smaller driving gear is 100rpm. The centre distance between the shafts is to be as near as possible to 920mm. If m=10 and all-21MPa, determine a) Diameter of the shafts b)PCD for each wheel c)Number of teeth on each wheel d) Actual centre distance [ e) Width of the teeth
Please solve in 30 min The teeth number of each gear is already given (e.g. Z₁ =14). If the rotation speed of gear 1 is n₁=380 r/min, calculate the rotation speed of gear carrier H
Two 20º full-depth steel gears are heat treated to BHN=350. AGMA Quality No.8 Pinionturns 860 rpm. N1=24c; N2=96; Pd=4, and b=2in. Find the horsepower the gears aretransmitting. Ans: hp=77.2
A gear system comprises gear A, which is stationary. The bar A'C' rotates with an angular velocity ω1 of 5 rad/s. What will be the angular velocity of gear C? Diameters of the gears: DA = 600 mmDB = 350 mmDC = 200 mm Note: Solve gears B and C by IC method and by relative velocities method
I n a reverted gear train, as shown in Fig. Q2, two shafts A and B are in the same straight line andare geared together through an intermediate parallel shaft C. The gears connecting the shafts Aand C have a module of 2 mm and those connecting the shafts C and B have a module of 4.5 mm.The speed of shaft A is to be about but greater than 12 times the speed of shaft B, and the ratio ateach reduction is same. Find suitable number of teeth for all gears. The number of teeth of eachgear is to be a minimum but not less than 16. Also find the exact velocity ratio and the distance ofshaft C from A and B