22.An incompressible fluid flows steady through two pipes a diameter 0.12 m and 0.22 m which combine to discharge in a pipe of 0.3 m diameter.lf the average velocities in the 0.12 m and 0.22 m diameter pipes are 1.5 m/s and 0.33 m/s respectively. i) Find the average velocity and discharge in lit/hr in the 0.3 m diameter pipe and ii) Draw the pipe line sketch and direction of flow of fluid.

22.An incompressible fluid flows steady through two pipes a diameter 0.12 m and 0.22 m which combine to discharge in a pipe of 0.3 m diameter.lf the average velocities in the 0.12 m and 0.22 m diameter pipes are 1.5 m/s and 0.33 m/s respectively. i) Find the average velocity and discharge in lit/hr in the 0.3 m diameter pipe and ii) Draw the pipe line sketch and direction of flow of fluid.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter10: Heat Exchangers

Section: Chapter Questions

Problem 10.19P

See similar textbooks

Similar questions

An incompressible fluid (water) flows steadily from an open tank. The elevation of point 1 is 10.0m, and the elevation of point 2 and 3 is 2.00m. The cross-sectional area at point 2 is 0.0680 m^2, at point 3 it is 0.0360 m^2. The area of the tank is very large compared to the cross-sectional area of the pipe. Assuming that Bernoulli’s equation applies, compute: (a) The discharge rate in cubic meters per second;(b) The gauge pressure at point 2.
A certain hydropower plant is being supplied by river flow of 900 cubic ft/sec and the head on the site is 200 ft. To develop maximum capacity it was proposed to install 2 turbines, one of which is 1.5 times the capacity of the other. Both turbine units are assumed to have efficiency of 85%. Determine (a) the total power developed, (b) what is the power developed by turbine #1 and by turbine #2 and (c) Rotative speed of each turbine unit assuming specific speed equal to 70 rpm.
Suppose that you are willing to determine the diameter of the water jet impinging to the sink from the kitchen tap.The tap is produced to supply three different flow rates of the low, medium, and high. For each flow rate level, waterthat comes from the tap fills the beaker with a volume of 30 mL in 10 s, 6 s, and 2 s, respectively. The outlet of the tapis 13 mm, and the distance between the tap outlet and the sink is 53 mm. Determine the diameters of the water jetimpinging on the sink at three given flow rates.
Flow Speed in a Channel The speed of water flowing in achannel, such as a canal or river bed, is governed by theManning Equation,
The mean radius of an axial flow reaction turbine is 2.6 ft. and the axial velocityis 25 ft./s. The wicket gates are turned at an angle such that relative velocity at theinlet flow makes an angle of -45° with the blade velocity. The wheel and hub radiiare 3.6 ft. and 1.6 ft., respectively. The turbine rotates at 240 rpm. If water leaves theblade in a purely axial direction, calculate H and all relevant angles.Ans: H=81.87 ft.; α1=31.8°; β2=20.93°
Find the flow rate, net head, and efficiency of the pumps if they are operating separately. Show on the graph you have drawnas a representative how you have determined by using the graph. Using the graphs, show your selection and calculations onthe graph (you can draw the graphs on excel) ÖN=5
The axial flow pump produces a discharge of 0.095 m3/sm3/s. The impeller is rotating at ωω = 110 rad/srad/s, and it has a mean radius of 75 mmmm. (Figure 1) Figure 1 of 1 Part A Determine the magnitude of the velocity of the water as it exits the blades. Express your answer to three significant figures and include the appropriate units. V2V2 = nothingnothing SubmitRequest Answer Part B Complete previous part(s) Part C Determine the magnitude of the relative velocity of the water as it flows off the blades of the impeller. Express your answer to three significant figures and include the appropriate units. (Vrel)2(Vrel)2 = 4.27ms
During a test run of a Pelton wheel turbine, the pressure at the nozzle was 2.25 MPa when water flowing in the penstock at 1.7 cubic meter/sec. The penstock diameter is 600 mm. Determine: a. The effective head in meters 255.09 231.27 241.36 b. The Water Power (WP) in kW 3,855 4,226 3,413 c. The turbine power in kW if the turbine efficiency is 80% 3,277 3,413 3,084 d. the generator output in MW if the generator efficiency is 92% 2.837 3.139 2,837
Water flows through a rubber hose 2 cm in diameter at a velocity of 4 m/s. (a) What must be the diameter of the nozzle in order that the water emerge at 16 m/s? (b) What is the rate of flow in cu.m per minute?
A centrifugal pump delivers 25 liters of water per second against a head of 10 meters and running at 1300 rpm requires 10 kW of power. Determine the discharge, head of the pump and power required if the pump runs at 1500 rpm. (Ans. 0.0288cumec or 1.73 cu.m./min , 13.31m, 15.36kw)
We want to measure the flow rate of water at 20 C by a thin plate orifice. The pipe diameter carrying the water is 20 cm and the thin-plate orifice dimater is 5 cm. A pressure drop of 70 kPa is measured between the taps. Find the flow rate and the throat velocity. [Ans.: 23 lit/s, 11.6 m/s].
Guava juice enters a pipe with an ID of 3.05 inches at a rate of 15.6 ft3 / hr, then exits through a d of 6.4 in. Calculate the velocity at the exit?