fast. Water at 21 °C flows downward in a pipe at0.37 radians inclination as shown in the figure. Themercury manometer reads h 0.119 m in heightdifference. The distance between point 1 and 2 is L0.506 m. What is the pressure difference P1-P2 inPascals? Assume the density of mercury to be 13600kgm3and 1000kgn³for water.The conversion factor between radians and degreesis 1 rad =57.29Assume the acceleration of gravity to be 9.80ms2Le radiansP1inclinationWater flowP2Mercurymanometer

Answered: Water at 21 C flows downward in a pipe…

Engineering

Mechanical Engineering

Water at 21 C flows downward in a pipe a

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: 9. The orifice in Fig. 57 is 2 in. in diameter and is sharp-edged with - 0.63 and C, = 0.97. The…

Q: A pitot tube is used for : a.measuring discharge b.average velocity c.velocity at a point…

A: We know that, pitot tube is a device used for measuring the velocity at a point. This velocity is…

Q: What is the ratio of the average velocity to maximum velocity for water flowing in a 1" schedule 40…

Q: A pressure relief valve has a power loss across the valve is 11.6 x 10 MJ/sec and flow rate of 5.22…

A: If a constant static back-pressure is greater than atmospheric, the set pressure of the pressure…

Q: Benzene flows through a 100 mm diameter pipe at a mean velocity of 3 m/s. Find discharge in liter…

A: Given Diameter, d =100 mm Velocity, V = 3 m/s Find Discharge, Q

Q: Problem 10 Water flows steadily from an open tank as shown below. The elevation of point 1 is 10.0…

A: Given data: The elevation of point 1 is 10.0 m The elevation of points 2 and 3 is 2.00 m The…

Q: The below figure shows a pump that transfers a steady stream of 35◦API crude oil from an oil tanker…

Q: I need the answer as soon as possible

A: Dear student, According to the guidelines I am allowed to answer only one…

Q: 3: Water flows through a 100 mm diameter pipe at velocity of 4.5m/sec. Find the discharge.

A: Given:d=100 mmV=4.5 m/s

Q: Water is flowing through a 2.067-in ID pipe with a velocity of 1m/s. Calculate: (a) Mass flowrate…

A: Given data Internal diameter of pipe (D) = 2.067 in = (2.067 * 0.0254) m = 0.0525 m velocity (V) =…

Q: The flow is

A: Given: In a langrangian system is defined in which individual fluid paticlesare tracked.The…

Q: 10 point 8. Water flows from section 1 to section 2, as shown. For section 1, the velocity is 2.0…

Q: Find the diameter of the pipe in mm. The discharge of the pipe is 35 lit/sec with the velocity of…

Q: Refer to Fig. X5.2.2. Assume a = 1 m, b = 4 m, and the flow to be frictionless in the siphon. Find…

A: Given: The diameter of the pipe is, d=150 mm×10-3 m1 mm=0.150 m. The value of a is 1m. The value of…

Q: 10 in discharge pipe is attached to a certain storage. The head loss from the surface to the…

A: Given:d=10 in =0.254 mHl=8 ft =2.4384 mZ1=15 ft =4.572 m

Q: Question 3) As seen in the figure, the vacuum pump provides air flow in an insulated pipe with a…

A: Given data, Calculating Mach Number at section using the given relationship: - Hence, the Mach…

Q: Find the diameter of the pipe in mm. The discharge of the pipe is 35 lit/sec with the velocity of…

A: Given Discharge , Q = 35 lit/ sec = 0.035 m3/s Velocity, v = 3.5 m/s

Q: he figure shows a siphon discharging oil (sp.gr.= 0.90). The siphon is composed of 75 mm pipe…

Q: A B PROBLEMS 10.93, 10.94 10.94 Pipes 1 and 2 are the same kind (cast-iron pipe), but pipe 2 is four…

A: Discharge water of pipe (2) Q2 is 1 cfs. Pipes are in parallel, Qe=Q1Q2hfc=hf1+hf2…

Q: A venturimeter with 75 mm diameter throat is placed in a 150 mm diameter pipeline carrying water.…

Q: Your second customer wants to determine the required electrical power, which will be used to pump…

Q: Question-1: Carbon dioxide at 20°c and a pressure of 550 kPa (abs) flows in a pipe at a rate of 0.04…

A: Given:P=550 KPaT=20°CgPQ=0.04 N/sPQ=0.04g=0.049.81μCO2=1.4*10-5 N.sm2In case of turbulent…

Q: Water is pumped thru a vertical 50mm new galvanized-iron pipe to an elevated tank on the roof of a…

Q: Oil flows full bore at a velocity of 2m/s through a nest of 16 tubes in a single pass cooler. The…

A: Given Data: The velocity of the oil is V = 2 m/s. The number of tubes is N = 16. The internal…

Q: Find the discharge of the pipe of diameter 20 mm with the velocity of water 5.25m/s in litres/sec…

Q: reservoir A is at elevation 90 m above datum, furnishes water to a 600 mm pipe which leads to a…

Q: subcooled? Determine (b) the volume flow rate, and (c) the

A: Given: Refrigerant R22 Condenser temperature=42oC Evaporating temperature =0oC To determine:…

Q: Oil is flowing at the rate of 3.14 cfs in a pipe of varying cross section. At section A, the…

A: Given data: Oil flow rate = 3.14 cfsSection A diameter = 6 inch = 0.5 ftPressure at A = 12 Psi = 12…

Q: A 12" pipe carrying 3.93 cfs connects to a 6" pipe. Find the velocity head in the 6" pipe.

A: Given: Discharge, Q=3.93 cfs (cubic feet per second) Diameter of pipe=6 inch

Q: Water at 20°C flows from Tank 1 to Tank 2 through a 2-inch, Schedule 40 pipe as shown in the figure…

A: D=Diameter of Pump=2 inch=0.0508 mQ=Flow Rate of Water=10 L/s=0.01 m3/sL=length of Pipe=100 m

Q: The pressure through a section of pipe is 21 PSI and the velocity of the fluid is 1 ft/sec. If the…

A: given data; pressure at section 1st (P1)=21PSI=144789.903pavelocity at section…

Q: Find the diameter of the pipe in mm. The discharge of the pipe is 30 lit/sec with the velocity of…

A: we know that Discharge= Area*Velocity Q= A*V Given data Q=30lit/sec =22.2kg/sec V=3.25m/s

Q: In Fig. 3, pipes I, 2, and 3 are 730+(Reg.No./100) ft of 4-in, 240+(Reg.No./100) ft of 2- in, and…

A: As per BARTLEBY rules i answer only one question,so i hope you understand.

Q: A 2-inch diameter hose is conveying water at a flow rate of 20 gpm from point A to point B. The…

A: Given: Pressure at point A: →PA=40 psi=144×40=5760 lbf/ft2 Elevation at point A from mean sea level:…

Q: compute the expected maximum velocity of flow.

Q: 5. Derive an expression for the loss of head due to : (i) Sudden enlargement and (ii) Sudden…

Q: A system total head against mean velocity curve for a particular power law liquid in a particular…

A: Pipe system curve equation ∆h=(0.03)(100n)(un)+4.0 Pump curve equation ∆h=8.0-0.2u-1.0u2 u≤1.5 m/s…

Q: QI (a) Water flows through the pipe contraction shown in Figure Q1 (a). Determine the volume flow…

A: The volume flow rate is needed to be calculated. For this , Bernoulli's principle alongwith…

Q: 3. A fire hydrant has an outlet diameter of 630 mm located 1.4 meters above the ground. If the water…

Q: Water flows at a rate of 500 gal/min through a 400-ft-long line. The first and last 100 ft of the…

A: GivenQ=500 gal/min=1.89271 m3/min=0.031545 m3/sL=400ft

Q: As seen in the figure, the vacuum pump provides air flow in an insulated pipe with a cross section…

A: Given data, Calculating Mach Number at section 1 using the given relationship: - Hence, the Mach…

Q: Water at 5°C is to be pumped from the river to the bottom of a water tower. The pump is 5 m above…

A: Given: a=5 mDa=6 inb=19.5 mDb=4 inc=4.2 mFlow rate (Q)=0.021 m3/sHead losses are:hL,a=1.2 mhL,b=4.2…

Q: Part A Let the pressure gradient in the pipe be 1400 Pa/m and the diameter of the pipe be 4.0 mm.…

Q: A prismatic vessel has two compartments A and B communicating by an orifice 0.3m square with C =…

A: Given Data Area of orifice is : Ao=0.3×0.3=0.09 m2 Coefficient of discharge is :C=0.60…

Q: Q4/ An orifice meter is used to measure the rate of flow of a fluid in pipes. The flow rate is…

Q: 7. A large tank is partly filled with water, the air space above being under pressure. A 2" hose…

Q: A reservoir supplies water as shown in Fig. 1. The pipe system consists of 6 m of pipe and two 90°…

A: In the given system hydrostatic head of the reservoir is converted into a velocity head in the pipe.…

Concept explainers

Conservation of Energy

In physics, the rule of the conservation of energy states that energy doesn’t disappear from the atmosphere; instead, it changes its form from one type to another. Energy is one of the most important physical quantities in nature, and it cannot be created or destroyed — only transformed.

Question

fast.

Water at 21 °C flows downward in a pipe at
0.37 radians inclination as shown in the figure. The
mercury manometer reads h 0.119 m in height
difference. The distance between point 1 and 2 is L
0.506 m. What is the pressure difference P1-P2 in
Pascals? Assume the density of mercury to be 13600
kg
m3
and 1000
kg
n³
for water.
The conversion factor between radians and degrees
is 1 rad =57.29
Assume the acceleration of gravity to be 9.80
m
s2
L
e radians
P1
inclination
Water flow
P2
Mercury
manometer

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

For the traditional equal-level manometer measurement inFig. E2.3, water at 20 ° C fl ows through the plug devicefrom a to b . The manometer fl uid is mercury. If L= 12 cmand h= 24 cm, ( a ) what is the pressure drop through thedevice? ( b ) If the water fl ows through the pipe at a velocityV =18 ft/s, what is the dimensionless loss coeffi cient ofthe device, defi ned by K = ∆ p /( ρ V 2 )?
A pipe inclined at 45° to the horizontal (Fig. 2) converges over a length l of 2 m from a diameterd1 of 200 mm to a diameter d2 of 100 mm at the upper end. Oil of relative density 0.9 flowsthrough the pipe at a mean velocity ?̅1 at the lower end of 2 m/s. Find the pressure differenceacross the 2 m length ignoring any loss of energy, and the difference in level that would beshown on a mercury manometer connected across this length. The relative density of mercury is 13.6 and the leads to the manometer arefilled with the oil.
(Just Question a.) A water filled pipe has water flowing at v1= 5.90 m/s in a section of pipe where the diameter is d1= 20.2 cm and the pressure is known to be P1= 7.00×104 N/m2 above atmospheric pressure. If the pipe carries the water 3.5 meters up hill without any change in diameter, what is the new absolute pressure within the pipe? After flowing up the hill described above, the pipe narrows to 80% of its original radius, what will be the new water velocity (v2) in the pipe? What will be the absolute pressure (P3) in the smaller pipe? a. What is the volume flow rate through the smaller pipe?
Q.3 A differential manometer is used to measure pressure difference between two fluid systems. Two parallel pipes carrying freshwater and seawater are connected to each other by a double u-tube differential manometer as shown in figure. Determine pressure difference between the two pipelines if h= 32cm. Also if the pressure difference between the pipes is doubled, what will be the difference in heights(h) of mercury?Take density of sea water at that location to be 1035kg/m3 and the specific gravity of the oil is 0.72. Assume all fluids are incompressible.
A manometer, shown in the figure is being used to measure the head or pressure drop across a flowmeter. The heavy fluid is mercury, with a density of 13.6 g/cm3, and the top fluid is water, with density of 1.00 g/cm3. The reading on the manometer is R = 32.7cm. Calculate the difference in kPa, answer rounded to 1 decimal place.
A pipe with unequal ends is used to transport a fluid. The pipe diameter at the larger end is 0.67 cm and the other end is 0.29 cm. The larger and smaller ends are located 9 m and 3 m, respectively, from the datum line. If the flow at the 9 m datum line is 1.48 m/s and the pressure is 5156 kN/m2, compute for the pressure, in kPa, at the smaller end. Express your answer in 3 decimal places.
Consider a soap bubble of diameter 3 mm. If the surfacetension coeffi cient is 0.072 N/m and external pressureis 0 Pa gage, what is the bubble’s internal gage pressure?( a ) - 24 Pa, ( b ) + 48 Pa, ( c ) + 96 Pa, ( d ) + 192 Pa,( e ) -192 Pa
Shown in the figure, Fluid 1 is flowing in a horizontal tube and a U-tube manometer containing Fluid 2 is connected to point 1 and 2. The specific weights for Fluid 1 and 2 are and , respectively. If the specific weight are =8.00 kN/m3, =10.00 kN/m3, and h1=0.10 m, h2=0.20 m, calculate the pressure difference between the two points, p1-p2=_________(kPa)
You are evaluating a pipe network transporting water from a large river reservoir to the citywater storage facility. According to the pipe specifications, the pressure leaving the pipe network(continuing to city storage) cannot exceed 3 psi. Given Qa, pipe diameters (Da – Dd), determinethe pressure exiting the pipe network. Do the city designers need to reconfigure the set-up. Usethe Hazen-Williams equation to determine the head losses. All pipe lengths are 200 feet long,and the pipes are made of recently installed galvanized iron. given below Flow rate and Diameter for all 4 pipes: Q_a=42 csf, D_a=4ft, D_b=3.2ft, D_c=7ft, D_d=2.1ft.
Capillary rise in the glass tube used for measuring water level isnot to exceed 0.5 mm. Determine its minimum size, given thatsurface tension for water in contact with air = 0.07112 N/m.
A water filled pipe has water flowing at v1= 5.90 m/s in a section of pipe where the diameter is d1= 20.2 cm and the pressure is known to be P1= 7.00×104 N/m2 above atmospheric pressure. a. If the pipe carries the water 3.5 meters up hill without any change in diameter, what is the new absolute pressure within the pipe? b. After flowing up the hill described above, the pipe narrows to 80% of its original radius, what will be the new water velocity (v2) in the pipe? c. What will be the absolute pressure (P3) in the smaller pipe? d. What is the volume flow rate through the smaller pipe?
The water flow between large tanks is steady and steady, and the pipe diameters are indicated in the figure. Calculate the height of ha when hb = 2 m according to the figures given in the figure.(g = 9.81 m/s2 , density of water 1000kg / m3.)