3. A very light rod of length 3L is pivoted at one end so it can rotate without friction on a flat table top. A mass M is attached to the rod a distance L from the pivot and a second mass 2M is attached to the opposite end from the pivoted end as shown in the figure. What is the ratio of the tension T1 to T2 ? That is, calculate T1/T2. шк 2M 3L M w Pivot Point

3. A very light rod of length 3L is pivoted at one end so it can rotate without friction on a flat table top. A mass M is attached to the rod a distance L from the pivot and a second mass 2M is attached to the opposite end from the pivoted end as shown in the figure. What is the ratio of the tension T1 to T2 ? That is, calculate T1/T2. шк 2M 3L M w Pivot Point

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter8: Rotational Equilibrium And Dynamics

Section: Chapter Questions

Problem 39P: A large grinding wheel in the shape of a solid cylinder of radius 0.330 m is free to rotate on a...

See similar textbooks

Similar questions

What is- the magnitude of the angular acceleration of a 25.0-kg disk of radius 0.800 m when a torque of magnitude 10.0 N m is applied to it? (See Section 8.5.)
An automobile engine can produce 200 N m of torque. Calculate the angular acceleration produced if 95.0% of this torque is applied to the drive shaft, axle, and rear wheels of a car, given the following information. The car is suspended so that the wheels can turn freely. Each wheel acts like a 15.0 kg disk that has a 0.180 m radius. The walls of each tire act like a 2.00-kg annular ring that has inside radius of 0.180 m and outside radius of 0.320 m. The tread of each tire acts like a 10.0-kg hoop of radius 0.330 m. The 14.0-kg axle acts like a rod that has a 2.00-cm radius. The 30.0-kg drive shaft acts like a rod that has a 3.20-cm radius.
Find the net torque on the wheel in Figure P10.23 about the axle through O, taking a = 10.0 cm and b = 25.0 cm. Figure P10.23
Two window washers. Bob and Joe, are on a 3.00-m-long, 345-N scaffold supported by two cables attached to its ends. Bob weighs 750 N and stands 1.00 m from the left end, as shown in Figure P8.82. Two meters from the left end is the 500-N washing equipment. Joe is 0.500 m from the right end and weighs 1 000 N. Given that the scaffold is in rotational and translational equilibrium, what are the forces on each cable? Figure P8.82
Three identical thin rods, each of length L and mass m, are welded perpendicular to one another as shown in Figure P10.43. The assembly is rotated about an axis that passes through the end of one rod and is parallel to another. Determine the moment of inertia of this structure about this axis.
A large grinding wheel in the shape of a solid cylinder of radius 0.330 m is free to rotate on a friction less, vertical axle. A constant tangential force of 250. N applied to its edge causes the wheel to have an angular acceleration of 0.940 rad/s2. (a) What is the moment of inertia of the wheel? (b) What is the mass of the wheel? (c) If the wheel starts from rest, what is its angular velocity after 5.00 s have elapsed, assuming the force is acting during that time?
Four objectsa hoop, a solid cylinder, a solid sphere, and a thin, spherical shelleach have a mass of 4.80 kg and a radius of 0.230 m. (a) Find the moment of inertia for each object as it rotates about the axes shown in Table 8.1. (b) Suppose each object is rolled down a ramp. Rank the translational speed of each object from highest to lowest, (c) Rank the objects rotational kinetic energies from highest to lowest as the objects roll down the ramp.
A large grinding wheel in the shape of a solid cylinder of radius 0.330 m is free to rotate on a friction less, vertical axle. A constant tangential force of 250. N applied to its edge causes the wheel to have an angular acceleration of 0.940 rad/s2. (a) What is the moment of inertia of the wheel? (b) What is the mass of the wheel? (c) If the wheel starts from rest, what is its angular velocity after 5.00 s have elapsed, assuming the force is acting during that time?
A uniform solid disk and a uniform hoop are placed side by side at the top of an incline of height h. (a) If they are released from rest and roll without slipping, which object reaches the bottom first? (b) Verify your answer by calculating their speeds when they reach the bottom in terms of h.
A rigid body is rotating counterclockwise about a fixed axis. Each of the following pairs of quantities represents an initial angular position and a final angular position of the rigid body. Which of the sets can occur only if the rigid body rotates through more than 180? (a) 3 rad, 6 rad; (b) 1 rad, 1 rad; (c) 1 rad, 5 rad.
A grinding wheel is in the form of a uniform solid disk of radius 7.00 cm and mass 2.00 kg. It starts from rest and accelerates uniformly under the action of the constant torque of 0.600 N m that the motor exerts on the wheel. (a) How long does the wheel take to reach its final operating speed of 1 200 rev/min? (b) Through how many revolutions does it turn while accelerating?
A solid, uniform disk of radius 0.250 m and mass 55.0 kg rolls down a ramp of length 4.50 m that makes an angle of 15.0 with the horizontal. The disk starts from rest from the top of the ramp. Find (a) the speed of the disks center of mass when it reaches the bottom of the ramp and (b) the angular speed of the disk at the bottom of the ramp.