2. IN THE SYSTEM SHOWN, THE COEFFICIENT OF FRICTION BETWEEN BLOCK A AND THE PLANE IS 0.25. NEGLECT THE MASS AND FRICION OF THE PULLEY. A. DETERMIME THE VELOCITY OF THE BLOCK A AFTER IT HAS MOVED 2 METERS B. DETERMIME THE VELOCITY OF THE BLOCK B AFTER B HAS MOVED 2 METERS C. DETERMIME THE TIME IT TOOK A TO MOVE A DISTANCE OF 2 METERS 240 kg A 720 kg B

2. IN THE SYSTEM SHOWN, THE COEFFICIENT OF FRICTION BETWEEN BLOCK A AND THE PLANE IS 0.25. NEGLECT THE MASS AND FRICION OF THE PULLEY. A. DETERMIME THE VELOCITY OF THE BLOCK A AFTER IT HAS MOVED 2 METERS B. DETERMIME THE VELOCITY OF THE BLOCK B AFTER B HAS MOVED 2 METERS C. DETERMIME THE TIME IT TOOK A TO MOVE A DISTANCE OF 2 METERS 240 kg A 720 kg B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

If the e = 45°, and the bar 0Q is rotating in the counterclockwise direction at 1.6 rad/s, which of the following is the velocity of the slider P?.
Assume the coefficient of friction = 0.22, A = 175N and B = 96N. Find the least value of P to cause impending motion and the value of θ.
A boy slides down a water chute starting from rest at A. Neglecting friction. a. which of the following gives the velocity at the end of the chute at B in ft/s. b. which of the following gives the velocity on entering the water at C in ft/s. C. which of the following gives the horizontal distance of C from B in miles.
A block weighing 100Nis held on a 40 ̊incline by a bar attached to a 150N block on a horizontal plane. The bar, which is fastened by smooth pins at each end, is inclined 20 ̊above the horizontal. The angle of friction between each block and its plane is 18 ̊. Fin the horizontal force P applied to the 150N block which will cause to be on the point of moving (a) to the right; (b) to the left.
a stepladder consisting of two legs pinned together at C is resting on a rough floor. will 800 N worker be able to change the light bulb if he is required to climbed to a height of 1.3 m? The uniform legs AC and BC weigh 110 N and 70 N, respectively. the coefficient of static friction is 0.48
An experimental device imparts a force of magni tude F = 225 N to the front edge of the rim at A to simulate the effect of a slam dunk. Determine the moments of the force F about point 0 and about point B. Finally, locate, from the base at 0, a point C on the ground where the force imparts zero moment.
4. An open cylindrical tank 2 m in diameter and 4 m high contains water to a depth of 3 m. It is rotated about its own vertical axis with a constant angular speed. a. If w = 8 rad/s, how much water is spilled out and to what depth will the water stand when brought to rest?b.What angular speed w (in rpm) will just zero the depth of water at the center or the tank?c.If w = 100 rpm, how much area at the bottom of the tank is uncovered?
The wooden block (mass m = 0.5358 kg) is released from rest at A by a compressed spring (compressed length 0.6 m, undeformed length 1 m, spring constant k = 150 N/m). The block is allowed to slide through the rough horizontal surface (A to B), then along the smooth circular ramp (B to C, central angle θ = 47.2°, until the block is released after point C. Calculate the speed of the block at points B and C. Also, what is the magnitude of the normal force exerted to the block just before the block leaves the ramp? Neglect the geometry of the block.NOTE: Use Work-Energy Method to solve for the speeds; use Force-Mass-Acceleration (FMA) Method to compute for the normal force.
9. The coefficient of active pressure for an angle of internal friction of 28.4° is: Round off to three decimal places.
Determine the magnitude of the horizontal reaction (N) at A if P = 254 N and Q = 2395 N. Let x = 2.48 m, y = 2.5 m, and z = 2.05 m. Round off only on the final answer expressed in 3 decimal places. Instead of units, indicate the direction of the horizontal reaction at A: use R if to the right and L if to the left.
Determine the distances x and y for equilibrium if F1 = 800 N and F2 = 1000 N.
A block of mass m = 2.00 kg rests on the left edge of a block of larger mass M = 8.00 kg. Thecoefficient of kinetic friction between the two blocks is 0.300, and the surface on which the 8.00-kgblock rests is frictionless. A constant horizontal force of magnitude F = 10.0 N is applied to the2.00-kg block, setting it in motion as shown in Figure P5.65a. If the length L that the leading edgeof the smaller block travels on the larger block is 3.00 m, (a) how long will it take before this blockmakes it to the right side of the 8.00-kg block, as shown in Figure 3? (Note: Both blocks are set inmotion when F is applied.) (b) How far does the 8.00-kg block move in the process?