QuestionA 70 KV short transmission line is 20 Km with per phase line impedanoe of (0.125 p.5) ohms. The Ine dellvers 70 MVA with G power factor lagging t s KV. FindL Total Transmisaion Line Impedance par phaneH. Recelving end voltage per phase. Complex, Real and Reactive PowerN. Send end current per phaseV. Receiving end voltage (line to line)Note: Show all your steps on BBLeam.

Answered: Image /qna-images/answer/d1eaa498-9b1d-41bf-a82d-2669e5469fb3.jpg

A 70 KV short transmission line is 20 Km with per phase ine impedance of (0.125 p.5) ohms. The Ine delvers T0 MVA with 08 power fackor lagging w es V. Find L Total Transmission Line impedance per phase . Recelving end voltage per phase H. Complex, Real and Reactive Power . Send end current per phase V. Recelving end voltage (line to line)

A 70 KV short transmission line is 20 Km with per phase ine impedance of (0.125 p.5) ohms. The Ine delvers T0 MVA with 08 power fackor lagging w es V. Find L Total Transmission Line impedance per phase . Recelving end voltage per phase H. Complex, Real and Reactive Power . Send end current per phase V. Recelving end voltage (line to line)

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter10: System Protection

Section: Chapter Questions

Problem 10.1P

See similar textbooks

Similar questions

Figure 3.32 shows the oneline diagram of a three-phase power system. By selecting a common base of 100 MVA and 22 kV on the generator side, draw an impedance diagram showing all impedances including the load impedance in per-unit. The data are given a follows: G:90MVA22kVx=0.18perunitT1:50MVA22/220kVx=0.10perunitT2:40MVA220/11kVx=0.06perunitT3:40MVA22/110kVx=0.064perunitT4:40MVA110/11kVx=0.08perunitM:66.5MVA10.45kVx=0.185perunit Lines I and 2 have series reactances of 48.4 and 65.43, respectively. At bus 4, the three-phase load absorbs 57 MVA at 10.45 kV and 0.6 power factor lagging.
A balanced three-phase load is connected to a 4.16-kV, three-phase, fourwire, grounded-wye dedicated distribution feeder. The load can be mode led by an impedance of ZL=(4.7+j9)/phase, wye-connected. The impedance of the phase conductors is (0.3+j1). Determine the following by using the phase A to neutral voltage as a reference and assume positive phase sequence: (a) Line currents for phases A, B, and C. (b) Line-to-neutral voltages for all three phases at the load. (c) Apparent. active, and reactive power dissipated per phase, and for all three phases in the load. (d) Active power losses per phase and for all three phases in the phase conductors.
470 kVA load at 12 kV. Its resistance is 7 Ω and inductive reactance is 7 Ω if the load power factor is 0.9 lagging. Determine the Current through the line , Sending end voltage , Sending end power factor , Regulation of transmission line , Efficiency of transmission line Note:please do not handwriting
A short 3-phase transmission line connected to a 33kV, 50 Hz generatingstation at the sending end is required to supply a load of 10 MW at 0·8lagging power factor at 30 kV at the receiving end. If the minimumtransmission efficiency is to be limited to 96%, estimate the per phasevalue of resistance and inductance of the line.
Question-2) The parameters of a three-phase transmission line are given as Z = (12.84 + j72, 76)Ω and y = j5, 83x10^-4 mho. At the end of the line, a power of 55 MVA with a power factor of 0.8 is drawn under 132 kV voltage. Accordingly, calculate the line head voltage, active and reactive power values per line, and voltage regulation of the line using the nominal π circuit.7-) Since 55 MVA power is drawn from the end of the line under the conditions mentioned above, calculate the line head voltage (phase-phase voltage) and enter it in the box below. (The value will be entered in kiloVolts. Only the amplitude value of the voltage will be entered. The phase value will NOT be entered!!! Two digits after the comma will be sufficient. )8-) Since 55 MVA power is drawn from the end of the line under the conditions mentioned above, calculate the active power value per line and enter it in the box below. (The value will be entered in MegaWatt. It will be sufficient to take two digits after…
An 11 KV, 3-phase transmission line has a resistance of 1.5 Ω and reactance of 4 Ω per phase.Calculate the percentage regulation and efficiency of the line when a total load of 5000 KVA at 0.8 lagging power factor is applied at 11KV at the distant end.
Problem 5. An 11 kV, 3-phase transmission line has a resistance of 1·5 Ω and reactance of 4 Ω per phase. Calculate the percentage regulation and efficiency of the line when a total load of 5000 kVA at 0.8 lagging power factor is supplied at 11 kV at the distant end.
A short 3-φ transmission line with an impedance of (5 + j 20) Ω per phase has sending end and receiving end voltages of 46·85 kV and 33 kV respectively for some receiving end load at a p.f.of 0·8 lagging. Determine : (i) power output(ii) sending end power factor
A single-phase transmission line has a resistance of 0.22 ohm and inductive reactance of 0.36 ohm. Find the voltage at the sending end to give 500kva at 2000V at the receiving end at a load power factor of 0.707 lagging. Also find the efficiency of transmission at this load.
Determine the current in the neutral conductor and the current in each line conductor (i.e., IR, IB andIY) using the given information below. The powers 12 kW, 18 kW and 24 kW are the loads of a purely resistive loads which are between the yellow and blue, the red, and neutral phases respectively of a 3-Φ, four-wire system.415 V is the line voltage. Find the active power (in kW) in the main network and in. each branch and the apparent power (in kV A) using the given information below. Two branches connected in parallel had a p.d. of 200∠30° V applied to them. The currents in the respective branches are 20∠60° A and 40∠30° A. Thanks
A short single phase transmission line has a loop impedance of (0.2+j1.2) ohm. At what leading power factor the voltage regulation will be zero ?
For the power system with a single line diagram;Draw the reactance diagrams of the zero, positive and negative component circuits of the system by selecting the base values of 1000 MVA and 20 kV in the generator G3 region. (?0=?1=?2=50 ?ℎ? for each line)