2. For the following system shown in the figure, calculate: a. The current through each phase of the load. b. The total real and reactive power of the three-phase load. c. The power factor at the load side. A 220 V20° 20VL-120° U8 vol B 152 9. I 220 VI20° elee 122

2. For the following system shown in the figure, calculate: a. The current through each phase of the load. b. The total real and reactive power of the three-phase load. c. The power factor at the load side. A 220 V20° 20VL-120° U8 vol B 152 9. I 220 VI20° elee 122

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.13MCQ

See similar textbooks

Related questions

Q: what is the needed reactive power per phase to achieve the required power factor for load 1 and load…

Q: A balanced three-phase source with grounded neutral has line-to-line voltages of 208 volts with…

A: It is given that: VL-L=208 voltZab=45-j25; Zbc=25+j50; Zca=60+j80 ohms

Q: Given: 1. 2 wye-connected loads per phase to a 3 phase power source 2. first load consists of a…

Q: A balanced three-phase Y-source with Vph = "224" V rms drives a Y-connected three-phase load with…

A: Given: For balanced 3-phase source: Assuming the positive phase sequence A-B-C for source, the phase…

Q: Q4) The three phase circuit seen in the following figure is derived by a three phase balanced…

A: the sinusoidal steady-state solution of the iR (t) current , and . the total complex power consumed…

Q: 18: A series resistive inductive load is energized from a 240V(RMS), 50HZ single phase A. supply,…

A: Given a series RL circuit having, Energized voltage, V = 240 V (rms) Frequency, f = 50 Hz Active…

Q: 12. An inefficient three-wire single-phase system has source voltages of Van = Vnb=720/0° V, line…

A: Given data, Van = Vnb = 720∠0° V,Line resistance RaA = RbB = 1ΩRnN = 10ΩLoad ZAN = (10+j3 )Ω, ZAB…

Q: 1. 2 wye-connected loads per phase to a 3 phase power source 2. first load consists of a 55ohm…

Q: DIagram: FauLt h phase 3phase Load Source 2 Line Values: sourte Line Impedances: • Eon: 120 L0' v •)…

A: Under unbalanced condition with fault We have to find load power profile Active (PT), reactive (QT),…

Q: A 208Vrms delta power supply is connected to an unbalanced 3-phase load. Z1 = -j1200 Z2 = -j600…

A: Note: 208 V rms voltage of delta connected supply is given. it is not mentioned about which phase…

Q: A 3-phase system has line to line voltage Vab = 1500 Vrms with 30 deg angle with a wye load.…

A: For star load line voltage is sq rt(3) times of phase voltage and leads by angle of 30 degree

Q: 2 wye-connected loads per phase to a 3 phase power source 2. first load consists of a 55ohm…

Q: For the following three-phase system. EAB = 120 V 0° Iab ab ca 3-phase, 3-wire A-connected ac…

A: Power system

Q: Assume that the phase-voltage magnitudes for a wye system are 100V. Find the magnitude of the…

Q: Zy Is Zy S Zy IT

Q: 2 wye-connected loads per phase to a 3 phase power source 2. first load consists of a 55ohm…

Q: Q. 2a) The impedance Zi and Z2 are connected in parallel across 200 V, 50 HZ single phase ac supply.…

Q: For the following system shown in the figure, calculate: A B C 220V40° 220VL-120° 220 V4120° с 12.12…

Q: e) Calculate the phase current IAB. f) Calculate the total average power dissipated in the…

A: In the power system Find the phase current Total dissipate power across the load Ratio of the power…

Q: Three equal impedances of (8 + j6) ohms are connected across a 3-phase supply. The phase voltages…

A: Power system has loads and sources present. They can be balanced and unbalanced. For easy…

Q: 3. A balanced three phase wye connected source has using "negative phase sequence, Van = 220 V rms…

Q: Using Negative Phase Sequence Determine: a) Phase Voltages Power delivered to the load USE3 DECIMAL…

A: The circuit can be redrawn as Here we can see that the given circuit is balanced. So, we can…

Q: 4. A balanced wye-connected, three-phase load withdraws 150 A per phase with a leading power factor…

A: The solution is given below

Q: lanced three-phase source with grounded neutral has line-to-line voltages of 208 volts with ab-bc-ca…

A: In this question, A balanced three-phase source with grounded neutral line-to-line voltagesVLL =…

Q: 19 A balanced three-phase voltage source, Van = 200/0° V rms, positive phase sequence, is connected…

Q: 200 /25 Vms IL 200 -95 Vrms 200 /145 Vms 3 IL Ze

Q: Problem 6 Compute the power delivered to the wye-delta load by the three-phase generator in the…

A: Let us convert the delta connected impedances to their star equivalents to make the calculations…

Q: a)When three inductive loads, each of reactance 9 Ω and resistance 4 Ω are connected in delta which…

A: As you have not mentioned which question has to solve so I am solving only (a). It is given 3 phase…

Q: A three-phase source has a phase sequence of EAS- Esc - ECA and delivers the following delta load…

Q: The load shown below is connected to a 360 V, 50 Hz three-phase supply with a positive phase…

A: The load shown below is connected to a 360 V, 50 Hz three-phase supply with a positive phase…

Q: A balanced three-phase delta-wye system is shown in Figure 1. For positive phase sequence, calculate…

A: This is the balanced source and balanced load case, we can apply Mesh loop equations to get current…

Q: If a single phase of a balanced three-phase source delivers an apparent power of Sp = 10260° VA, how…

A: Given a balanced three phase circuit The apparent power of the single phase is Sp=10∠60°VA

Q: Referring to the circuit shown below, determine the following: (a) The voltage between points e and…

A: Calculation of voltage and power factor of above circuit.

Q: la A Z2 VAB VCA IAB ICA B Z3 TBC le VBC

A: In the Star Connection, the 3 winding's similar endpoints are connected to a common point known as…

Q: QUESTION 3 Find the magnitude of the phase voltage of a wye-delta system that has a balanced load of…

A: This problem is from star delta system of load the answer is option d

Q: R , Vor V 200VZ-10° , (assume positive sequence) %3D ry o=Z = 12 +j 4 a) Show all type of current…

Q: Figure Q1(b) shows a three-phase electrical circuit connected in Y-A configuration. The line voltage…

A: For sketching the per phase circuit, we will convert the delta connected load to star connection for…

Q: A balanced Star connected three-phase load draws 150 A per phase with a leading power factor of 0.7…

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Q: B) A three-phase, 50 Hz, A-Y connection. The line voltages of primary and secondary are 3300V and…

Q: Calculate the line currents in the following 3-phase unbalanced system. Find the active, reactive…

Q: A 70 KV short transmission line is 20 Km with per phase ine impedance of (0.125 p.5) ohms. The Ine…

Q: Which of the following statements is corect, Magnitude of the phase voltage is greater than the…

A: Consider the first statement Consider the expression for the relation between phase voltage and…

Q: An unbalance delta connected three phase load shown in the figure is supplied by a balanced three…

Q: Balanced 3 Phase Supply A CC PC S BCN A 90 Balanced 3 Phase Load IN B The 3-phase load consumes a…

A: Methods of power measurement in three phase circuit One wattmeter method Two wattmeter method…

Q: An unbalance delta connected three phase load shown in the figure is supplied by a balanced three…

A: Note Resistance absorb active power only , it does not take any reactive power Capacitance and…

Q: Suppose you have a three-phase generator that provides 120 Vac per phase and works at a frequency of…

A: Here in this solution the concept power & power factor for the delta & star connected 3…

Q: vs 60 kVA at lagging PF of 0.8, while load 2 draws 26.667 ume no line resistance and Vab-440L 30°…

A: In this question given 2 loads ...We have to find out total power dream by loads , phase currents…

Q: What would be the phase-to-neutral voltage from a 3-phase, wye-connected system if the line-to-line…

Question

2. For the following system shown in the figure, calculate:
a. The current through each phase of the load.
b. The total real and reactive power of the three-phase load.
c. The power factor at the load side.
A
220 V 20°
220VL-120°
U8 vol
152
I 220 VI20°
9.
M.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Single Phase Controlled and Uncontrolled Rectifiers

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The instantaneous power absorbed by the load in a single-phase ac circuit, for a general R LC load under sinusoidal-steady-state excitation. is (a) Nonzero constant (b) Zero (c) Containing double-frequency components
)Two complex loads Z1 and Z2 are connected in parallel and powered by a value voltage effective 7.2 kV and frequency 60 Hz. The first load has a power of 50 kVA and a factor of rear power of 0.9. The second charge has a power of 45 kW and a rear power factorof 0.91. Determine in steady state the kVAR power and the capacity required to correct the Total power factor to a value of 0.97 rear.
A load has a leading power factor. a) Is it a capacitive or inductive load? b) Is the reactive power positive or negative? c) Repeat for a load with lagging power factor
Assum rms for the phase current
The p.u. impedance value of an alternator corresponding to base values of 13.2 kV and 30 MVA is 0.2 p.u. Then the p.u. impedance value of an alternator for the new base values of 13.8 kV and 50 MVA is......
Use the information below to answer questions 24 und 25. The voltage across and the current through a load are (10+ j5Y and (2-jiArespecively. 24. What is the reactive power in VArconsumed? D. 0 A. 15 C. 20 D. 25 25. What is the pawer factor of the load? A. 0.8 leading B. 0.8 Jagging. -D. 0.6 ligging C 0.6 leading
1980628cmid 11616 For reactive load, the power factor is equal to Select one: O a. 1 O b. 90 O c. 2 O d.0 If the voltage V, = 800 mV, then the current flowing in the primary winding Ip is: j2on Select one: O a. None of these O b. l, =40<0° mA O c.l, = 0.320<90° A O d. Ip =320<-90° mA if a Load absorbs an average power of 8 kW at a lagging power factor of 0.5 Select one: O a. -8000 + j13856.4 VA O b. None of these O c. 8000 - j13856.4 VA O d. 8000 - j13856.4 VA estion-299141-3 freactive power is
There is an installation with two equal triphasic loads of 300 kVA each and a power factor of 0.9 lagging. When connecting a pure reactive element in parallel, the reactive power at the entrance of the installation is 150 kVARS, with a lagging power factor. We can say that: a) A bank of reactors was connected and the fp deteriorated. b) A capacitor bank was connected and the pf deteriorated. c) A bank of reactors was connected and the fp improved. d) A capacitor bank was connected and the pf improved. e) None of the above
Which cannot be said since Z is an inductive load in the circuit given below? A) load voltage period is 0.02sec. B) Load voltage peak value is 311V. C) Load voltage frequency is 50Hz D) Load voltage average value is 220V.
The section bus-bars A and B are linked by a bus-bar reactor rated at 6000 kVA with 12% reactance. On bus-bar-A, there are two generators each of 10 MVA with 8% reactance and on bus-bar-B, two generators each of 6000 kVA with 10% reactance. Find the steady MVA fed into a dead short circuit all phases on B with bus-bar reactor in the circuit.
Consider a 10 kVA, 200/400 V, 50 HZ: single-phase tranformer has the folloving test results:0.C. test: 200 V, 0.6A, 63 W (L.V.side)S.C. test : 20 V, 25A, 85 W (H.V. side)Deternine:i- The eficiengy at 75 % offiull-load at 0.9 leading power factor.ii -The secondary terminal voltage on fill-load at tunity power facton
what is the reactive power absorbed by the load ZL in VAR? Assume source is in rms