A simple diagram of a driveshaft ABC is shown in Figure 3. The power generated by an engine is transmitted via the drive shaft, ABC. The section AB is a solid circular shaft 0.7 m long and the section BC is a hollow circular shaft 1.0 m long with 110 mm outer diameter and 55 mm inner diameter. Both shafts are made from a metal alloy (Shear Modulus G = 95 GPa). 0.7 m 1.0 m A в 2400 hp @ 2000 rpm Figure 3 a) If the drive shaft rotates at 2000 rpm and the power transmitted along the shaft is 2400 hp (1 hp = 745.7 W), calculate the torque developed in the drive shaft.

A simple diagram of a driveshaft ABC is shown in Figure 3. The power generated by an engine is transmitted via the drive shaft, ABC. The section AB is a solid circular shaft 0.7 m long and the section BC is a hollow circular shaft 1.0 m long with 110 mm outer diameter and 55 mm inner diameter. Both shafts are made from a metal alloy (Shear Modulus G = 95 GPa). 0.7 m 1.0 m A в 2400 hp @ 2000 rpm Figure 3 a) If the drive shaft rotates at 2000 rpm and the power transmitted along the shaft is 2400 hp (1 hp = 745.7 W), calculate the torque developed in the drive shaft.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.9P: A propeller shaft of solid circular cross section and diameter d is spliced by a collar of the same...

See similar textbooks

Similar questions

A stepped shaft ABC consisting of two solid, circular segments is subjected to torques T}and T2acting in opposite directions, as shown in the figure. The larger segment of the shaft has a diameter of dv- 2.25 in. and a length Lt= 30 in.; the smaller segment has a diameter d2— 1.75 in. and a length L, = 20 in. The torques are T, = 21,000 lb-in. and fz=10.000 lb-in. (a) Find reaction torque TAat support A. (b) Find the internal torque T(x) at two locations: x = L1/2 and x = L1+ L2/2. Show these internal torques on properly drawn free-body diagrams (FBDs).
A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The inside diameter of the shaft is to be one-half of the outside diameter. If the allowable shear stress in the shaft is 45 MPa, what is the minimum required outside diameter d?
A propeller shaft of solid circular cross section and diameter d is spliced by a collar of the same material (see figure). The collar is securely bonded to both parts of the shaft. What should be the minimum outer diameter dyof the collar in order that the splice can transmit the same power as the solid shaft?
A bumping post at the end of a track in a railway yard has a spring constant k = 8.0 MN/m (see figure). The maximum possible displacement d or the end of the striking plate is 450 mm. What is the maximum velocity vmaxthat a railway car of weight W = 545 kN can have without damaging the bumping post when it strikes it?
A stepped shaft ABC consisting of two solid, circular segments is subjected to uniformly distributed torque t1acting aver segment 1 and concentrated torque t2applied at C, as shown in the figure. Segment 1 of the shaft has a diameter of d1= 57 mm and length of L1= 0.75 m; segment 2 has a diameter d2— 44 mm and length L2= 0.5 m. Torque intensity /,"= 3100 N . m/m and T2= 1100 N. m. (a) Find reaction torque TAat support A. (b) Find the internal torque T(x) at two locations: .x = L1/2 and at .x = L1+ L2/2. Show these internal torques on properly drawn free-body diagrams.
A solid steel shaft 4.5 m long is stressed at 75 MPa when twisted through 4.5°. What power can be transmitted by the shaft at 25 Hz? Use G = 83 GPa.
A motor (located at C) provides 50kW of power which is then used by pulleys A and B. When the motor is running, the transmission shaft (which is made of Cr-Ni steel and has a diameter of 5cm) starts rotating at a speed of 200 rpm. 1) Find the moment of force at pulleys A, B and C. 2) Find the torque in each section (between the pulleys). 3) What is the safety factor of the driveshaft on the ultimate limit?
A shaft ABC rotates at 500rpm and is driven through a coupling at the end A. At B a pulley takes off two-third of the power, the remainder being absorbed at C. The part AB is 1.5m long and of 100mm diameter, BC is 2m long and of 75mm diameter. The maximum shear stress set up in BC is 40MPa. Determine the maximum stress in AB and the power transmitted by it, and calculate the total angle of twist in the length AC. Take G = 80GPa.
A horizontal nickel steel shaft shown in the below Figure rests on two bearings, A at the left and B at the right end and carries two gears C and D located at distances of 250 mm and 400 mm respectively from the centre line of the left and right bearings. The diameter of the gear C is 600 mm and that of gear D is 200 mm. The distance between the centre line of the bearings is 2400 mm. The shaft transmits 20 kW power at 120 r.p.m. The power is delivered to the shaft at gear C and is taken out at gear D in such a manner that the tooth force Fic of the gear C and FID of the gear D act vertically downwards. The gear C and D weighs 950 N and 350 N respectively. The combined shock and fatigue factors for bending and torsion may be taken as 1.5 and 1.2 respectively. (iii) Determine the maximum moment acting on the shaft
The disc clutch of an automobile is carried on a 2-inch 6-splined shaft and not to slide under load. The nominal dimensions are as follows: b = 0.25 D; t = 0.075 D and d = 0.85 D. The hub length of 150 % of shaft diameter. Determine the total horsepower transmitted at 3,600 rpm, if the yield strength of the shaft is 1,400 psi
A V-belt drive transmits 20kW from an electric motor running at 1440rpm to the main shaft of a roving machine. The motor and main shaft pulleys have 300 & 600 rpm respectively. The coefficient of friction between belt and pulley is 0.25. The centre distance between the shafts is 1000mm. The top width, thickness, section angle and density of belt and permissible tension on the belt are 22mm, 14mm and 40deg, 0.97gcm-2 and 600N respectively. How many belts are needed? Calculate the length of a belt needed
A keyed sprocket delivers a torque of 778.8 N - m thru the shaft of 54 mm OD. The key thickness is 1.5875 cm and the width is 1.11 cm. Compute the length of the same key. The permissible stress value of 60 MPa for shear and 90 MPa for tension. A. 39.12 cm B. 4.82 cm C. 52.22 cm D. 4.32 cm