2.12 An iron-constantan thermocouple is to be used to measure temperatures between 0 and 400°C. What will be the non-linearity error as a percentage of the full-scale reading at 100°C if a linear relationship is assumed between e.m.f. and temperature? e.m.f. at 100°C = 5.268 mV; e.m.f. at 400°C=21.846 mV

2.12 An iron-constantan thermocouple is to be used to measure temperatures between 0 and 400°C. What will be the non-linearity error as a percentage of the full-scale reading at 100°C if a linear relationship is assumed between e.m.f. and temperature? e.m.f. at 100°C = 5.268 mV; e.m.f. at 400°C=21.846 mV

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.31P: Consider two interconnected voltage sources connected by a line of impedance Z=jX, as shown in...

See similar textbooks

Similar questions

Discuss Potential barriers of combined heat and power (CHP).
(a) What are the voltages at vC1 and vC2 in the circuitas shown = −1.6 V if IEE = 2.0 mA,RC = 350 , and VREF = −1.25 V? (b) RedesignIEE and RC in the current switch described in part(a) to operate at one-fifth of the power with the samevoltages.
What is the maximum length in km for a 3 phase T.L having copper conductor of 0.775 cm2 crass section over which 200 KW at unity power factor and at 3300 V are to be delivered, the efficiency if T.L is 90%, take specific resistance as 1.725 μΩ cm
Question : Explain the concepts of lattice matched hetero-structure. Don’t copy other works. Sub:Optoelectronic Dept: EEE
Since R1=18.10Kohm, R2=67.58Kohm, RC= 1.08Kohm, RE= 3.23Kohm, VCC=14.00V, Beta=241.00 in the circuit given in the figure, calculate the IC current by doing a complete analysis. When performing your operations, 2 steps will be taken after the point. choose the closest one from the stylish ones according to the +/-10% margin of error. There is only 1 correct answer to the question.
how to derive this formula? Bdc= Ic/Ib=hFE
For flowing table draw occ and air gap at 1200rpm Note the drawing must be handwritten without using a computer I will not accept the solution because if using computer give scale ; x-acis =1cm ,0.2A y-axis= 30 cm using give sc:
A motor,the input to which is 20kW at 220V,is supplied by a two-core cable.400m long.If the power lost in the cable Is not to exceed 5% of the motor Input . Calculate the minimum permissible C.S.Area of the cable conductor What will be the voltage at the feeding point ? Assume the resistivity of the conductor at working temperature to be 0.02 microohm/m
= A Q.1): Assume that a decision is taken ordering all houses and establishments in a community to use kitchen grinders for food waste disposal to the waste water collections system , Discuss and evaluate the important mpacts on:.. .......................................................... Mgt ssesttsseseesanansstiasianevanunsssser( 20 IATKS) a. Solid wastes generation rate physical and chemical composition and characteristic. b. On -site handing and storage processes. &G c. Collection facilities = 3 d. Environmental and public health problems 23 e. On disposal by landfill , incineration or composting Sy 0D M)
write down the formulae for 3-phase fully controlled,full wave rectifier with inductive load for the following parameters: Average DC voltagerms voltagepeak inverse voltagerms currentaverage DC currentefficiencyfiring angleextinction anglepower outputpower inputform factorripple factordistortion factortotal harmonic distortiondisplacement factorpower factor of rectifier. Please answer all subpart...
Q ) For the full- wave uncontrolled rectifier circuit supplying a series resistive Thesupply voltage is v =300 sinωt , the supply frequency is 50 Hz and the loadparameter values are: R =05 Ω,a) Sketch the diagram of electrical circuitb) Sketch the load voltage and current waveforms .c) Calculate the load currentd) Calculate the average DC load voltage Vdc .e) Calculate the supply power to the loa
A) What is an emf of self-induction? a) when there is an induced emf in a circuit due to a change of current in the circuit itself b) when there is an induced emf in a circuit due to a change of current in an adjacent circuit (one within magnetic reach) B) Under what conditions of current flow is a self-induced ernf produced? a) whenever the circuit is energized b) whenever the circuit is de-energized c) whenever the amount of current flow in the circuit varies d) all of the above C) What is the direction of a self-induced emf in relation to any change in current? a) the same direction as the current flow that caused it b) the opposite direction as the current flow that caused it c) may be either "a" or "b" d) neither "a" nor "b" D). In an inductive circuit, does the inductance have any effect on the flow of a steady current? a) yes b) no