3. A 4.0 L six-cylinder engine is operating at 3000 rpm. The engine has a compression ratio of 10:1, and volumetric efficiency of 0.85. If the bore and stroke are equal, what is the stroke, the mean piston speed, cylinder clearance volume, and air mass flow rate into the engine? Assume standard inlet conditions (Patm=101kPa and T=25°C)

3. A 4.0 L six-cylinder engine is operating at 3000 rpm. The engine has a compression ratio of 10:1, and volumetric efficiency of 0.85. If the bore and stroke are equal, what is the stroke, the mean piston speed, cylinder clearance volume, and air mass flow rate into the engine? Assume standard inlet conditions (Patm=101kPa and T=25°C)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A four-cylinder engine has a 85 mm bore ? and 90 mm stroke ?, and operates at 5000 rpm.What is the power lost to piston skirt friction?
1. An 11.1 liter, 6 cylinder, 4 stroke engine has a 120 mm bore and 125 mm stroke. If its compressions ratio is 16, what is the clearance volume? What is the engine displacement per minute if it runs at 2,000 rpm? If biogas, with an energy content of 4,500 Kcal/m3 will be fueled into the engine, what would be its power output (in KW) considering a 10% brake thermal efficiency?
Air Is To Be Compressed In A Single-Stage Reciprocating Compressor From 1.013 bar And 15°C To 7 bar.For A Free Air Delivery Of 0.3 meter cubed per min.The Compressor Is To Run At 1000 rev/min.If The Compressor Is Single-Acting And Has A Stroke/Bore Ratio Of 1.2/1, Calculate The Bore Size Required.
If an engine has a bore of 0.1 m, stroke of 0.08 m, inlet flow effective area of 4.0 × 10−4 m2, and inlet temperature of 320 K, what is the maximum speed it is intended to be operated while maintaining good volumetric efficiency?
A 3-liter 6-cylinders square engine (bore = stroke) with two intake valves and one exhaust valve per cylinder is designed to have an output power of 300 kW and a corresponding bmep of 18.5 bar. The intake temperature is 55°C. Assume an average flow coefficient at the intake valve of 0.35. a) Calculate the intake valve area and the diameter of intake valves for a good volumetric efficiency (Mach index Z of 0.6) b) Calculate the exhaust valve area if the exhaust gases temperature is 600°C; the average flow c) The exhaust valve opens when the piston is at the bottom dead center. For a lift 1 = 1.35 cm of the coefficient at the exhaust valve is 0.6. exhaust valve, calculate the flow rate through the exhaust valve. The average flow coefficient at the exhaust valve is 0.6 and the cylinder pressure and temperature are 500 kPa and 600°C. Assume exhaust system pressure is 105 kPa. Notes: The specific heat ratio and gas constant for the gases at the inlet and exhaust valves are respectively…
A 3-liter 6-cylinders square engine (bore = stroke) with two intake valves and one exhaust valve per cylinder is designed to have an output power of 300 kW and a corresponding bmep of 18.5 bar. The intake temperature is 55°C. Assume an average flow coefficient at the intake valve of 0.35. a) Calculate the intake valve area and the diameter of intake valves for a good volumetric efficiency (Mach index Z of 0.6) b) Calculate the exhaust valve area if the exhaust gases temperature is 600°C, the average flow coefficient at the exhaust valve is 0.6. c) The exhaust valve opens when the piston is at the bottom dead center. For a lift I = 1.35 cm of the exhaust valve, calculate the flow rate through the exhaust valve. The average flow coefficient at the exhaust valve is 0.6 and the cylinder pressure and temperature are 500 kPa and 600°C. Assume exhaust system pressure is 105 kPa. Notes: The specific heat ratio and gas constant for the gases at the inlet and exhaust valves are respectively 1 =…
A 6.4-liter, V8 Spark ignition (8 cylinder) 4-stroke engine operates at an engine speed of 3200 RPM. The compression ratio is CR = 10.5:1. At this speed volumetric efficiency is 93%, combustion efficiency is 98%, indicated thermal efficiency is 47%, and mechanical efficiency is 86%. Stroke and bore will be related by S = 0.90 B. Combustion starts at 18 degrees bTDC and last for 0.25 seconds. Calculate? a.Overall efficiencyb. Piston displacementc. Cylinder bore and stroked. average piston speed and max piston speede.distance piston has traveled from TDC at the end of combustion, f. volume at the end of combustion g. position of crank at the end of combustion
An ideal six cylinders diesel engine has a compression ratio of 17 and a cutoff ratio of 2.3. Find the power produced by this engine if the temperature and pressure at the beginning of the compression stroke are 250C and 98kPa respectively. Please give detailed solution and step by step Thank you
3. A rear mounted air-cooled SI engine has 6 cylinders, 3.375 in x 2.6 in bore and stroke respectively, acompression ratio of 8 and developed 80 BHP at 4400 rpm. It was noted that brake thermal efficiency is26 %, volumetric efficiency is 74 % and mechanical efficiency is 71 %. For the ideal cycle, conditions atthe start of compression are 14.7 psia, 140 o F.Calculate a) Percent clearance, b) P, T at the end of compression, c) Brake engine efficiency, d) massflow rate of air, e) torque (lb-ft), f) AF with Q hv = 19100 BTU/lb fuel
A certain six-cylinder engine has a 130.2 mm bore, a 127 mm stroke, and a clearance volume of 0.119 L in each cylinder. Does the engine run on diesel or gasoline fuel? Explain your answer
a. Assume a blower operating at 4000 rpm compressing air from 68 degree Fahrenheit and 14.7psia to 8.5psig, handling 16000 cfm at the design point with an efficiency of 70%. It is desired to find the operating conditions (BHP, H and Q) at 3600 rpm.b. Same as problem (a) except assume that the speed and inlet temperature remains the same, but the inlet pressure at the point considered, drops to 10psia.c. Same as problem (a) except assume that the speed and inlet pressure remains the same, but the inlet temperature rises to 100 degree Fahrenheit.
For example, the intake valve of the 4-stroke 6-cylinder revision KA engine with a volume of 2.4 was opened at 12 emme KMA and closed at 56˚ KMA early at high revs. How much KMA is required for the 4500 running engine H/Y 14? What would be the actual compression ratio? Calculate. The compression ratio is 9, the crank spring ratio of the Connecting Rod is R3, the applied and general constant during the whole suction is 288 K and 96. The amount of fuel you spray 1 KMA of the injector is 0.210-5 kg. Gas constant of air Rh=0.287 kJ/kg K.