Indicate the voltage reading of the voltmeter below. VOLTS2.VhensWhat is the302010reading?201003015040200105025050DCA VfSATTERYPRITECTIONW-375Proper Pointer Position1000 ACVA. Indicate the resistance reading of the ohmmeter below.Direction: WRITE YOUR READING AT THE SPACE PROVIDED.II. READING AN OHMMETER00

A voltmeter is an instrument used for measuring the voltage between two points in an electric…

2. VOLTS Vhens 30 20 10 What is the 50 reading? 2. 10 50 20 100 30 150 40 200 10 50 250 50 DCA Vf EAN 4HA mA: BATTERY FUSE & DIODE PRIDECTION KC RANGE 50 2 W-375 Proper Pointer Position 1000 ACV II. READING AN OHMMETER A. Indicate the resistance reading of the ohmmeter below. Direction: WRITE YOUR READING AT THE SPACE PROVIDED.

2. VOLTS Vhens 30 20 10 What is the 50 reading? 2. 10 50 20 100 30 150 40 200 10 50 250 50 DCA Vf EAN 4HA mA: BATTERY FUSE & DIODE PRIDECTION KC RANGE 50 2 W-375 Proper Pointer Position 1000 ACV II. READING AN OHMMETER A. Indicate the resistance reading of the ohmmeter below. Direction: WRITE YOUR READING AT THE SPACE PROVIDED.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.2P: The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where...

See similar textbooks

Similar questions

The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where R1 and R2 are the resistances at temperatures T1 and T2, respectively, and is known as the temperature coefficient of resistance. If a copper wire has a resistance of 55 at 20C, find the maximum permissible operating temperature of the wire if its resistance is to increase by at most 20. Take the temperature coefficient at 20C to be =0.00382.
What is CEMF?
What do the following abbreviations stand for? a. SPST b. SPDT c. DPST d. DPDT e. NO f. NC
Suppose we include the lead resistance in the calculation of temperature for a class A RTD. If R3 = 1000 ohms, Ra = 18 ohms, V0 = 1.80 volts, and V = 5 volts. Including the tolerances, what is the highest temperature you could measure in °C? (Type in a two-decimal number)
3. Given: VS1: 18 voltsVS2: -1 voltsRB1: 1000 ohmsRB2: 6500 ohmsRB3: 8000 ohmsRB4: 5000 ohmsB=beta: 75RE: 540 ohmsVE: ? volts
Step-by-step with explanation. B) The interface shown can be used for low-current LEDs. Assume the LED voltage drop is 2.5 V. The resistor is 5Kohm. When the software outputs a high, the voltage on PPO becomes 4.89 V. When the software outputs a low, the voltage on PPO becomes 0.4 V. What is the LED current when the LED is on? (Vdd=+5V)
If R0= 44 milliohms and Ri= 736 ohms, what is R1 , R2, R3 in the equivalent circuit????
What is the Purpose of RXKL1 in Power System. (Explain Briefly)
. a) Calculate and plot the current flowing through the pn junctions of device #2 on your 3311 wafer as a function of voltage over the range of -3 volts to plus 1.5 (or so) volts on a linear scale. b) plot the I-V curve for the forward voltage on a log scale. c) What voltages correspond to 10 A/cm2, 100 A/cm2, 1000 A/cm2, 10,000 A/cm2 and 100,000 A/cm2? d) What is the current and current density when the applied voltage is equal to the built-in voltage? e) what are your thoughts on applying a voltage greater than the built-in voltage to a pn junction diode?
If we were to connect a voltmeter directly to an ohmmeter, what would you expect to see the ohmmeter register, for resistance between its test leads?
why basic occupational Safety and HEalth important to study in ELectrical engineering. ans it in 30 mins
1- If we use 5000 μF, we can get a very low ripple voltage. But this is so bad and this a disadvantage, why? 2- What happens if we use a very small resistance (few Ohms) or big resistance (100 kOhms) ?