Answered: 3. Determine the torsional spring…

3. Determine the torsional spring constant of the steel propeller shaft shown in Figure 2. |A В 0.3 m 0.2 m 0.25 m 0.15 m В -2 m -3 m² Figure 2. Propeller shaft

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.2.15P: Repeat Problem 11.2-14 using L = 12 ft, ß = 0.25 kips/in., ßRl= 1.5ßL2, and ßR2= 2 ßR1.

See similar textbooks

Related questions

Q: (a) Determine the support reactions for the stepped circular shaft shown below. (b) Plot the…

A: GIVEN :- T1=200lb-inT2=100lb-inT3=500lb-indAB=3 indCE=2 inE=30×106psiμ=0.3SOLUTION :-Torque on…

Q: 4. When unloaded, bars AB and AC are each 36 -in long and have a cross-sectional area of 2 in. Their…

Q: An aluminum [E = 10,000 ksi] control rod with a circular cross section must not stretch more than…

A: F=2100lb d=0.372in

Q: 4. A 100-N weight causes a spring to stretch an unknown distance, h. The addition of a weight of 250…

Q: a. A mass M of 200 kg is dropped onto the rigid member AB as shown in Figure 3. Assuming that 75…

Q: A closely coiled helical spring is to carry a load of 500N. Its mean coil diameter is to be 10 times…

A: Springs are one of the flexible machine elements, which gets deformed when load is applied to it and…

Q: A composite rod of 160 mm in length, is composed of 50 mm in diameter for a length of 100 mm and 30…

A: *As per our guidelines we are supposed to answer first three sub-parts of the question. Kindly…

Q: The bent rod shown in (Figure 1) is supported at A, B, and C by smooth journal bearings. The…

A: Given, Cx = 61 N

Q: An open coiled helical spring is subjected to an axial load of 50 kN. Determine the deflection of…

A: Write the given data. W=50000 Nn=4R=30 mm=0.030 md=0.005 mG=80000×106 Paα=10°E=2×1011 Pa

Q: A hollow aluminium shaft of 80 mm outer diameter & 60 mm inner diameter is rotating @ 5 Hz when…

Q: 1.24 Find the length of the equivalent uniform hollow shaft of inner diameter d and thickness / that…

A: Solution: here l2 is the hallow shaft solid conical shaft length 'l' is show in…

Q: The shaft of a motor has a length of 15 times its diameter and has a maximum twist of 1.5 degrees…

A: Given: The length of shaft of motor, L = 15d The maximum twist in shaft = 1.5o The torque applied, T…

Q: LA load F of 500 N is applied in the negative x-direction on rod OA, and a load P of 200 N is…

A: Given: The load, F = 500 N The force at B, P = 200 N

Q: If an isotropic material has a shear modulus of 30 Gpa and a Poisson's ratio of 0.34, calculate its…

Q: A vertical shaft of 5 mm diameter is 200 mm long and is supported in long bearings at its ends. A…

Q: A spring with 25 active coils cannot be accommodated within the given space, hence 5 coils were cut.…

Q: If an isotropic material has a shear modulus of 27 Gpa and a Poisson's ratio of 0.42, calculate its…

Q: Problem 1 In the structure shown below, all three bars have the same A, E, L. Using the Theorem of…

A: Given that we have to use theorem of minimum potential energy.

Q: 3. Shafts AB and BC (each 50 mm long) are welded to each other. Shaft AB is hallow with 20 mm inner…

A: Given data: The outer diameter of the shaft AB is DAB=30 mm The inner diameter of the shaft AB is…

Q: 15 mm diameter shaft rotates in long fixed bearings 60 cm apart. A rotor of mass 20 kg is mounted at…

A: Given: The diameter of shaft, d = 15 mm The length of shaft, L = 60 cm The mass of rotor, m = 20 kg…

Q: ine the mazimum shearing stress (using approximate and exact equations) and elongation of a helical…

A: Given:n=22d=15 mmD=100 mmF=1.3 KNG=83 GPa

Q: Determine to the nearest millimeter the minimum diameter of the solid shaft if it is subjected to…

A: Given: The allowable strength of the material, Sall = 150 MPa Consider x-z plane, The maximum…

Q: Find the diameter of the shaft (based on torsional stiffness) for which the angle of twist is not to…

Q: Determine the equivalent spring stiffness constant of the following spring in series and parallel.…

Q: 5.6 A vertical close-coiled helical compression spring must have a stiffness of 900 N/m under a load…

A: k=Stiffness of Spring=900 N/mP=load=45 Nσmax=Maximum load=120 MPaG=Shear Modulus=40 GPah=Vertical…

Q: A helical spring in which the mean diameter of the coil is 8 times the wire diameter is to be…

A: Given data: Calculate the spring index as follows: Write the expression to calculate the Wahl…

Q: A semi-elliptic leaf spring used for automobile suspension consists of three extra full-length…

A: Given data2P=75 KN2L=1 mb=atnf=3ng=15E=20700 mPaσb=450 Nmm2

Q: Determine the equivalent spring stiffness constant of the following spring in series and parallel.…

Q: 2. A close -coiled helical spring having 12 coils must absorb 200 joules of energy and support a…

A: Given data⇒n=12 coilsE=200 joulesF=10 kNζ=220 MPaG=80 GPaProblem definition⇒Problem says determine…

Q: A 50 kg drum is suspended by a rope below a ring A, as shown below. The ring is supported by another…

A: To determine the unstretched length of spring.

Q: 40 Steel d = 30 mm A G= 83 GPa 1.2 m

A: Calculated resisting torque at support at A and B .

Q: M2 N (Steel tame) =60 loN/m: K2=45 N/m K3=30 k/m : M,70 kg : M2=140 kg Figure P8 M Problem 9 Figure…

A: other subject of mass m by x amount from equlibrium position-Kinetic energy-K.E=12mx2 x=dxdt

Q: Do fast

Q: Shaft AB is 3 meter long and is free at the left end and fixed torsionally at the right end. It is…

A: Given:

Q: A load P is supported by two springs arranged in series. The upper spring has 20 turns of 19 mm…

Q: 1 N/mm, 495 N/mm, 541 N/mm respectively. Determine the equivalent spring constant if the springs are…

A: given:k1=641N/mmk2=495N/mmk3=541N/mm

Q: The b xd xhrubber blocks shown are used in a double U shear mount to isolate the vibration of a…

Q: A simple diagram of a driveshaft ABC is shown in Figure 3. The power generated by an engine is…

Q: 1 A hollow shaft with outside diameter of 14 cm and wall thickness of 0.8 cm transmits 200 kW at 400…

Q: The line joining ou (ultimate strength of the material) on mean stress axis and oe (endurance limit…

Q: 3. The free length of the plain ends spring is equal to (where: Na = the number of active coils, P =…

Q: 300 N m 45mm 09m 44 mm 1.2m 40mm

Q: 01: A hollow steel tube (1) with an outside diameter of 2.75 in. and a wall thickness of 0.25 in, is…

A: Solution: Force acting at A can be found by, FA-34+18-25=0FA=-41kips Free body diagram of each…

Q: 1. A rod of length 1.50 m and diameter 0.12 m is mounted in a rigid wall. A vertical bar of length…

A: Note:- As per our company guidelines we are supposed to answer only the first three sub-parts.…

Q: 1.39 Find the spring constant of the bimetallic bar shown in Fig. 1.89 in axial motion. 2 cm -Steel,…

Q: The rod is supported by smooth journal bearings at A, B, and C and is subjected to the two forces F1…

Q: The 16 x 22 x 25-mm rubber blocks shown in the figure are used in a double U shear mount to isolate…

Q: Determine the equivalent torsional spring constant of the system that will be located in the…

A: Given data: The value of spring constant is, k=1.5 N/m. The length of the bar or rod is, l=2 m.

Q: A hollow aluminium shaft of 80 mm outer diameter & 60 mm inner diameter is rotating @ 5 Hz when…

Concept explainers

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing. 

Question

3.
Determine the torsional spring constant of the steel propeller shaft shown in Figure 2.
|A
В
0.3 m
0.2 m
0.25 m
-0.15 m:
В
-2 m
3 m
Figure 2. Propeller shaft

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the minimum force required to deflect the spring with spring constant of 251 N/mm to a displacement of 5 mm.
A semi-elliptic spring used for automobile suspension, consists of twoextra full-length leaves and eight graduated-length leaves, including themaster leaf. The centre-to-centre distance between the two eyes is 1 m.The leaves are made of steel 55Si2Mo90 (S = 1500 N/mm yt2 andE = 207 000 N/mm2) and the factor of safety is 2. The maximum springload is 30 kN. The leaves are pre-stressed so as to equalize stresses in allleaves under maximum load. Determine the dimensions of thecross-section of the leaves and the deflection at the end of the spring.
A spring has a load of 50 lb with a spring index of 8. If the induced stress is 90ksi, determine the wire diameter.
An open coiled helical spring is subjected to an axial loadof 50 kN. Determine the deflection of the spring andmaximum shear stress in the spring wire. The springparticular are as follows:(i) No. of coils = 4(ii) Mean radius of coil 30 mm(iii) Diameter of the spring wire = 5 mm(iv) Modulus of rigidity = 80000 MPa(v) Angle of helix = 10"(vi) Young's modulus, E = 2 x 105 N/mm²
A rod has a diameter of 1/2 inch and a length of 4 feet. Determine the equivalent spring constant of the rod in pounds per foot. (E=10x10^6 psi)
A closely coiled helical spring is to carry a load of 500N. Its mean coil diameter is to be 10 times that of the wire diameter. Calculate these diameters if the maximum shear stress in the material of the string is to be BOMN/m*2.
A helical compression spring is to be used for a maximum load of 1.5 kN using the spring index of 8. The maximum permissible shear stress for the spring wire is 400 MPa. Which of the following is the wire diameter of the spring to be used?
An 18 coils helical spring having a load of 100kg. The modulus of elasticity in shear of spring is 96.62 GPa, OD of 9.256 cm and with wire diameter of 9.525 mm. The spring is squared and ground ends. Compute for the following respectively: 1) number of effective coils2) spring index3) axial load (N) 4) deflection (mm) Answers must be at least in 4 decimal places.
A hand cranking lever, as shown in Figure 6 below, is used to start a truck engine byapplying a force F = 400 N. The material of the cranking lever has a yield strength = 320 MPa;Ultimate tensile strength = 500 MPa; Young’s modulus = 205 GPa; Modulus of rigidity = 84 GPaand poisson’s ratio = 0.3. Assuming factor of safety to be 4 based on yield strength, design thediameter of the lever at section X-X near the guide bush using: a) Maximum distortion energytheory; and b) Maximum shear stress theory.
(5) A gas engine valve spring is loaded to 35kgf when the valve is closed & 52kgf hen the valve is open. The valve lift is 8mm. The outside diameter is to be from 38mm~45mm, & the permissible stress is 413N/mm2 . Determine: (a) the wire & outside diameter; (b) the number of effective coils; (c) the free length when it is squared & ground.
Determine the possible range for R is the equivalent spring stiffness constant varies from 50 N/m to 500 N/m
The helical compression spring is made of 12mm wire diameter with 132 mm mean diameter. Determine stiffness of the spring when modulus of rigidity G=80 kN/mm2,number of turn is 13 and axial load is 190N.