3-49 The pressure difference between an oil pipe and water pipe is measured by a double-fluid manometer, as shown in Fig. P3-49. For the given fluid heights and specific gravities, calculate the pressure difference AP PR - PA 1

3-49 The pressure difference between an oil pipe and water pipe is measured by a double-fluid manometer, as shown in Fig. P3-49. For the given fluid heights and specific gravities, calculate the pressure difference AP PR - PA 1

Name: แสดงวิธีทำให้ดูหน่อย 3-49 The pressure difference between an oil pipe
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: แสดงวิธีทำให้ดูหน่อย 3-49 The pressure difference between an oil pipe and waterpipe is measured by a double-fluid manometer, as shown inFig. P3-49. For the given fluid heights and specific gravities,calculate the pressure difference AP = PR - PAAWate

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.122P: The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate...

See similar textbooks

Similar questions

the gauge pressure of the air in the tank is shown in Fig. p3-49 is measured to be 65 kPa. Determine the differential height H of the mercury column.
Need quick handwritten solution. The gauge pressure in the air container in Fig. P1-83 is 80kPa . Calculate the differential height h of the column of mercury.
Find the difference in pressure between tanks A and B in kPa shown in Fig. 2-64 if d1, d2, d3, and d4 are equal to 320 mm,150 mm,494 mm, and 166 mm, respectively.
Determine the reading h in meter based on Fig. 2-22 for a pressure of 52 kPa vacuum at point A if the liquid is kerosene (s.g.=0.83).
Plz answer I will rate !:) A right circular cylindrical tank with its circular base on the ground is full of water. The diameter of the base is 4m and the height of the tank is 4m. Set up a Riemann sum to approximate the hydro static force against the lateral wall of the tank. Then express the force as an integral and evaluate it.
Please don't copy,Solve in handwritten format only. The gauge pressure in the air container in Fig. P1-83 is 80kPa . Calculate the differential height h of the column of mercury.
Find surface tension in a soap bubble of 45 mm diameter when the inside pressure is 2.812 N/m2 above atmosphere. (ENTER ONLY THE VALUES IN THE BOXES BY REFERRING THE UNIT GIVEN IN BRACKETS) The surface tension of the soap bubble (unit is N/m) = _____________ Short Answer
Open tank (4.5 m long, 2.5 m height and 3 m wide) contains liquid (S-0.75) to height 1. m. If this tank is accelerated along its length on a horizontal truck at a constant value of 3.5 m/s, determine pressure at the bottom of the tank at front and rear edges (in kN/m). (take y=9.8 kN/m for water)
For a vertical rectangular gate, one side has linseed oil (0.938) and the other has two fluids—castor oil (0.96) and water. Considering a unit-width of the gate, apply the PRESSURE PRISM CONCEPT (Illustrate and label the pressure diagram/prism) to calculate the magnitude and direction of the following when z = 7m. FIND: A. The hydrostatic force due to linseed oil F1. B. The hydrostatic force due to castor oil F2. C. The hydrostatic force due to water. D. The net hydrostatic force acting on the gate Fnet
In a fluid 1 is oil (sg=0.87) and fluid 2is glycerine at 20 degrees Celsius (w=12360N/m cubed) if Patm=98kpa determine the absolute pressure at p1 Here is the diagram in the picture below
An open manometer, shown in the figure, is installed to measure the pressure in a pipe carrying an oil (SG = 0.82). If the manometer liquid is carbon tetrachloride (SG = 1.60) determine the pressure in the pipe (in N/m2). Find the pressure head in meters of water column height.
For a vertical rectangular gate, one side has linseed oil (0.938) and the other has two fluids—castor oil (0.96) and water. Considering a unit-width of the gate, apply the PRESSURE PRISM CONCEPT (Illustrate and label the pressure diagram/prism) to calculate the magnitude and direction of the following when z=20ft.