2.3 The floor system of a gymnasium consists of a 130-mm-thick concrete slab resting on four steel beams (A = 9,100 mm²) that, in turn, are supported by two steel girders (A = 25,600 mm²), as shown in Fig. Determine the dead loads acting on beam BF and girder AD. Steel floor beam (A = 9,100 mm²) A 10 m E B Steel girder (A = 25,600 mm²) DSteel C I I F G 3 at 5 m = 15 m H column 130 mm concrete slab

2.3 The floor system of a gymnasium consists of a 130-mm-thick concrete slab resting on four steel beams (A = 9,100 mm²) that, in turn, are supported by two steel girders (A = 25,600 mm²), as shown in Fig. Determine the dead loads acting on beam BF and girder AD. Steel floor beam (A = 9,100 mm²) A 10 m E B Steel girder (A = 25,600 mm²) DSteel C I I F G 3 at 5 m = 15 m H column 130 mm concrete slab

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The floor system of a gymnasium consists of a 130-mm-thick concrete slab resting on four steel beams (A = 9,100 mm2) that, in turn, are supported by two steel girders (A = 25,600 mm2), as shown in Figure. Determine the dead loads acting on beam BF and girder AD
The floor system of a gymnasium consists of a 130-mm-thick concrete slab resting on four steel beams (A=9,100 mm2) that, in turn, are supported by two steel girders (A=25,600 mm2), as shown below. Determine the point load acting on girder AD at point C.
The floor system of a gymnasium consists of a 130-mm-thick concrete slab resting on four steel beams (A = 9,100 mm2) that, in turn, are supported by two steel girders (A = 25,600 mm2), as shown in the figure. Determine the dead loads acting on beam BF and girder AD. Question 1: What is the total dead load of girder AD in kN/m?
The floor system of a gymnasium consists of a 130-mm-thick concrete slab resting on four steel beams (A=9,100 mm2) that, in turn, are supported by two steel girders (A=25,600 mm2), as shown below. Determine the live load acting on the beam BF.
The floor system of an apartment building consists of a 4-inch-thick reinforced concrete slab resting on three steel floor beams, which are in turn supported by two steel girders, as shown below. The areas of cross section of the floor beams and the girders are 18.3 in.2 and 32.7 in.2, respectively. Determine the live load acting on beam CD.
The floor system of an apartment building consists of 100mm thick reinforced concrete slab (unit weight = 23.6 KN/m^3) resting on three steel floor beams 3.0 meters on centers. Calculate the total dead load in KN/m due to slab for a single floor beam. Assume one-way slab.
The floor system of a building consists of a 5 in. thick reinforced concrete slab resting on four steel floor beams, which in turn are supported by two steel girders, as shown in Fig. 2.7(a). The cross-sectional areas of the floor beams and the girders are 14.7 in and 52.3 in , respectively. Determine the dead loads acting on the beams CG and DH and the girder AD.
shows the floor framing plan of a reinforced concrete building. All beams are 300 mm x 600 mm. The properties are as follows: slab thickness = 100 mm; super imposed dead load = 3 kPa; live load = 4.8 kPa; concrete unit weight = 24 kN/m3. The columns at E and H are deleted thus girder BEHK alone supports beam DEF at E and beam GHI at H. Calculate the total ultimate load in kN concentrated at E induced by beam DEF using tributary area method.
Given: Figure 2 shows the cross section of a wood frame building.Find: (a) Roof dead load D in psf on a horizontal plane; (b) Wall D in psf of wall surface area; (c)Wall D in lb/ft of wall; (d) Basic (i.e., consider roof slope but not tributary area) unit live load, Lr,in psf; ; and (e) Basic unit roof Lr in psf if the slope is changed to 4/12.
The floor system of a gymnasium consists of a 130- mm-thick concrete slab resting on four steel beams (A = 9,100 mm2) that, in turn, are supported by two steel girders (A = 25,600 mm2), as shown in Fig. P2.7. Determine the dead loads acting on beam BF and girder AD.
The floor system of an apartment building consists of a 100-mm-thick reinforced concrete slab resting on three steel floor beams, which in turn are supported by two steel girders, as shown in the Figure. The areas of cross section of the floor beams and the girders are 11,800 mm^2 and 21,100 mm^2, respectively. Determine the dead loads acting on the beam CD and the girder AE.
The roof system of an office building consists of a 4-in.- thick reinforced concrete slab resting on four steel beams (A ¼ 16:2 in.2), which are supported by two steel girders (A = 42:9 in.2). The girders, in turn, are supported by four columns, as shown in Fig. P2.8. Determine the dead loads acting on the girder AG.