A thin rod AD is mounted with bearings on either side to allow the system to spin. Two small rods are welded onto AB, each of length 107 mm and mass 320 g. A couple 6 N-m is applied to the rod. Determine the reaction at the mounting point D when the angular velocity is 1100 rpm. To simplify the problem, let's assume the moment of inertia from the rod AD can be neglected. C 107mm A 160mm 160mm 107mm D B M 320mm Dy - Dz The units of the reaction are

A thin rod AD is mounted with bearings on either side to allow the system to spin. Two small rods are welded onto AB, each of length 107 mm and mass 320 g. A couple 6 N-m is applied to the rod. Determine the reaction at the mounting point D when the angular velocity is 1100 rpm. To simplify the problem, let's assume the moment of inertia from the rod AD can be neglected. C 107mm A 160mm 160mm 107mm D B M 320mm Dy - Dz The units of the reaction are

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Bar BC weighs 161 lb and has a radius of gyration of mass with respect to a hor- izontal axis through G of 3.0 ft. The bar is supported by the cords AB and CD which rotate in the same vertical plane. The speed of the mass centre, when in the position shown, is 12 fps. Determine the tension in cables AB and CD for this position.
3.32). As shown in Figure 3, a yo-yo toy is formed by wrapping a massless cord around adisk of radius R= 0.2 m and mass M=3 kg. The cord is vertical and its top end is fixed and the disk isinitially stationary. The cord remains vertical for the entire motion and does not slide on the disk.When the disk is released from rest, it falls down by a distance H=0.8 m, The moment of inertia ofthe disk around its center is I disk=1/2mdiskR^2a . Find the angular acceleration of the disk when it is lowered by a distance H.b . Find the angular velocity of the disk when it is lowered by a distance H.
An aeroplane makes a complete half circle of 50 metres radius, towards left, when flying at 200 km per hour. The rotary engine and the propeller of the plane has a mass of 400 kg with a radius of gyration of 300 mm. The engine runs at 2400 r.p.m. clockwise, when viewed from the rear. Find the gyroscopic couple on the aircraft and state its effect on it. What will be the effect, if the aeroplane turns to its right instead of to the left ?
A small grinding wheel is attached to the shaft of an electric motor that has a rated speed of 3600 rpm. When the power is turned off, the unit coasts to rest in 70 s. The grinding wheel and rotor have a combined weight of 6 lb and a combined radius of gyration of 2 in. Determine the average magnitude of the couple due to kinetic friction in the bearings of the motor.
A rigid body is made of three identical thin rods, each of mass m and length L= 0.6 m,attached together in the form of an H. The body is allowed to fall from the horizontalposition, rotating around one of the legs of the H.a) What is the rotational inertia of the H, in terms of m and L?b) What will be the angular speed of the H when it is oriented vertically?
A homogeneous 150-kg vertical bar AB israised from rest at ? = 0° by means of theparallel swinging bars of negligible weight,with a constant moment ? = 5 kN-m appliedto the lower link at C. Determine the angularvelocity and the angular acceleration of thelinks and the forces at A and B at the instant? = 34°. (I have seen a solution on this sight but there seems to be an error in the integration step, please clarify integration)
Problem 158. The 20 kg wheel has an eccentric mass which places the center of mass G a distance r ̅=70 mm away from the geometric center O. A constant couple M=6 N·m is applied to the initially stationary wheel, which rolls without slipping along the horizontal surface and enters the curve of radius R =600 mm. Determine the normal force under the wheel just before it exits the curve at C. The wheel has a rolling radius r=100 mm and a radius of gyration k_o=65 mm.
In the helicopter shown; a vertical tail propeller is used to pre- vent rotation of the cab as the speed of the main blades is changed. Assuming that the tail propeller is not operating determine the final angular velocity of the cab after the speed of the main blades has been changed from I80 to 240 rpm. (The speed of the main blades is measured relative to the cab, and the cab has a centroidal moment of inertia of 650 lb.ft.s2. Each of the four main blades is assumed to be a slender rod 14 ft weighing 55 lb.)
A uniform disc of diameter 315mm and of mass 14 kg is mounted on one end of an arm of length 600 mm.Then the couple will _________________N-m
A baseball attachment that helps people with mobility impairments play T-ball and baseball is powered by a spring that is unstretched at position 2. The spring is attached to a cord that is fastened to point B on the 75-mm radius pulley. The pulley is fixed at point O , rotates backwards to the cocked position at 0 , and the rope wraps around the pulley and stretches the spring with a stiffness of k = 2000 N/m. The combined mass moment of inertia of all the rotating components about point O is 0.40 kg·m2. The swing is timed perfectly to strike a 145-gram baseball travelling with a speed of V0 = 10 m/s at a distance of h = 0.7 m away from point O. Knowing that the coefficient of restitution between the bat and ball is 0.59, determine the velocity of the baseball immediately after the impact. Assume that the ball is travelling primarily in the horizontal plane and that its spin is negligible.
A 3 kg disk shown is pin supported at its center. The disk is rotated from rest and attains a constant angular velocity of 15 rad/s. If the mass of the rope is negligible and the radius of gyration of the drum is 50 mm; Find out the angular acceleration of the drum, the tension in the rope, and the torque experienced by the drum.
A cylinder shown has a weight of 100lb Assuming the cylinder to be solid indetermining the moment of inertiaa.Determine the velocity of the cylinder after it has rolled 10ft from restif the horizontal force P applied at A is 10lbb.Determine the velocity of the cylinder after it has rolled 10 ft fromrest if the horizontal force P=10lb is applied at Bc.Determine the velocity of the cylinder after it has rolled 10 ft fromrest if the horizontal force P=10lb is applied at C