28. Find the transfer function, G(s) = X1(s)/F(s), for thetranslational mechanical system shown in Figure P2.13.[Section: 2.5]2 N-s/mX3(1)2 N-s/m(1)'x-[4 kg2 N-s/m6 N/m6 N/m4 kg0000 4 kg"FrictionlessFIGURE P2.13USE MATRIX METHOD

Answered: Image /qna-images/answer/bb57d3c8-e11a-498e-a578-e6ce77d4122d.jpg

28. Find the transfer function, G(s) = X1(s)/ F(s), for the translational mechanical system shown in Figure P2.13. [Section: 2.5] 2 N-s/m I3(1) 2 N-s/m 6 N/m 6 N/m 2 N-s/m 4 kgH H Frictionless FIGURE P2.13

28. Find the transfer function, G(s) = X1(s)/ F(s), for the translational mechanical system shown in Figure P2.13. [Section: 2.5] 2 N-s/m I3(1) 2 N-s/m 6 N/m 6 N/m 2 N-s/m 4 kgH H Frictionless FIGURE P2.13

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A liquid storage system is shown below. The normal oper-ating conditions are q1=10 ft3∕min,q2=5ft3∕min,h=4ft.The tank is 6 ft in diameter, and the density of each stream is 60 lb/ft3. Suppose that a pulse change in q1 occurs as shown inFig.(a)What is the transfer function relating H′ to Q′1?(b)Derive an expression for h(t) for this input change.(c)What is the new steady-state value of liquid level h?(d)Repeat (b) and (c) for a change in q1 from 10 to 20 (at t=0) to 15 ft3/min at t=12
Represent the translational mechanical system shown in state space, where x3(t) is the output.
Find the transfer function,G(s)=Z1(s)/H(s) Find the state space model.
How can a transfer function be derived from a system model, and what information does it provide about the system's behavior?
Transfer function on translational mechanical system
Find: State-space representation Note: Output of mechanical system is X3(t) Given: M1=1 kg, M2=1 kg, M3=1 kg K1=1 N/m, K2=1 N/m Fv1=1 N-s/m, Fv2=1 N-s/m, Fv3=1 N-s/m, Fv4=1 N-s/m
Take the mass of the block is M(kilogram=Newton-second2/meter), the spring constant is K(Newton/meter), the coefficient of viscous friction is fv(Newton-second/meter), distance takenin time is x(t)(meter) and force used in the system is f(t)(Newton). Write the transfer functionsfor figure 1.1, and figure 1.2.Solve only this--> Accept that the M=2 kg, K=1 N/m, fv=1 N-s/m and find the transfer function according to thosevalues.
1) Obtain a state space model of the system. 2) Given m =1 kg, k = 1 N/m and b = 1 N.s/m is the system Controllable? 3) For what values of k,m,b the system is stable? Explain your answer?
Sketch the level response for a bathtub with cross-sectional area of 8 ft 2 as a function of time for the following sequence of events; assume an initial level of 0.5 ft with the drain open. The inflow and outflow are initially equal to2ft3/min.(a)The drain is suddenly closed, and the inflow remains con-stant for 3 min (0≤t≤3).(b)The drain is opened for 15 min; assume a time constant in a linear transfer function of 3 min, so a steady state is essentially reached (3≤t≤18) (c)The inflow rate is doubled for 6 min (18≤t≤24).(d)The inflow rate is returned to its original value for 16 min(24≤t≤40).
Take the mass of the block is M(kilogram=Newton-second2/meter), the spring constant is K(Newton/meter), the coefficient of viscous friction is fv(Newton-second/meter), distance takenin time is x(t)(meter) and force used in the system is f(t)(Newton). Write the transfer functionsfor figure 1.1, and figure 1.2
A velocity of a vehicle is required to be controlled and maintained constant even if there are disturbances because of wind, or road surface variations. The forces that are applied on the vehicle are the engine force (u), damping/resistive force (b*v) that opposing the motion, and inertial force (m*a). A simplified model is shown in the free body diagram below. From the free body diagram, the ordinary differential equation of the vehicle is: m * dv(t)/ dt + bv(t) = u (t) Where: v (m/s) is the velocity of the vehicle, b [Ns/m] is the damping coefficient, m [kg] is the vehicle mass, u [N] is the engine force. Question: Assume that the vehicle initially starts from zero velocity and zero acceleration. Then, (Note that the velocity (v) is the output and the force (w) is the input to the system): 1. What is the order of this system?
A velocity of a vehicle is required to be controlled and maintained constant even if there are disturbances because of wind, or road surface variations. The forces that are applied on the vehicle are the engine force (u), damping/resistive force (b*v) that opposing the motion, and inertial force (m*a). A simplified model is shown in the free body diagram below. From the free body diagram, the ordinary differential equation of the vehicle is: m * dv(t)/ dt + bv(t) = u (t) Where: v (m/s) is the velocity of the vehicle, b [Ns/m] is the damping coefficient, m [kg] is the vehicle mass, u [N] is the engine force. Question: Assume that the vehicle initially starts from zero velocity and zero acceleration. Then, (Note that the velocity (v) is the output and the force (w) is the input to the system): A. Use Laplace transform of the differential equation to determine the transfer function of the system.