For the simply supported beam subjected to the loading shown, derive equations for the shear force Vand the bending moment Mfor any location in the beam. (Place the origin at point A.) Let a=2.75 m, b=5.00 m, PB = 60KN, and Pc = 80kN. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GOexercise.Answers:Ay =Dy=teltelaiBaCalculate the reaction forces Ay and Dy acting on the beam. Positive values for the reactions are indicated by the directions of thered arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.)PBBaPBPcaCPcCKNbKNDbDXD₂X

Answered: Image /qna-images/answer/d4663cb5-0c59-4870-99a6-60fdcd84e2e0.jpg

Calculate the reaction forces Ay and Dy acting on the beam. Positive values for the reactions are indicated by the directions of t red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.)

Calculate the reaction forces Ay and Dy acting on the beam. Positive values for the reactions are indicated by the directions of t red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.)

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.42P: For the beam AB shown in Cases 1 and 2, derive and plot expressions for the shear force and bending...

See similar textbooks

Related questions

Q: P 3.5 A O 179 kips 140 kips 85 kips O 112 kips O 151 kips B M 6.5 ft

Q: Answers: P= i T₂ = i KN KN

Q: For the two element rod shown, element (1) is steel with: E₁ = 210 GPa, A₁ = 1000 mm², L₁= 2 m, and…

Q: The horizontal force P = 85 N is applied to the upper block with the system initially stationary.…

A: F.B.D. of the given system:

Q: 4 m A 5 m B VB = 2m/s aB = 4 m/s²

Q: A pair of meshing gears has a diametral pitch of 10.7140, a center distance of 2.8-in, and a…

Q: b) Pfluid Wood h d, wood = Fluid Plastic h d, plastic Figure Q2b A cylinder wood block (SG wood 0.4)…

Q: STATICS OF RIGID BODIES RATE WILL BE GIVEN! NO LONG EXPLANATION NEEDED! SHOW THE COMPLETE SOLUTIONS.…

Q: The Figure shown below is a parallel pipeline system with two branches used to supply lubricating…

Q: The slender 9-kg bar AB is horizontal and at rest, and the spring is unstretched. Determine the…

A: Draw the diagram of the above system.

Q: (a) Determine the reactions at A and E if P = 1030 N. The reactions are positive if to the right or…

Q: B) The Figure shows Mohr's circle for a point in a physical object that is subjected to plane…

Q: Explain how the relationship between temperature and the tensile strength of polymers ?"

A: We have to explain relationship between temperature and the tensile strength of polymers

Q: A flanged wooden shape is used to support the loads shown on the beam. The dimensions of the shape…

Q: The truss is composed of equilateral triangles of side a = 2.4 m. The load is L = 370 N. Determine…

A: Given data: Side length of triangle (a) = 2.4 m Magnitude of the load (L) = 370 N Concept: At…

Q: Determine the forces in members BE and CE of the loaded truss. The forces are positive if in…

Q: Use the graphical method to construct the bending-moment diagram and identify the magnitude of the…

Q: The Figure shown below is a parallel pipeline system with two branches used to supply lubricating…

Q: If the cord at B suddenly fails, determine a) The angular acceleration of the beam. b) The…

Q: The softball is originally traveling to the left. Then, it is struck by the bat, and travels to the…

A: In physics, the term "impulse" is used to characterise or measure the impact of force operating…

Q: The signboard truss is designed to support a horizontal wind load of 680 lb. If the resultant of…

Q: Required information An air-standard Diesel cycle has a compression ratio of 18.2. Air is at 120°F…

Q: Compound axial member ABC has a uniform diameter of d - 2.4 in. Segment (1) is an aluminum [E₁ -…

A: In the given problem, I can answer only part (1) because part (2), (3) are not visible so please…

Q: An air-standard Diesel cycle has a compression ratio of 18.2. Air is at 120°F and 14.7 psia at the…

Q: H 2.2 2,1 A Өк 40° х

Q: Consider a steam turbine power plant as shown with the given properties below. Enter state of pump…

Q: The cross section of a bearing block is shown in the figure by the shaded area. Calculate the moment…

Q: 5.) Air is kept at a pressure of 135 MPa absolute and a temperature of 15 C in a 7000 ml container.…

Q: The signboard truss is designed to support a horizontal wind load of 720 lb. If the resultant of…

Q: Determine the force in each member of the loaded truss. Discuss the effects of varying the angle of…

Q: Use method of section, determine the force in member BE of the loaded truss.

Q: 78 A steam power plant operates on regenerative steam cycle as shown in figure. 1 kg Pump (8) 1 kg…

A: Given data, h2= 2679 KJ/kg, h3 = 2365KJ/kg, hf5= 137.8 KJ/kg, hf6=467.1 KJ/kg, hf7=762.6 KJ/kg. For…

Q: Cable AB passes over the small ideal pulley C without a change in its tension. What length of cable…

Q: The air in an ideal Otto engine is initially at 14.5 psia, 100 deg F. At the end of isentropic…

A: Given: The air temperature at inlet, T1 = 100 F = 559.67 R The air pressure at inlet, P1 = 14.5 Psia…

Q: Find the natural frequencies of the system using eigenvalues.

A: Eigenvalues are calculated only for the square matrix. Therefore, the required square matrix from…

Q: P₂ * 1/3 + 2,5-1,8 = 2/3 +² ₂ === Y OB.h₂ = (2₂-2₂) +h, OCP₁ 7 -2₁ - 1₁ + 1 = 21/2² +2₂ 7 - +²₂+. 2g…

A: Volume flow rate: Q=0.015 m3/s Elevation difference: h=8.0m Suction line:…

Q: A force of 100N makes an angle Ɵ with the x-axis and has a y-component of 30N. Determine both the…

Q: If the system is released from rest, determine the speed of the 18 kg cylinder A after A has moved…

A: Given Mass, mB = 18 kg mA = 13 kg Distance, x = 4 m Find Velocity of B, vB

Q: Option: -SC plane 110 -SC plane 100 -FCC plane 111 -SC plane 111 -FCC plane 110 -BCC plane 100…

Q: 8-103. Blocks A and 8 have a mass of 100 kg and 150 kg. respectively. If the coefficient of static…

Q: Your answer is partially correct. Determine the forces in members BC, BE, and BF. The triangles are…

Q: is made of steel of 400mm². Use ne the vertical and A 1 m 2.5 kN -1 m E B D 1 m

Q: (7) Calculate the velocity v in branch a K₁ (P₁) Q₁ Qa Qb K₂ _m/s (P₂) Q2

Q: A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E =…

A: Series Combination:- Series combination of bars is a type of series where axial deflection is…

Q: 3.) What is the mass density (in lb/ft^3) of a liquid 2600 cm depth if the pressure is 2.2 MPa.

A: Given data: ◆ The depth of liquid level: h= 2600 cm = 26 m ◆ The pressure at this location: P = 2.2…

Q: A cylinder of radius R and mass M is tied to a rope that connects it to a box of mass m, through a…

Q: The solid shaft is loaded (two point loads) and supported (fixed at left end) as shown. For the xyz…

A: AS this Question as multiparts solving first part or you can mention the part Given data -: 1. dia…

Q: Determine the magnitude of the vertical force C, for the simply supported beam, where w = 11…

Q: In the equilibrium position shown, the resultant of the three forces acting on the bell crank passes…

A: To solve this problem, we need to first resolve the force P in horizontal and vertical direction.…

Q: Situation 5: A horizontal rigid boom OD is subjected to a vertical load P=1000 N and is supported by…

Concept explainers

Bending Moment

In general, we can define the bending moment as the reaction induced when a certain amount of load or force is applied to an element which makes it bend.

Question

For the simply supported beam subjected to the loading shown, derive equations for the shear force Vand the bending moment M
for any location in the beam. (Place the origin at point A.) Let a=2.75 m, b=5.00 m, PB = 60KN, and Pc = 80kN. Construct the shear-
force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO
exercise.
Answers:
Ay =
Dy=
tel
tel
a
i
B
a
Calculate the reaction forces Ay and Dy acting on the beam. Positive values for the reactions are indicated by the directions of the
red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.)
PB
B
a
PB
Pc
a
C
Pc
C
KN
b
KN
D
b
D
X
D₂
X

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Find expressions for shear force V and moment Mat x = 2L/3 of beam (a) in terms of peak load intensity q0and beam length variable L. Repeat for beam (b) but at x = L/2.
Find expressions for shear force V and moment M at mid-span of beam AB in terms of peak load intensity q0and beam length variables a and L Let a = 5L/b.
Find expressions for shear force V and moment Mat x = 2L/3 of beam (a) in terms of peak load intensity q0 and beam length variable L. Repeat for beam (b).
Find expressions for shear force V and moment M at x = x0of beam AB in terms of peak load intensity q0and beam length variable L. Let x0= 2L/3.
A counterclockwise moment M0acts at the midpoint of a fixed-end beam ACB of length L (see figure). Beginning with the second-order differential equation of the deflection curve (the bendingmoment equation), determine all reactions of the beam and obtain the equation of the deflection curve for the left-hand half of the beam. Then construct the shear-force and bending-moment diagrams for the entire beam, labeling all critical ordinales. Also, draw the deflection curve for the entire beam.
A beam ABCD with a vertical arm CE is supported as a simple beam at .1 and D (see figure). A cable passes over a small pulley that is attached to the arm at E. One end of the cable is attached to the beam at point B. The tensile force in the cable is 1800 lb. Draw the shear-Force and bending-moment diagrams for beam A BCD. Note: Disregard the widths of the beam and vertical arm and use centerline dimensions when making calculations. Repeat part (a) if a roller support is added at C and a shear release is inserted just left of C (see figure part b).
A fixed-end beam AB of a length L is subjected to a uniform load of intensity q acting over the middle region of the beam (sec figure). Obtain a formula for the fixed-end moments MAand MBin terms of the load q, the length L, and the length h of the loaded part of the beam. Plot a graph of the fixed-end moment MAversus the length b of the loaded part of the beam. For convenience, plot the graph in the following nondimensional form: MAqL2/l2versusbL with the ratio b/L varying between its extreme values of 0 and 1. (c) For the special case in which ù = h = L/3, draw the shear-force and bending-moment diagrams for the beam, labeling all critical ordinates.
For the beam AB shown in Cases 1 and 2, derive and plot expressions for the shear force and bending moment acting on section 1 in terms of the distance x (0 < x< L). [Note: Case 1 results in the conventional V- and M-diagrams, in which the loads are fixed and the location of the section varies; the diagrams for Case 2 (called influence diagrams) show the variation of V and M at a fixed section as the location of the load is varied]
Find support reactions at A and D and then calculate the axial force N. shear force 1 and bending moment 11 at mid-span of column BD. Let L = 4 m, q0 = 160N/m, P = 200N, and M0= 380 N .m.
A seesaw weighing 3 lb/ft of length is occupied by two children, each weighing 90 lb (see figure). The center of gravity of each child is 8 ft from the fulcrum. The board is 19 ft long, 8 in. wide, and 1.5 in. thick. What is the maximum bending stress in the board?
Cantilever beam AB carries an upward uniform load of intensity q1from x = 0 to L/2 (see Fig. a) and a downward uniform load of intensity q from x = L/2 to L. Find q1in terms of q if the resulting moment at A is zero. Draw V and M diagrams for the case of both q and qtas applied loadings. Repeat part (a) for the case of an upward triangularly distributed load with peak intensity q0(see Fig. b). For part (b), find q0, instead of q1
A square tube section has side dimension of 20 in. arid thickness of 0.5 in. If the section is used for a 10-ft-long beam subjected to 1250 kip-in, torque at both ends, calculate the maximum shear stress and the angle of twist between the ends. Use G = 11,600 ksi.