20.a. Which of the following conductors can you install when using the pressure terminals on a receptacle? A. No. 12 solid copper B. No. 10 solid copper C. No. 14 solid aluminum D. No. 12 solid aluminum End of exam 20.b. Two switches are used to control a light from either end of a hallway. The two conductors that directly join the switches are A. stranded. B. travelers. C. two-phase conductors. D. grounding conductors.

20.a. Which of the following conductors can you install when using the pressure terminals on a receptacle? A. No. 12 solid copper B. No. 10 solid copper C. No. 14 solid aluminum D. No. 12 solid aluminum End of exam 20.b. Two switches are used to control a light from either end of a hallway. The two conductors that directly join the switches are A. stranded. B. travelers. C. two-phase conductors. D. grounding conductors.

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter20: Special-purpose Outlets For Ranges, Counter-mounted Cooking Unit , And Wall-mounted Oven

Section20.2: Wall-mounted Oven Circuit And Free-standing Range

Problem 14R

See similar textbooks

Similar questions

15. Which of the following conductors in a typical separable connection plug and receptacle has a firstmake, last-break feature?A. The neutral grounded conductorB. The equipment grounding conductorC. A center wye conductorD. The grounded delta conductor
11.a. You're installing an isolated power system in a hospital that'll serve a group of patient care areas. Whichof the following colors must be used for the wire that connects to the terminal at each receptacle that'susually reserved for the neutral conductor?A. Green with a white stripeB. Orange with a distinct stripeC. White with an orange stripeD. Red with a black stripe 11.b. The _______ is typically where the service main bonding jumper is installed or where the systembonding jumper is installed for a separately derived system.A. equipotential planeB. site-isolating deviceC. point of groundingD. isolated power system
11.a. Which of the following is a point where a grounding electrode conductor connection must be made inthe communication system?A. The flexible nonmetallic power service racewayB. The grounding electrode conductor or metal enclosure for a grounding electrode conductorC. The space opposite the service equipment enclosureD. The grounded exterior metal water piping system within six feet of the point where it enters the building11.b. The equipment grounding conductor of a pump motor for a swimming pool must be grounded with asolid copper conductor that's no smaller thanA. AWG 8.B. AWG 12.C. AWG 10.D. AWG 6.
10.a. Which of the following is a condition of the exception that allows the grounded conductor of feeders tobe used for grounding at separate buildings or structures?A. There are common electrically continuous metallic paths between the feeder source and the destination at the structure served.B. There are common electrically continuous nonmetallic paths between the equipment grounding conductor and the destinationat the structure served.C. An equipment grounding conductor isn't included with the supply circuit to the separate structure.D. Ground-fault protection of equipment is provided on the supply side of the feeder.10.b. A service disconnection means must be installed adjacent to, within sight of, and no more than_______ feet from a mobile home.A. 20B. 30C. 10D. 50
What is the rated ampacity per phase for six No. 3/0 THHN copper current-carrying conductors with two conductors per phase ( parallel) and all conductors installed in the same conduit? a. 280 b. 315 c. 320 d. 360 Please show work/code references to go with if possible!
5. How many system bonding jumpers normally are there for a separately derived system that's grounded? A. ThreeB. TwoC. One D. Zero 6. How many grounded neutral conductors are in a 208Y/120 volt, 3-phase, 4-wire system? A. ThreeB. TwoC. One D. Four 7. Which of the following are sometimes installed as an emergency system, legally required standby system, or optional standby power system for a building or structure? A. GeneratorsB. Surge protection devices C. Surge arrestersD. Transformers 8. If the system bonding jumper in a DC system is a screw, what color must the screw be? A. WhiteB. RedC. Orange D. Green 9. If overcurrent protection is provided in the transformer of a separately derived system, which of the following statements is correct? A. An equipment grounding conductor must be run with the conductors between the transformer and the building's disconnect. B. There's no need for service equipment or a panelboard in the separate building.C. A ground electrode must…
Seven 8 AWG copper conductors are run in conduit. Each conductor has type THHN insulation. The conduit is located in an area with an ambient temperature of 138oF. What is the ampacity of each conductors?
What is the minimum size copper grounding electrode conductor for each of the following residential electrical services? Refer to Table 250.66. The ungrounded conductors are Type THW copper. 310.15(B)(7) is only for 120/240-volt, single-phase residential services and feeders. This Section does not apply to services and feeders other than residential.
12. Which of the following statements about ground faults is true?A. They can happen if a conductive tool is dropped in an energized equipment's electrical enclosure.B. They usually occur between any grounded circuit conductor and the equipment grounding conductor.C. They can't result from human error.D. They're often normal and typically intentional.
Equipment Grounding 10. Which of the following statements about ground faults is true?A. They usually occur between any grounded circuit conductor and the equipment grounding conductor. B. They're often normal and typically intentional.C. They can't result from human error.D. They can happen if a conductive tool is dropped in an energized equipment's electrical enclosure.
Six 1/0 aluminum conductors are to be run in a conduit. Each conductor has type THWN insulation's, and the ambient air temperature is 30 degrees celcius. What is the ampacity of each conductor?
11. Which of the following statements about the use of structural steel as an equipment grounding conductor (EGC) in an AC system is correct? A. Structural steel can be used as an EGC when it's bonded at both ends.B. Structural steel isn't allowed for use as an EGC.C. Structural steel must have an EGC bonding jumper every three feet of structure. D. Structural steel can be used as an EGC bonding jumper between panelboards. 12. Which of the following statements about equipment grounding conductors is true? A. They increase voltages above ground potential on conductors and equipment enclosures during normal operation. B. Unacceptable equipment grounding conductors include conduit, tubing, and cable armor. C. They must be capable of withstanding the higher level of ground-fault current to perform their safety function. D. When they're far from their associated circuit conductors, impedance values are kept as low as possible during ground-fault conditions. 13. Imagine that…