25. A benchmark program is run on a 200 MHz processor. The executed program consists of 1 million instruction executions, with the following instruction mix and clock cycle count Instruction Type Arithmetic and logic Load and store Branch Others Instruction Count (Million) 8 4 2 4 Cycles per Instruction 1 3 4

25. A benchmark program is run on a 200 MHz processor. The executed program consists of 1 million instruction executions, with the following instruction mix and clock cycle count Instruction Type Arithmetic and logic Load and store Branch Others Instruction Count (Million) 8 4 2 4 Cycles per Instruction 1 3 4

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

Consider two microprocessors having 8-bit and 16-bit wide external data buses, respectfully. The two processors are identical otherwise and their bus cycles are the same speed. Suppose all instructions and operands are two Bytes. By what factor do the maximum data transfer rates vary? Suppose all instructions and operands are one Byte. By what factor do the maximum data transfer rates vary? Discuss your answers.
Draw the Moore and Mealy State Diagram of a Finite State Machine thatfunctions as a Binary Sequence Detector for the following sequence:a. 01011b. 101 and/or 010Obtain the State Table for each of your diagrams?
Assess the method to generate a 6.25 MHz signal using a 10-bits serial shift register operated with 50 MHz clock. Show all the necessary steps, delay calculations and workings in your answer.
A program executes 200 billion instructions. It executes on an IBM processor that has an average CPI of 3 and a clock frequency of 3.0 GHz. How many seconds does the program take to execute? What is the cycle time of this IBM processor? Assume that an ARM processor takes 10 seconds to execute the program. What is the speedup provided by the IBM processor, relative to the ARM processor?
Q3) A bit word 1010 is transmitted. Construct the even parity 7-bit hamming code for this data? If at receiver end data is received as 1000010, then check and correct the code using even parity scheme. Assume the direction of generation and checking the code from right to left?
How many address lines are required by a microprocessor to address 256KB of memory locations? If we use memory chips of the size 2048X8, how many address lines are required for selecting the chip and how many are required for uniquely identifying the location within the chip? If the clock frequency of microprocessor is 5MHz, how much time is required to execute an instruction of 10 T states?
design single Traffic light control system using D flip flop , write the state diagram and the state table and the truth table of design ?
Assume a three-story hospital is built at Expo Center Karachi, and you are hired to design the logic circuit for the newly installed lift. The lift only stops at Ground, Second, Third Floors. The lift has one button (RUN), that can be turned into Up or Down position. When the switch is turned to the UP position (i.e. R=1), the lift goes upward from the Ground floor (i.e. 0) to the top floor (i.e. 3), and if the switch is turned to the DOWN position (i.e. R=0) it will go downward. Design this synchronous sequential circuit for this up-down counter using the JK-flip- flops. Perform all design steps, including state-diagram, state-table, K-map, minimized expressions and finally, the draw the logic circuit.
Compare the circuits, characteristic tables, and the timing diagrams of SR Flip-flops, JK flip-flops, and D flip flops. In your own words, describe the similarity and differences in behavior of these flip flops. Then go on to make comparison between Mealy and Moore machines, first describe each FSM and then elaborate on the similarity and differences between them.
Q5 A Moore machine is to detect three or more consecutive zeros on an input bitstream using D flip flops. (a) Present the truth table and state diagram. (b) Interpret the simplified logic expression using K-Map. (c) Sketch the circuit with appropriate labeling.
S Display will be designed for a thermometer. The display will show that degree for minimum temperature and 99 degrees for maximum temperature. According to this; a) What is the number of bits that will be needed in the binary code to express the temperature? b) What are the binary, octal and hexadecimal equivalents of 95 degrees? () What is the BCD representation of 95 degrees? d) What is the hex equivalent of this temperature when it shows 111 degrees octal? e) If the thermometer showed a temperature between -99 and +99 degrees, how many bits would we need?
Design a 5 asynchronous counter counting from 7 to 2. (JK or T type flip-flopsuse)