A 3 ft. diameter log (sp.gr.= 0.82) divides two shallow ponds as shown. 12 3 R₂0 Pr Rx D Fi Ry F₂ 12 1.5 Compute the net vertical reaction at point C if the log is 12 ft. long. Compute the horizontal reaction at point C. Compute the direction of the resultant force w/ the horizontal at point C.

A 3 ft. diameter log (sp.gr.= 0.82) divides two shallow ponds as shown. 12 3 R₂0 Pr Rx D Fi Ry F₂ 12 1.5 Compute the net vertical reaction at point C if the log is 12 ft. long. Compute the horizontal reaction at point C. Compute the direction of the resultant force w/ the horizontal at point C.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 2 m 1 m 0.5 m 0.25 m F B 1.5 m 0.25 m E x

Q: The following shows a schematic section of a three-story reinforced concrete building. The building…

A: To determine- Base shear coefficient of the building

Q: The following data were obtained from a triaxial test on a cohesive soil: Maximum shearing stress at…

A: Given data in question Shearing stress 65 kPa Angle of friction 28° Cohesion 31 kPa To find out…

Q: In the following photo, identify the type of footing that is being installed. Photo A: Photo A:…

A: Given data in question Foundation site picture To find out Which type of Foundation is this

Q: Find the vertical stress at depth 10m below point A on the loaded area shown in figure if Aq=100…

A: GIVEN Radius , R=10m Depth , Z=10 m △q=100KN/m2

Q: at C. Determine the reaction forces of the roller at A, the hinge at B and the fixed support lk / H…

Q: The following shows the cross section and bending moment diagram of a two-bay continuous beam. The…

A: b=24 inch d=28 inch stirrups- #4 Maximum moment - 750 k-ft Bar size- 7- #8 bars To determine- width…

Q: 9.32. A catchment has the Horton infiltration parameters fo= 150 mm/h, fc = 50 mm/h, and k = 3…

A: Given:- The Horton's infiltration parameters are:- f0 = 150 mm/h fc = 50 mm/h k = 3 min-1 To…

Q: 1. A W460 x 177 column section has length of 8 m. Using NSCP 2015 Specification: Fy = 380 MPa A =…

A: Answer Member W 460 x 177 is non slender member (A) Calculation of safe axial load using ASD and…

Q: The following shows the cross section and bending moment diagram of a two-bay continuous beam. The…

A: b=24 inch d=28 inch stirrups- #4 Maximum moment - 750 k-ft Bar size- #10 To determine- No. of bars

Q: Determine the magnitude of the vertical force P of the cable loaded as shown. 3.0 -8' fst B 7K C…

A: Given To Find The magnitude of vertical force P

Q: The results of particle size analysis for a soil sample is shown below. Plot the graduation curve

A: Given: Sieve size, mm Percentage size 63 100 20 76 6.3 65 2 59 0.6 54 0.212 47…

Q: The following shows the cross section and bending moment diagram of a two-bay continuous beam. The…

A: b=24 inch d=28 inch stirrups- #4 Maximum moment - 750 k-ft Bar size- #8 To determine- Area of…

Q: What is the degree of curve of a simple curve if its angle of deflection is 48 degrees and 30…

Q: The roof is made from what type of precast concrete element? Single Tee beam Double Tee beam Solid…

A: Precast concrete: A concrete member that is cast and cured at a location other than its final…

Q: SITUATION 1.4 In the given Figure 1.4 shows aerial view from directly above two dams. The depth of…

A: Given data in question Depth 8.50 m Width 25 m To find out Which one gives greater hydrostatic…

Q: Solve the Midspan Deflection and Slope at the left support using all six different methods. For…

A: W = 141

Q: Find the building's Period, T

Q: A boat heading N 45° E has a speed of 25 mph in still water. If the water current is moving east at…

Q: Determine the peak hour volume Determine the peak hour factor Determine the design hourly volume…

Q: 2. Two channels are welded at the top and bottom flange to form a box column and a compact section…

A: Given, L = 4 m or 4000 mm K = 1 Fy = 345 MPa

Q: ALI TITT 2 kN/m 3 m B 2 m 2 m D

Q: 3. A continuous beam bridge with a structural importance coefficient of 1.1. The mid span bending…

A: GIVEN Mid span Bending Moment due to self weight , MD=500 KN-m Mid span Bending Moment due to…

Q: 13. Among the following piles, which one does not belong to displacement pile ( B. Bored pile D.…

A: Displacement piles are defined as those piles that displace the soil laterally when they are…

Q: Another method of determining the capillary rise in a soil is to use Hazen's capillary formula. The…

A: Given : Thickness of dense silt layer = 3 m Diameter = 0.01 mm γs = 26.5 kN/m3 This is a problem of…

Q: Fig. 7.2. Using joint, section or graphical method, compute the stress of members BC, GC and GF of…

Q: identify the zero force member// statics

A: The given structure is:-

Q: Design a simply supported one-way slab with a span of 4m subjected to service live load of 3kPa.…

Q: following shows the cross section and bending moment diagram of a two-bay continuous beam. The beam…

A: b=24 inch d=28 inch stirrups- #4 Maximum moment - 750 k-ft Bar size- #8 To determine- No. of bars

Q: The 222000-lb space-shuttle orbiter touches down at about 238 mi/hr. At 202 mi/hr its drag parachute…

A: Given: Initial speed Vo =238 mi/hr, Velocity while chute deployment, V1 = 202 mi/hr, final velocity,…

Q: Design a rectangular beam with the corresponding loadings. Solve for the shear and moment diagram to…

A: f'c=28.7 MPafs=278 MPaDiameter of bars=12 mmb=0.5 dn=EsEc=9

Q: 2) What is quiet foundation and where is it used? explain it's construction procedure 3) what is…

A: (2) Concept- Quiet Foundation and its uses- In order to carry and distribute concentrated loads,…

Q: 14. If there are piles in a pile group foundation, the pile group effect coefficient n refers to ( )…

A: The correct answer is option A

Q: The depth of the flow in an alluvial channel is 1.5 m. If critical velocity ratio is 1.1, and…

A: Given- Depth of flow y=1.5 m, Critical velocity ratio m=1.1 n=0.018 Critical velocity=?

Q: A 14-inch square reinforced concrete column with tied transverse reinforcement is being considered…

A: To find the maximum permissible area of of vertical reinforcement provided that the, Column area =…

Q: For the beam shown in Fig.1, draw the influence lines for: i-The shear and bending moment at point…

A: Solution: i) ILD for the shear force at C: Ordinate at A = +l1l=+510=+0.5 Ordinate at B and D = 0…

Q: Compute the x-component of the resultant of the concurrent forces shown in N. P1 = 218 N, P2 = 394…

A: Given: P1= 304N, P2=218N P3=394N

Q: 1- Why are there standard specifications for bricks? 2- And what happens if the bricks fail to meet…

A: Reference : ASTM American Society Testing Materials To determine : 1. Standard specifications 2.…

Q: 1. What is the reaction at Support A? a. 4,000 lbs b. 5,000 lbs c. 6,000 lbs 2. What is the…

A: To find : 1. reaction at A 2. force in member…

Q: ation 1 A 500 cubic-centimeter solid having a specific gravity of 2.05 is submerged in two-liquid…

A: Given Volume of solid Vs=500 cm3Specific gravity of solids s.gsolid=2.05Specific gravity of mercury…

Q: Problem:5: Determine the horizontal and vertical reactions 60k > 3 6' 60k

A: Given data : A problem of structure analysis.

Q: 30 KN/m 6 m

A: Given To Find Maximum deflection of beam

Q: A 6-meter simply supported beam carries a total uniform factored load of 30kN/m distributed…

A: Given: Factored load = 30 kN/m d = 500 mm b = 300 mm h = 650 mm fyt = 286 MPa fc = 21 MPa L = 6 m

Q: Q1/ For an urban Highway, if the Average Annual Daily Traffic is (11000 v/d) in 2021and the annual…

Q: Consider a 304.8mm section of a single-riveted lap joint made up with plates of 6.35mm thickness and…

A: The given data is as follows: Width of plate=304.8 mmThickness of each plate=6.35 mmNumber of…

Q: The gate AB is 4.60 m long and 2.4 m wide perpendicular to the paper and is hinged at A with a stop…

Q: TRUSS 1 2) How many zero-force members are there in the following truss? M Trussl Truss 2 1 2 E ( 2…

A: Brief concept introduction- Zero force members- Zero-Force Members are those structural members that…

Q: Explain the terms human cognitive and perceptual capabilities and how they impact on safe design of…

A: Brief concept introduction- Human cognitive- It is the process of learning and understanding…

Q: Calculate the lag distance for a design speed of 65 km/hr assuming the coefficient of friction as…

A: Given- Speed V=65 km/hr, Reaction time t=2.5 s, Lag distance D=?

Q: Which of the terms is least likely to belong O simple curve O combined curve O reversed curve O…

Concept explainers

Mechanics of Solids

It is the study of the behavior of solid materials, their characteristics under various circumstances such as variation in external forces, temperature, and other internal factors. It is one of most important study in the field of engineering science, especially chemistry and mechanical engineering. In rigid body, the idealization of the solid body in which deformation is neglected. Deformation is known as the force acting on the solid state system which exerts change in its shape of the body but it continues to be at rest or in a uniform motion but it cannot accelerate. But those solid systems do have elasticity, compressibility and can be bent. This field is very vast since there are wide range of materials around us.

Question

A 3 ft. diameter log (sp.gr.= 0.82) divides two
shallow ponds as shown.
3
12
R₂0
Pr
Rx
:D
Fi
Ry
F₂
12
1.5
Compute the net vertical reaction at point
C if the log is 12 ft. long.
Compute the horizontal reaction at point C.
Compute the direction of the resultant
force w/ the horizontal at point C.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Kindly Solve Sub-Part d. d. Depth of water above the weir if P = 1.2m
Hydraulics (Metacentric Height) A crane is 18 meters long, 9 meters wide, and 3 meters high. The weight of the barge and crane lies on the vertical centerline 1.8m from the bottom of the barge for any position of the crane. Determine the maximum horizontal distance that the crane could swing a load of 11,000kg out to one side from the centerline of the barge at deck level so that no part of the base of the scow may leave the water. Note: Use 4 decimal places please show FBD and complete solution
The floor system used in a school classroom consists of a 4-in. reinforced stone concrete slab. Set a = 10 ft, b = 15 ft. What is the reaction at point H in kips?
Verticle load is 258 kN as opposed to 25*8kN - Apologies
A GRAVITY DAM HAS BASES 5m AND 15m. IT SUPPORTS WATER ON THE SIDE WITH OVERFLOW OF 0.3m. NEGLECTING HYDROSTATIC UPLIFT AND EFFECT OF WATER ON THE DOWNSTREAM, FIND THE LOCATION OF REACTION, R, FROM THE HEEL OF THE DAM IF F = 1000 kN. USE UNIT WEIGHT OF CONCRETE = 23 kN/m3
(b) A horizontal pipe is diverted upwards with an angle of 25 degrees. Water enters with a velocity of 4.5 ms-1 and exits upwards. The pipe entrance has a diameter of 200 mm and increases two times at the outlet. The inlet gauge pressure reads 80 kPa. If the difference vertical distance between inlet and outlet is 0.4 m, calculate the magnitude and direction of the resultant force on the pipe bend. Neglect energy losses and take the volume of water to be 0.18 m3
3. A triangular gutter is constructed by bending a strip of G.I. sheet in the middle. Find the angle between the sides when the carrying capacity is maximum.
A closed rectangular tank measuring 4 m long, 8.89m wide, and 3m high is filled to a depth of 1.8m with oil (SG=0.8). The tank is attached to a truck that is traveling horizontally at 9.81m/s^2. Determine the allowable force (kN)at the rear wall of the tank.
The dimensions of a 9-m-high warehouse areshown in Figure P2.12. The windward and leeward windpressure profiles in the long direction of the warehouseare also shown. Establish the wind forces based on thefollowing information: basic wind speed = 40 m/s, windexposure category = C, Kd = 0.85, Kzt = 1.0, G = 0.85,and Cp = 0.8 for windward wall and −0.2 for leewardwall. Use the Kz values listed in Table 2.4. What is thetotal wind force acting in the long direction of thewarehouse?
A vertical conical pipe has diameter 1.5 ft at the top and 3.0 ft at the bottom and 60 ft long. The friction loss is 10 ft for flow in either direction when the velocity at the top is 30 fps and the pressure head there is 6.5 ft of water. Find the pressure head in ft at the bottom when the flow is upward. a.69.6 b.58.0 c.89.6 d.46.0
A 4-ft-diameter log (sg. = 0.82) divides two shallow water as shown in the figure. Compute the horizontal reaction at point C.
Determine the magnitude (N) of the horizontal component of the reaction at point A if, F=500N, a=0.1m, b=2m, r=1.5m and d=30degrees