Q3: A' am with cross section shown in the following image, find out the principle аxes. 100mm L. 600mm 100mm 400mm

Q: HW *5 A horizontal bar, 1o Pt long and of negligible Weight, rests on the inclined planes as shown…

A:

Q: 3. Given a fourbar slider-crank linkage with the link lengths L2 = a = 40 mm, L3 = b = 120 mm,…

A: solving the part 1 we have

Q: A 1.5-m long, copper rod is removed Irom a treatment oven at 550°C and immersed ina airstream…

A: Given                     Velocity, V = 2.5 m/s Thermal conductivity, k = 0.02735 W/mK…

Q: A tree feller cuts off large tree near the ground level and then continues to hoist the trunk. If…

A: mass=3tonne=3metric tonConsidering that the distances are in mmVertical Distance =180+1080=1.26m…

Q: The complete specification of the action of a force must include: The magnitude and direction of the…

A:

Q: Vector quantities are: The same as scalars. Characterized by magnitude and direction and they…

A: Vector quantities are characterized by magnitude and direction and they combine by the parallelogram…

Q: 1.) For the curved surface AB: a.) Determine the magnitude, direction, and line of action of the…

A:

Q: 1) The state of an element is shown in figure Fig. - 1. Use Mohr's circle to find the stresses and…

A:

Q: 4. Compuk deter mi nant of A: the 4. -1 2. A = 10 3 4.

A:

Q: Consider a steam power plant operating on the ideal Rankine cycle. Steam enters the turbine at 3 MPa…

A: Solution: The T-S diagram for the given problem can be drawn as: At, pressure at point 1 P1 = 3 MPa…

Q: Glycerin at 20 °C flows upward in a vertical 75-mm-diameter pipe with a centerline velocity of 1.0…

A:

Q: 1. Calculate the density of a high-leaded brass with a composition of 64.5 wt% Cu, 33.5 wt% Zn, and…

A:

Q: A Methanol pool fire shows a fuel mass loss rate of 0.01 kg/s on a load cell Estimate the heat…

A: Disclaimer Since you have asked multiple question, we will solve the first question for you. If you…

Q: A 12 m long steel pipe has an internal diameter of 80 mm and a wall thickness of 2.5 mm. Calculate…

A:

Q: Determine the smallest metric hydraulic copper tube size that will carry 4L/min of the following…

A: Solution to part (d) as mentioned by the student:

Q: 2. Express the internal shear and moment in terms of x and then draw the shear and moment diagrams.…

A:

Q: 2. Steam enters a reheat-regenerative turbine at 6 MPa and 400 °C. After partial expansion to 1.2…

A:

Q: Find the value of strain if stress is 4 N/mm2 and elasticity is 10000 N/mm2

A:

Q: QUESTION 2 Condenser Diagram 2E shows an ideal cascade vapour-compression refrigeration cycle using…

A: Given: m1˙=11160 kg/hour=3.1 kg/sP1=100 kPaP2=P3=280 kPaP6=P7=900 kPa To find 1. Coefficient of…

Q: At the instant shown, the shaft and plate rotate with an angular velocity of 14 rad/s and angular…

A:

Q: A large artery in a person's body can be approximated by a tube of diameter 9 mm and length 0.35 m.…

A:

Q: The velocity gradient is 1000 / s. The viscosity is 1.2 X 10 -ª N s/m². The shear stress (N/m) *

A: Unit of shear stress is N/m2 and not N/m.

Q: 1.A boiler consumes 16,800 pounds of fuel/hour when producing 210,000 pounds steam/hour at 620 psia…

A:

Q: The sphere of diameter of 5.0 cm is moving in still water at a velocity of 2.0 m/s. The drag…

A:

Q: A truck weighing 17000 N is resting on a ramp that is inclined at an angle of 15° to the horizontal.…

A:

Q: A 1.5-m long, copper rod is removed Irom a heat- treatment oven at 550°C and immersed in a 55°C…

A: Given dataLength of copper rod = 1.5 mTemperature of surface of copper rod = Ts  = 550°CTemperature…

Q: A steel railroad track (E=200GPa, α=11.7x10^-6/°C) was laid out at a temperature of -6°C. Determine…

A: Given   Temperature, T1 =-6°C                        T2 = 48°C                         α…

Q: In reading dial indicators, the sensitivity of the long needle is meter.

A: Sensitivity defines the smallest value for that the instrument will be sensitive.

Q: A large artery in a person's body can be approximated by a tube of diameter 9 mm and length 0.35 m.…

A: Given   Initial pressure, P1 = 120 mm of Hg                                 = 15.96 kN/m2…

Q: The velocity potential function, o, is given by o = x - y. Find the velocity components in x and y…

A:

Q: Find the coefficient of friction if friction force is 723N Normal force is 823 N

A: Given: F = 723 N N = 823 N

Q: Front, top and side view

A:

Q: Solder which contains 95% Tin, 4% Copper, and 0.5% Silver has a melting point at 219 °C. The creep…

A: silver melting point =219°cTm=219+273=492 kfor creep T=0.04TmT⩾0.4×492⩾196.8 kT⩾-76.2°c

Q: A former student of mechanics wishes to weigh himself but has access only to a scale A with capacity…

A: Find the correct weight of man.

Q: more than one item per item The engine cycle that does not require an outside source of ignition.…

A: The engine cycle that does not require an outside source of ignition. Ans: Brayton cycle  In Brayton…

Q: In a circular path, the center of the radius-of-curvature is fixed. false none of these true…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: a) Briefly explain the characteristics of a laminar flow.

A:

Q: Water is heated while following through a 1.5cmx 3.5cm rectangular cross section tube at a velocity…

A:

Q: Take note that if the figure CDFE is traced, it becomes a parallelogram. Additionally, members BCD…

A: Given Data The compressive force of AB is:FAB=-37 kN To find: The load L in kN. The force in link…

Q: Q8) A wire of a perfectly plastic material has a starting diameter of 3 mm. Assume no friction and…

A:

Q: Compute the horsepower output of the following described engine operating at 2000 rpm, bore 3.5 in.,…

A:

Q: There can be more than 1 answer per item What is the purpose of having piston ring gaps? So that…

A:

Q: Water at 20 °C flows through a horizontal 1-mm-diameter tube to which are attached two pressure taps…

A:

Q: - If possible, please include analysis and/or procedure - The candlestick shown in the figure has a…

A:

Q: 4. The figure below shows a bulldozer. Notice that the track on the bulldozer (the tread that wraps…

A: We can answer up to 3 subparts so we will answer first 3. Please resubmit the question by specifying…

Q: A long cable of length L = 41 m and mass p = 0.173 kg/m is wrapped around the periphery of a spool…

A:

Q: Glycerin at 20 °C flows upward in a vertical 75-mm-diameter pipe with a centerline velocity of 1.0…

A: Find the head loss and pressure drop.

Q: | 13. Oil of SG = 0.87 and a kinematic viscosity v = 2.2 x 10-4 m2/s flows through the vertical pipe…

A:

Q: The sun generates an average of 1.958 kW/m2 when tapped as source of energy wherein a flat-plate…

A: Given that: Average power = 1.958 kW/m2 Flat plate collector area = 1.006 m2 Water flow rate = 50.1…

Q: Express F as a vector in terms of the unit vectors i, j, and k. Determine the angle between F and…

A:

Buckling of columns

The column is described as a vertical member of the structure that carries an axial compressive load, and buckling is a lateral deformation of the column under the application of load.