A hollow aluminium shaft of 80 mm outer diameter & 60 mm inner diameter is rotating @ 5 Hz when constant 120 KW is applied. Use the following: G(alum)=28 GPa, a=1.80 m, b=0.80m & L=2.60 m. Assumed that the angle of twist is constant. The torque "T1" developed at left fixed support at a is____KN-m (A) 5.03 B) 3.82 C) 2.64 (D) 0.48 (E) 1.18

A hollow aluminium shaft of 80 mm outer diameter & 60 mm inner diameter is rotating @ 5 Hz when constant 120 KW is applied. Use the following: G(alum)=28 GPa, a=1.80 m, b=0.80m & L=2.60 m. Assumed that the angle of twist is constant. The torque "T1" developed at left fixed support at a is____KN-m (A) 5.03 B) 3.82 C) 2.64 (D) 0.48 (E) 1.18

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.10P: What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm,...

See similar textbooks

Similar questions

A full quarter-circular fillet is used at the shoulder of a stepped shaft having diameter D2= 1.0 in. (see figure), A torque T = 500 lb-in. acts on the shaft. Determine the shear stress at the stress concentration for values as follows: D1= 0.7,0.8, and 0.9 in. Plot a graph showing versus D?
What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
QUESTION 7 Figure 7 shows an assembly consist of circular shaft AB, solid circular BC and a circular CE. The shaft is made of titanium alloy steel and fixed at A. Segment AB is a hollow shaft, has an inner diameter of 25mm. While tube CE with the thickness 2mm has an outer diameter of 20mm. The assembly is subjected to torques of 1000 Nm at C, 210 m at D and 350 Nm at E. The alloy has modulus of rigidity, G = 44kN/mm^2 a) Draw the torque diagram of the shaft. b) Determine maximum shearing stress developed in each segment. c) Calculate the angle of twist at the right end of the shaft.
Design the outside and inside diameters for a hollow stell shaft subjected to a torque of 1,000,000 in-lb. The maximum shear stress developed in the shaft is not to exceed 8,000 psi. The inside diameter is to be 2/3 of the outside diameter. Calculate the angle of twist in degrees for a 14 foot length of this shaft. Answer: D(outside) = 9.259 inches, D(inside) = 6.176 inches, angle of twist= 1.39 degrees I'm unsure of how to solve this problem. Could someone help me walk through the process step-by-step? Thanks in advance.
A shaft with a hollow cross section is subjected to torque of magnitude T = 5.5 kN-m. If the outer diameter of the shaft is 0.1 m and its wall thickness is 10 mm, what would be the minimum diameter of a solid steel shaft needed if it would be subjected to the maximum shear stress of the hollow shaft?
A hollow circular bar has an inner radius r1 and an outer radius r2. if r1=r2/2, most nearly what percentage of torque can the shaft carry in comparison with a solid shaft?
Design a hallow shaft (Diameter and length) that develops 80 kW of power while rotating at a speed of 4000 rpm. The design constrains are as under:The angle of twist not to exceed 0.200Shear stress is not to exceed 480 MN/m2The outer diameter is to be twice the inner diameter. The shaft length is to be three times the outer diameter. Modulus of rigidity = 79 GN/m2.
Figure Q1 shows a shaft AB (modulus of rigidity G = 73 GPa) with a total length of 1270 mm that is fixed at both ends. Section AC is solid with a diameter of do = 80 mm, while CB is a hollow section with an internal diameter of di = 60 mm. An external torque T0 = 10 kN.m is applied at point D. B) What is the maximum angle of twist, max and where does it occur?
A hollow shaft is to transmit 390 kW at 70 rpm. If the shear stress is not to exceed 45 MPa and the diameter ratio is 0.58, Design the shaft by assuming the maximum torque is 40% greater than its mean torque. (i) The mean torque is (Unit is in Nm)= (ii) The maximum torque is (Unit is in Nm iii) The outer diameter of the shaft (unit in mm) (iv) The inner diameter of the shaft (unit in mm
A shaft in torsion only is to transmit 2500 hp at 570 rpm. Its material’s allowable shear stress is 10 ksi. (a) What should be the diameter of a solid shaft? (b) If the shaft is hollow, Do = 2Di, what size is required? (c) Which is the lighter? By what percentage? (d) Which shaft is the more rigid? PLEASE I NEED IT ASAP . THANK YOU
A hollow shaft of outer diameter 40 mm and inner diameter of 20 mm is to be replaced by a solid shaft to trandmit the same torque at the same maximum stress. What should be the diameter of the solid shaft?
(7) The drive of an outboard motor which rotates @ 5,000rpm is supported by a spline in the crankshaft @ the upper end & bearing @ the lower end 560mm apart. (a) If the engine develops 15kW @ this speed, what is the diameter of the solid steel shaft to use? The allowable torsional stress is 80N/mm2 .