PLEASE SOLVE THE QUESTION FROM TILL D!! 24 ka20 V32 kn10 knFigure 2- Probiem 2For the circuit shown above, the capacitor Cis initially uncharged when te0. The switch is latermoved to position 1 at t-0. You may assume that the switch remains in position 1 for a very longtime. Using a suitable analysis technique determine:(a) The initial capacitor current and voltage values when the switch is at position 1.(b) The initial voltage across the 24 ka resistor when the switch is at position 1.() The final capacitor current and voltage values when the switch is at position 1.If alter a long time the switch is moved to position 2. where it remains for an infinite amount oftime, determine:(d) The initial capacitor current and voltage values when the switch is at position 2(e) The initial voltage across the 10 kl resistor when the switch is at position 2.() The final capacitor current and voltage values when the switch is at position 2.

Since initially the switch had been in the position(1) for a long time, therefore the capacitor is…

20 V 32 km 10 ka Figure 2- Problem 2 For the circuit shown above, the capacitor Cis initially uncharged when te0. The switch is later moved to position 1 at t-0. You may assume that the switch remains in position 1 for a very long time. Using a suitable analysis technique determine: (a) The initial capacitor current and voltage values when the switch is at position 1. (b) The imitial voltage across the 24 ki resistor when the switch is at position 1. (c) The final capacitor current and voltage values when the switch is at position 1. If alter a long time the switch is moved to position 2. where it remains for an infinite amount of time, determine: (d) The initial capacitor current and voltage values when the switch is at position 2. (e) The initial voltage across the 10 kl resistor when the switch is at position 2. (0 The final capacitor current and voltage values when the switch is at position 2. 26

20 V 32 km 10 ka Figure 2- Problem 2 For the circuit shown above, the capacitor Cis initially uncharged when te0. The switch is later moved to position 1 at t-0. You may assume that the switch remains in position 1 for a very long time. Using a suitable analysis technique determine: (a) The initial capacitor current and voltage values when the switch is at position 1. (b) The imitial voltage across the 24 ki resistor when the switch is at position 1. (c) The final capacitor current and voltage values when the switch is at position 1. If alter a long time the switch is moved to position 2. where it remains for an infinite amount of time, determine: (d) The initial capacitor current and voltage values when the switch is at position 2. (e) The initial voltage across the 10 kl resistor when the switch is at position 2. (0 The final capacitor current and voltage values when the switch is at position 2. 26

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter10: Direct-current Circuits

Section: Chapter Questions

Problem 96CP: Consider the circuit below. The capacitor has a capacitance of 10 mF. The switch is closed and after...

See similar textbooks

Similar questions

Consider the circuit below, (a) What is the initial current through resistor R2? when the switch is closed? (b) What is die current through resistor R2 when the capacitor is fully charged, long after die switch is closed? (c) What happens if the switch is opened after it has been closed for some rime? (d) If the switch has been closed for a time period long enough for the capacitor to become fully charged, and then the switch is opened, how long before the current through resistor R1 reaches half of its initial value?
An electronic apparatus may have large capacitors at high voltage in the power supply section, presenting a shock hazard even when the apparatus is switched off. A “bleeder resistor" is therefore placed across such a capacitor, as shown schematically in Figure 21.50, to bleed the charge from it after the apparatus is off. Why must the bleeder resistance be much greater than the effective resistance of the rest of the circuit? How does this affect the time constant for discharging the capacitor?
Figure 21.55 shows how a bleeder resistor is used to discharge a capacitor after an electronic device is shut off allowing a person to work on the electronics with less risk of shock, (a) What is the time constant? (b) How long will it take to reduce the voltage on the capacitor to 0.250% (5% of 5%) of its full value once discharge begins? (c) If the capacitor is charged to a voltage V0through a 100-O resistance, calculate the time it takes to rise to 0.865V0(This is about two time constants.)
Integrated Concepts If you wish to take a picture of a bullet traveling at 500 m/s, then a very brief flash of light produced by an RC discharge through a flash tube can limit blurring. Assuming 1.00 mm of motion during one RC constant is acceptable, and given that the flash is driven by a 600F capacitor, what is the resistance in the flash tube?
The switch S in Figure 20.27 is closed at t = 0 and the current at a reference time tref 0 is Iref. If the circuit is changed as, described below and the switch is again dosed at t = 0, determine whether the current I at the same time would be greater than, less than, or equal to the original value of Iref. Indicate your answers wilt G. L. or E, respectively. (a) Both the battery voltage and the resistance R are doubled. (b) The inductance L b doubled. (c) The battery voltage . the resistance R, and the inductance L are each doubled. Figure 20.27 A series RL circuit. As the current increases toward its maximum value, the inductor produces an emf that opposes the increasing current.
Consider the circuit in Figure 21.29 and assume the batter has no internal resistance. (i) Just after the switch is closed, what is the current in the battery? (a) 0 (b) /2R (c) 2/R (d) /R (e) impossible to determine (ii) After a very long time, what is the current in the battery? Choose from the same choices.
A 240-kV power transmission line carrying 5.00x102. A is hung from grounded metal towers by ceramic insulators, each having a 1.00x 109- resistance. Figure 21.51. (a) What is the resistance to ground of 100 of these insulators? (b) Calculate the power dissipated by 100 of them, (c) What fraction of the power carried by the line is this? Explicitly show how you follow the steps in the Problem-Solving Strategies for Series and Parallel Resistors.
A circuit contains a D-cell battery, a switch, a 20- resistor, and three 20-mF capacitors. The capacitors are connected in parallel, and the parallel connection of capacitors are connected in series with the switch, the resistor and the battery, (a) What is die equivalent capacitance of the circuit? (b) What is the KC time constant? (c) How long before the current decreases to 50% of the initial value once the switch is closed?
A 2.00- and a 7.50-F capacitor can be connected in series or parallel, as can a 25.0- and a 100k resistor. Calculate the four RC time constants possible from connecting the resulting capacitance and resistance in series.
Integrated Concepts A 12.0-V emf automobile battery has a terminal voltage of 16.0 V when being charged by a current of 10.0 A. (a) What is the battery’s internal resistance? (b) What power is dissipated inside the battery? (c) At what rate (in °C/min ) will its temperature increase if its mass is 20.0 kg and it has a specific heat of 0.300 kcal/kg. °C, assuming no heat escapes?
Consider the circuit shown in the preceding problem. Write equations for the power supplied by the voltage sources and the power dissipated by the resistors in terms
A 500- resistor, an uncharged 1.50-F capacitor and a 6.16-V emf are connected in series, (a) What is the initial current? (b) What is the RC time constant? (c) What is the current after one time constant? (d) What is the voltage on the capacitor after one time constant?