3. A built-up beam of box section as shown in Figure 3 is simply supported over a span of 3 m and carries a point load of 15 kN at 1 m from the end. The plate is attached to the channel by rivets pitched at 100 mm intervals. If the shear stress in the rivets must not exceed 50 MPa. 3.1 Determine a suitable rivet diameter (all dimensions are in mm) 150 10 10 -150- 10 30 30 10 10 10

3. A built-up beam of box section as shown in Figure 3 is simply supported over a span of 3 m and carries a point load of 15 kN at 1 m from the end. The plate is attached to the channel by rivets pitched at 100 mm intervals. If the shear stress in the rivets must not exceed 50 MPa. 3.1 Determine a suitable rivet diameter (all dimensions are in mm) 150 10 10 -150- 10 30 30 10 10 10

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.6.1P: A steel bar has a square cross section of width b = 2.0 in. (sec figure). The bar has pinned...

See similar textbooks

Similar questions

A vertical pole consisting of a circular tube of outer diameter 5 in. and inner diameter 4.5 in. is loaded by a linearly varying distributed force with maximum intensity of q0, Find the maximum shear stress in the pole.
Calculate the distance e from the cent crime of the web of a C 15 x 40 channel section to the shear center 5 (see figure). Note: For purposes of analysis, consider the flanges to be rectangles with thickness teequal to the average flange thickness given in Table F-3(a) in Appendix F.
The cross section of a slit square tube of constant thickness is shown in the figure. Derive the following formula for the distance e from the corner of the cross section to the shear center S: e=b22
A steel bar has a square cross section of width b = 2.0 in. (sec figure). The bar has pinned supports at the ends and is 3.0 ft long. The axial forces acting at the end of the bar have a resultant P = 20 kips located at distance e = 0,75 in, from the center of the cross section. Also, the modulus of elasticity of the steel is 29,000 ksi. Determine the maximum compressive stress max, in the bar. If the allowable stress in the steel is 18,000 psi, what is the maximum permissible length Lmaxof the bar?
A circular pole is subjected to linearly varying distributed force with maximum intensity t0. Calculate the diameter daof the pole if the maximum allowable shear stress for the pole is 75 M Pa.
A steel post /t if with a hollow circular cross section is fixed at the base and free at the top (see figure). The in net and outer diameters arc d1= 96 mm and d2= 110 mm, respectively, and the length is L = 4.0 m. A cable CED passes through a fitting that is welded to the side of the post. The distance between the plane of the cable (plane CBD) and the axis of the post is e = 100 mm, and the angles between the cable and the ground arc a = 53.13º. The cable is preten-sioned by tightening the turn buck les. If the deflection at the top of the post is limited to = 20 mm, what is the maximum allowable tensile force Tin the cable? (Assume E = 205 GPa.)
A flying but tress transmit s a load P = 25 kN, acting at an angle of 60º to the horizontal, to the top of a vertical buttress AB (see figure). The vertical buttress has height h = 5.0 m and rectangular cross section of thickness t = 1.5 m and width b = 1.0 m (perpendicular to the plane of the figure). The stone used in the construction weighs y = 26 kN/m3. What is the required weight W of the pedestal and statue above the vertical buttress (that is, above section A) to avoid any tensile stresses in the vertical buttress?
The cross section of a narrow-gage railway bridge is shown in part a of the figure. The bridge is constructed with longitudinal steel grinders that support the wood cross ties. The bridge is constructed with longitudinal steel girders that support the wood cross ties. The girders are restrained against lateral buckling by diagonal bracing, as indicated by the dashed lines. The spacing of the girders is S1= 50 in. and the spacing of the rails is s2= 30 in. The load transmitted by each rail to a single tie is P = 1500 1b. The cross section of a tie, shown in part b of the figure, has a width b =5.0 in. and depth d. Determine the minimum value of d based upon an allowable bending stress of 1125 psi in the wood tie. (Disregard the weight of the tie itself.)
Calculate the distance e from the centerline of the web of a C 310 × 45 channel section to the shear center E (see figure). Note: For put poses of analysis, consider the flanges to be rectangles with thickness îrequal to the average flange thickness given in Table F-3(b) in Appendix F.
Two W 310 × 74 Steel wide-flange beams are bolted together to form a built-up beam as shown in the figure. What is the maximum permissible bolt spacing s if the shear force V = 80 kN and the allowable load in shear on each bolt is F = 13.5 kN. Note: Obtain the dimensions and properties of the W shapes from Table F-l(b).
A pole is fixed at the base and is subjected to a linearly varying distributed force with maximum intensity of q0and an axial compressive load P = 20 kips at the top (see figure). The pole has a circular cross section with an outer diameter of 5 in. and an inner diameter of 4.5 in. Find the normal stresses on the surface of the pole at the base at locations A and B.
A vertical pole of aluminum is fixed at the base and pulled at the top by a cable having a tensile force T(see figure). The cable is attached at the outer edge of a stiffened cover plate on top of the pole and makes an angle a = 20° at the point of attachment. The pole has length a = 2.5 m and a hollow circular cross section with an outer diameter d2= 280 mm and inner diameter d1= 220 mm. The circular cover plate has diameter 1.5d2 Determine the allowable tensile force Tallow in the cable if the allowable compressive stress in the aluminum pole is 90 MPa.