23. The programmer used three-point method to set up an accurate UF[3] on the part reference surface by sequentially recording points 1, 2, and 3 that are specified on the part reference surface for the three-points method in the robot system. If the programmer recorded three points used by the three-point method in the sequence of points 1, 3, 2 rather than point 1, 2, 3, then (a) the direction of x-axis is not changed (b) the direction of z-axis of UF[3] is changed (c) UF[3] setup is not accurate relative to the part reference surface (d) the origin of UF[3] is changed 24. The programmer preciously recorded all robot points P[n] for a robot task program. However, it is found that during the execution of the robot program, the robot TCP can't always precisely reach to each recorded point. Which of the following statements is correct: (a) The robot has poor accuracy (b) the robot has poor repeatability

23. The programmer used three-point method to set up an accurate UF[3] on the part reference surface by sequentially recording points 1, 2, and 3 that are specified on the part reference surface for the three-points method in the robot system. If the programmer recorded three points used by the three-point method in the sequence of points 1, 3, 2 rather than point 1, 2, 3, then (a) the direction of x-axis is not changed (b) the direction of z-axis of UF[3] is changed (c) UF[3] setup is not accurate relative to the part reference surface (d) the origin of UF[3] is changed 24. The programmer preciously recorded all robot points P[n] for a robot task program. However, it is found that during the execution of the robot program, the robot TCP can't always precisely reach to each recorded point. Which of the following statements is correct: (a) The robot has poor accuracy (b) the robot has poor repeatability

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Hartley Electronics, Inc., in Nashville, producesshort runs of custom airwave scanners for the defense industry.The owner, Janet Hartley, has asked you to reduce inventory byintroducing a kanban system. After several hours of analysis, youdevelop the following data for scanner connectors used in onework cell. How many kanbans do you need for this connector?Daily demand 1,000 connectorsLead time 2 daysSafety stock 12 dayKanban size 500 connectors
Briefly discuss how each of the following is used by CFD codes to speed up the iteration process: (a) multigridding and (b) artificial time
You are the mechatronics engineer of a manufacturing plant. You decide to perform an analysis on a robot arm of the assembly line with the objective of optimizing its performance. After taking several readings of the speed of the arm’s end effector, you approximate its velocity to the function given below. v(t) = -t4 + 5t3 - 7t2 + 3t + 0.22 0 =< t =< 3 where the velocity is in ms-1 Use your knowledge of differentiation to sketch the velocity-time graph, clearly marking the critical points. Using the graph sketched in (a) above, estimate the velocity when t = 1.5 s Calculate the velocity of the function when t = 1.5 s by substituting to the velocity function. Compare this value to the value you estimated in b above.
Can you walk me through using STK to verify this result? I have STK 12 for referance.
Matlab code please or just some stepping stones to help.
My professor said that I need to use the numbers as shown on the picture and make the exact graph that is also shown on the picture. But I don’t know how to put this in to MATLAB. Please send the code that makes the graph that is shown in the picture. Make it 100% exactly the same.
2. (If relevant) A clearly labeled diagram (or diagrams) clearly pertaining to your analysis with a coordinate system and relevant labels. Final answer with appropriate units and significant figures. You can use the fprintf() command in MATLAB to format numerical results A 2-3 sentence reflection on your answer. Does it make sense? Why or why not? What are some implications?
Which clause of an SQL query displays the results in a specific sequence?
Which clause of an SQL query is used to restrict the number of rows returned?
Having trouble applying the rules for simplifying this block diagram. Please explain how to simplify. Thanks!
Suppose your CFD code can handle nonelementary blocks. Combine as many blocks of Fig. as you can. The only restriction is that in any one block, the number of i-intervals and the number of j-intervals must be constants. Show that you can create a structured grid with only three nonelementary blocks. Renumber all the blocks and indicate how many i- and j-intervals are contained in each block. Add up all the cells and verify that the total number of cells does not change.
How do I input this code into MATLAB to solve this problem? Thanks!