(3) The 12-lb lever OA with 10-in. radius of gyration about point O is initially at rest in the vertical position (8 = 90°), where the attached spring of stiffness k= 3 lb/in is unstretched. Calculate the constant moment M applied to the lever at O which will give the lever an angular velocity o = 4 rad/sec as the lever rotates to the horizontal position at 0 = 0. k = 3 lb/in. wwww 15 15

(3) The 12-lb lever OA with 10-in. radius of gyration about point O is initially at rest in the vertical position (8 = 90°), where the attached spring of stiffness k= 3 lb/in is unstretched. Calculate the constant moment M applied to the lever at O which will give the lever an angular velocity o = 4 rad/sec as the lever rotates to the horizontal position at 0 = 0. k = 3 lb/in. wwww 15 15

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The velocity of the 8-kg cylinder is 0.3 m∕s at a certain instant. The speed v after dropping an additional 1.5 m is 2.5 m/s. The mass of the grooved drum is 12 kg, its centroidal radius of gyration is k = 210 mm, and the radius of its groove is ri = 200 mm. The frictional moment at O is a constant 3 N∙m. Find the frictional force.
A homogeneous 150-kg vertical bar AB is raised from rest at θ = 0° by means of the parallel swinging bars of negligible weight, with a constant moment M = 5 kN-m applied to the lower link at C. Determine the angular velocity and the angular acceleration of the links and the forces at A and B at the instantθ = X°. Take the angle θ = 37°.
In the figure, the slender bar (1), with a mass of 30 kg, is attached to the sphere (2), with a mass of 80 kg. Given the angular velocity shown at the provided angle, determine: a. The angular acceleration of the combined body b. The reactions in the pin at point O
1) Three small spheres are rigidly mounted to a horizontal shaft with rotates with angularvelocity omega as shown. Neglect sphere radii, ignore gravity. Spheres have masses m1, m2andm3 as shown.a. What is the angular momentum HO about O the center of the coordinates shown?b. At this instant, what is Ax , the x component of the bearing force at A to offset the dynamicimbalance? Note that you are NOT asked to find any other forces (Ay, Ox, or Oy) in interestof time.
1)Calculate the velocity of the arm, observed by a stationary person on the ground.2)Draw the FBD of the combined body (crane body, arm and load).3)Is the combined body stable? Why?4)Calculate the moment of the following, about wheel A,i) combined crane bodyii) load mass5)Which combined body’s component(s) will not fail? Why? (Hint: The crane was initially in equilibrium.)6)What are the various limits (maximum or minimum) for the combined body to be stable? Explain why.
A torque T = 0.30 N-m is applied to a bevel gear B. Bevel gear D meshes with gear B and drives pump A. Gear B has a radius of gyration of 150 mm and a weight of 50 N, whereas gear D and the im- peller of pump A have a combined radius of gy- ration of 50 mm and a weight of 100 N. Find how many revolutions of gear B are needed to get the pump up to 200 rpm from rest. What is the power output of the pump at this speed if it is 90% efficient.
The bar AB is uniform and has a mass of 50.0 kg. At the moment shown, the rod has an angular velocity of 4.00 rad/s and spring is stretched by 0.30 m. The force constant of the spring is 25.0 N/m.a) Determine whether or not the bar will reach the horizontal position.b) If the bar becomes horizontal, calculate its angular velocity at that position. If not, calculate the angle the bar makes with the horizontal when it comes to rest momentarily.
The small end rollers of the 8-lb uniform slender bar (length = 4 ft) are constrained to move in the slots, which lie in the vertical plane. At the instant when Angle theta = 30°, the velocity of roller A is 13 ft/s down the vertical slot. Determine the angular acceleration of the bar, the acceleration of mass center G and the reactions of points A and B, under the action ofthe 6-lb force P. Neglect the friction and the mass of the small rollers.
The double pulley shown in the figure is formed by two wheels that are coupled to each other. The complete pulley (formed by the two wheels) has a mass of 15 kg and a turning radius of 110mm. Block A has a mass of 40 kg. If a force of 2 kN is applied to the tied rope of the inner pulley wheel, determine the speed of block A after 3 seconds. At the beginning, the whole system was at rest. Disregard the mass of the string and consider that the moment of inertia (kg.m²) of the complete pulley is given by IP = mko²where m is the mass of the pulley and Ko is the radiusspinning
The mass of the A gear is 10 kg and the turning radius is 200 mm. Of gear Bits mass is 3kg and the turning radius is 80 mm. When the system is stationary to gear B. Moment of 6 N.m is applied. By neglecting friction;Find the tangential force from gear B to gear A.
The uniform 2-kg slender bar AB is mounted on a vertical shaft at C.A constant couple of 9 N-m is applied to the bar. Calculate the angular acceleration of the bar and the magnitude of the horizontal reaction at C at the instant when the angular velocity of the bar is 6 rad/s.
The uniform 140-lblb beam is initially at rest when the forces are applied to the cables. Set FAFAF_A = 70 lblb and FBFBF_B = 190 lblb .(Figure 1) Determine the magnitude of the acceleration of the mass center at this instant. Determine the angular acceleration of the beam at this instant.