21-45. If the shaft AB is rotating with a constant angularvelocity of w = 30 rad/s, determine the X, Y, Z componentsof reaction at the thrust bearing A and journal bearing B atthe instant shown. The disk has a weight of 15 lb. Neglectthe weight of the shaft AB.1.5 ft301 ft0.5 ftвw = 30 rad/s

Given data: Constant angular velocity, ω = 30 rad/s Weight of the disc, W = 15 lb. Radius of the…

Answered: 21-45. If the shaft AB is rotating with…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

18-37 The spool has a mass of 20 kg and a radius of gyration of = 160 mm. if the 15 kg block A is released from rest, determine the velocity of the block when it descends 600 mm.
14-59 The material hoist and the load have a total mass of 800 kg and the counterweight C has a mass of 150 kg. At a given instant, the hoist has an upward velocity of 2 m/s and an acceleration of 1.5 m/s2. Determine the power generated by the motor M at this instant if it operated with an efficiency of 0.8
15-102. The two spheres each have a mass of 3 kg and are attached to the rod of negligible mass. Determine the time the torque M = (8t) N·m where, is in seconds, must be applied to the rod so that each sphere attains a speed of 3 m/s starting from rest
Determine the speed v of the 50-Mg mass when it is just over the top of the steel post, if after impact, the maximun stress developed in the post is 550 MPa. The post has a length of L = 1 m and a cross-sectional area of 0.01 m2.Est = 200 GPa, sY = 600 MPa.
15-23. The motor exerts a force F on the 40-kg crate a shown in the graph. Determine the speed of the crate when t= 3 s and when t = 6 s. When t = 0, the rate is moving downward at 10 m/s
19-35 The 10 kg bullet having of 800 m/s is fired into the edge of the 5 kg disk as shown. Determine the angular velocity of the disk just after the bullet becomes embedded into its edge. Also, calculate the angle the disk will swing when it stops. The disk is originally at rest. Neglect the mass of the rod AB.
The spring-held follower AB has a mass of 0.5 kg and moves back andforth as its end rolls on the contoured surface of the cam, where r = 0.15 m and z =(0.02 cos 2θ) m. If the cam is rotating at a constant rate of 30 rad/s, determine theforce component Fz at the end A of the follower when θ = 30°. The spring isuncompressed when θ = 90°. Neglect friction at the bearing C.
If the cord is subjected to a horizontal force of P = 150 N, and gear is supported by a fixed pin at O,determine the angular velocity of the gear and the velocity of the 20-kg gear rack in 4 s, starting from rest. The mass of the gear is 50 kg and it has a radius of gyration of k0 = 125 mm. Assume that the contact surface between the gear rack and the horizontal plane is smooth.
14-29 The train car has a mass of 10 Mg and is traveling at 5 m/s when it reaches A. If the rolling resistance is 1/100 of the weight of the car, determine the compression of each spring when the car is momentarily brought to rest
18-9 The pendulum consists of a 10 kg uniform disk and a 3 kg uniform slender rod. If it is released from rest in the position shown, determine its angular from velocity when it rotates clock wise .
The smooth particle has a mass of 80 g. It is attached to an elastic cord extending from O to P and due to the slotted arm guide moves along the horizontal circular path r=(0.8sinθ)m. If the cord has a stiffness k= 24 N/m and an unstretched length of 0.25 m, determine the force of the guide on the particle when θ=60. The guide has a constant angular velocity θ˙=5rad/s
The wheel has a mass of 100 kg and a radius of gyration of kO = 0.2 m. A motor supplies a torque M = (40u + 900) N #m, where u is in radians, about the drive shaft at O. Determine the speed of the loading car, which has a mass of 300 kg, after it travels s = 4 m. Initially the car is at rest when s = 0 and u = 0°. Neglect the mass of the attached cable and the mass of the car’s wheels

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS