2.1 A well-insulated, frictionless piston-cylinder assembly is connected by a valve to an air supply line at 8 bar, as shown in the figure. Initially, the air inside the cylinder is at 1 bar and 300°K and the piston is located 0.5 m above the bottom of the cylinder. Atmospheric pressure is 1 bar and the diameter of the piston face is 0.3 m. The valve is opened and air is admitted slowly until the volume of air inside the cylinder has doubled. Calculate a) the work done in kJ, and b) the final mass in kg of the air inside the cylinder for a supply temperature of 300°K. Air supplv line

2.1 A well-insulated, frictionless piston-cylinder assembly is connected by a valve to an air supply line at 8 bar, as shown in the figure. Initially, the air inside the cylinder is at 1 bar and 300°K and the piston is located 0.5 m above the bottom of the cylinder. Atmospheric pressure is 1 bar and the diameter of the piston face is 0.3 m. The valve is opened and air is admitted slowly until the volume of air inside the cylinder has doubled. Calculate a) the work done in kJ, and b) the final mass in kg of the air inside the cylinder for a supply temperature of 300°K. Air supplv line

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

) Two boilers, one with superheater(B1) and other without superheater(B2) are delivering equal quantities of steam into a common main. The pressure in the boiler and main is 20 bars. The temperature of the steam from a boiler with a superheater is 350oC and temperature of the steam in the main is 250oC. The steam in B2 is wet steam at 20oC. i) Draw a sketch of the problem with all thermodynamic properties from steam table shown on the sketch. ii) Determine the quantity of steam supplied by the other boiler. Take the heat capacity of steam, Cps = 2.25KJ/Kg.hgas= hg + Cps (Tsap-Tsat)
A pressure cooker operates by cooking food at a higher pressure and temperature than is possible at atmospheric conditions. Steam is contained in the sealed pot, with a small vent hole in the middle of the cover, allowing steam to escape. The pressure is regulated by covering the vent hole with a small weight, which is displaced slightly by the escaping steam. Atmospheric pressure is 1 bar, the vent hole area is 7mm2, and the pressure inside should be 2.75 bar. What is the mass in kg of the small weight?
Air within a piston-cylinder assembly executes a Carnot heat pump cycle, as shown in the figure below. For the cycle, TH = 600 K and TC = 300 K. The energy rejected by heat transfer at 600 K has a magnitude of 1000 kJ per kg of air. The pressure at the start of the isothermal expansion is 325 kPa. Assuming the ideal gas model for the air, determine: (a) the magnitude of the net work input, in kJ per kg of air, and (b) the pressure at the end of the isothermal expansion, in kPa.
A piston and cylinder device contains 0.15 kg of water at 25◦C (state 1). As shown in the figure, the piston weighs 500 N and has a cross-sectional area of 0.01 m2. Atmospheric pressure is 100 kPa. Heat is transferred to the cylinder from a reservoir at 200◦C, raising the piston. When the piston touches the stops, the volume inside the cylinder is Vmax= 0.165 m^3 (state 2). Heat continues to be transferred until the control mass reaches the boundary temperature (state 3). Determine: a) The initial pressure of the water (kPa) b) The temperature (Celsius) when the piston hits the stops c) The total work (kJ) d) The total heat transfer (kJ) e) The total entropy production for the entire process (kJ/K)
In an air compressor, the compression takes place at constant internal energy, and 50 kJ of heat is rejected to the cooling water for every one kilogram of air. Find the work required for the compression. 2- In a compression stroke of a gas engine, the work done on the gas by the piston is 70 kJ and the heat rejected to the cooling water is 42 kJ. Find the change of the internal energy. Stating whether it is gain or lost. 3- A mass of gas with an initial internal energy of 1500 kJ, is contained in a cylinder which has perfectly thermal insulated. The gas is allowed to expand behind a piston until its internal energy is 1400 kJ. Calculate the work done by the gas. If the expansion follows a lawPV2=C and the internal energy is changed. The initial pressure and volume are 28 bar and 0.06 m3 respectively. Calculate the final pressure and volume.
1.1 Determine the electrical power supplied to a boiler when the temperature of the entering water is 20 C and the exiting temperature is 89 C. The flow of.the pressured water is 2 Kg/s. There is a negligible pressure drop through this boiler and it operates at a constant pressure of 3 bars. The specific heat is c = 4,370 J/(Kg K). There is a 1.5(105 ) W rate of heat loss from the boiler during this process to a surrounding at 293.2 k. Consider steady state conditions. 1.2 Calculate the total rate of entropy production in Problem 1.1. 1.3 Calculate the total rate of exergy destruction (W) in Problem 1.1. The dead state temperature is 293.2 K and pressure is 1 bar. 1.4 Calculate the mass flowrate of fuel (natural gas, CH4) required to heat the water flow to the conditions of problem 1.1 if the electrical heating device is replaced with a gas fired boiler. The high heating value (HHV) of the fuel is 50.02 MJ/kg 1.6 The utility providing the electricity to the boiler in problem 1.1 uses…
Air at 20°C and 7 bar is contained in a rigid tank of 0.57 m3 volume capacity. The tank is provided with a valve that opens at a pressure of 8.5 bar and remains open until the pressure drops to 8.15 bar. Determine: (a) Air temperature just before the valve opens (b) Mass of air lost due to fire. Assuming: A fire occurs and causes the valve to open and the temperature of the air remains constant during discharge and air in the tank behaves as an ideal gas.
The Figure shows a solar collector panel embedded in a roof. The panel, which has a surface area of 24 ft2, receives energy from the sun at a rate of 200 Btu/h per ft2 of collector surface. Twenty-five percent of the incoming energy is lost to the surroundings. The remaining energy is used to heat domestic hot water from 90 to 120°F. The water passes through the solar collector with a negligible pressure drop. Neglecting kinetic and potential effects, determine at steady state how many gallons of water at 120°F the collector generates per hour.
1.1 Determine the electrical power supplied to a boiler when the temperature of the entering water is 20 C and the exiting temperature is 89 C. The flow of.the pressured water is 2 Kg/s. There is a negligible pressure drop through this boiler and it operates at a constant pressure of 3 bars. The specific heat is c = 4,370 J/(Kg K). There is a 1.5(105 ) W rate of heat loss from the boiler during this process to a surrounding at 293.2 k. Consider steady state conditions. Calculate the mass flowrate of fuel (natural gas, CH4) required to heat the water flow to the conditions of problem 1.1 if the electrical heating device is replaced with a gas fired boiler. The high heating value (HHV) of the fuel is 50.02 MJ/kg. Calculate the exergy destroyed in the process described by problem 1.4. The exergy of the fuel entering this process is 51.82 MJ/Kg. The dead state temperature is 293.2 K and pressure is 1 bar. The products of combustion leave this process at the dead state. Asnwer: The…
1.1 Determine the electrical power supplied to a boiler when the temperature of the entering water is 20 C and the exiting temperature is 89 C. The flow of.the pressured water is 2 Kg/s. There is a negligible pressure drop through this boiler and it operates at a constant pressure of 3 bars. The specific heat is c = 4,370 J/(Kg K). There is a 1.5(105 ) W rate of heat loss from the boiler during this process to a surrounding at 293.2 k. Consider steady state conditions. Calculate the mass flowrate of fuel (natural gas, CH4) required to heat the water flow to the conditions of problem 1.1 if the electrical heating device is replaced with a gas fired boiler. The high heating value (HHV) of the fuel is 50.02 MJ/kg. Calculate the exergy destroyed in the process described by problem 1.4. The exergy of the fuel entering this process is 51.82 MJ/Kg. The dead state temperature is 293.2 K and pressure is 1 bar. The products of combustion leave this process at the dead state. I already figured…
A rigid tank of volume 0.5 m^3 is initially evacuated.a tiny hole develops in the wall, and air from the surrounding at 1 bar , 21 degree Celsius leaks in.eventually, the pressure in the tank reaches 1 bar .the process occur slowly enough that heat transfer between the tank and the surrounding keeps the temperature of the air inside the tank constant at 21 degrees Celsius. Determine the amount of heat transfer.
Determine the electrical power supplied to a boiler when the temperature of the entering water is 20 C and the exiting temperature is 89 C. The flow of.the pressured water is 2 Kg/s. There is a negligible pressure drop through this boiler and it operates at a constant pressure of 3 bars. The specific heat is c = 4,370 J/(Kg K). There is a 150W rate of heat loss from the boiler during this process to a surrounding at 293.2 k. Consider steady state conditions.Calculate the total rate of entropy production in