3. In the circuit shown in Figure, the total current is 150 mA and the current through the inductor is 100 mA. Determine what the applied voltage is. Also, knowing that the frequency is 50 Hz, find the value of L. 150 mA 100 mA 50 Hz 100 2

3. In the circuit shown in Figure, the total current is 150 mA and the current through the inductor is 100 mA. Determine what the applied voltage is. Also, knowing that the frequency is 50 Hz, find the value of L. 150 mA 100 mA 50 Hz 100 2

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter18: Resistive-inductive Parallel Circuits

Section: Chapter Questions

Problem 2PP: Assume that the current flow through the resistor, IR, is 15 A; the current flow through the...

See similar textbooks

Related questions

Q: :Answer a or b:- a) A variable capacitance and a resistance of 160 Q are connected in series across…

A: In this question, Variable capacitance connected in series with resistance R= 160 ohm Draw the…

Q: Find the following. (In the figure, use C, = 33.20 µF and C, = 27.20 µF.) %3D 6.00μ Cz µF 9.00 V (a)…

A: Fig: Given circuit (a) equivalent capacitance is given by…

Q: The current in a 150 pH inductor is : İL = 25te500t A for t> 0. %3D

Q: The two capacitors in the figure were charged and then connected as shown. Determine (a) the…

A: In this question we need to find a following

Q: Vi 180290 V %3D L = 30jN e C,=-30jN %3D C1 L1 A lll R1 V1 15 Q

Q: The circuit shown below has the following parameters: C1 = 9 µF, C2 = 4 µF, C3 = 13 µF and V = 140…

Q: A coil of resistance R and inductance L is connected in series with a 50 μF capacitor, figure If the…

A: In this question we need to find a value of R and L , voltage across coil and capacitor.

Q: For the inductor group below, determine the equivalent inductance: L1 L2 12mH OmH L3 OmH

A: In this question, find the equivalent inductance across the terminal. We are solving this problem…

Q: In an L-R-C series circuit, the source has a voltage amplitude of 121 V , R = 75.0 Ω , and the…

A: VS=121 VR=75 ΩXC=475 ΩVC=358 V (A). Relation between voltage and current across capacitor,…

Q: (a) What is the total impedance of an inductor with a reactance 150 Q when connected to the…

A: We are authorized to answer one question at a time, so we are answering the first one, please repost…

Q: (a) The value of the inductor in µH. (b) The value of the capacitor in nF. (c) The impedance…

A: Given the parallel tuned circuit, Resonance frequency, fr=500 kHz Bandwidth, B.W. = 20 kHz Coil…

Q: In the figure given below V = 9.0 V, C = C2 = 30 µF, and C3 = C4 = 15 µF. What is the charge on…

Q: 4) Analyze the circuit given below to determine the charge stored in capacitor C4. C2 2uF C1 12UF C5…

Q: Given the waveform of the current in a 3H inductor as shown in Figure below, determine the inductor…

Q: Given the shown waveforms of the inductor's voltage and current, find 30V the inductance L 1A 1(ms)…

A: Given: waveform for voltage and current through an inductor To find the value of inductance L = ?

Q: A coil of resistance R and inductance L is connected in series with a 50 μF capacitor, figure If the…

Q: In a RC charging circuit, given R = 100 Kohm, Supply voltage = 12 V and voltage across the capacitor…

A: In this question RC charging circuit is given with supply voltage and resistance value....Given…

Q: A variable capacitor C (see left photograph at the bottom of the diagrams for this assignment) is…

A: When the battery is disconnected from the capacitor, the capacitor will be charged. When the charged…

Q: The voltage across a 200-mH inductor is given by v = 3t2 + 2t + 4V. Determine the current through…

Q: A capacitor is connected into a 1250-V, 1000-Hz circuit. The current flow is 80 A. What is the…

A: Given data, The value of voltage is V = 1250 V. The value of frequency is f = 1000 Hz. The value of…

Q: H.W: for the circuit shown in figure find: (a) the charge in each capacitor. (b) The total charge.…

A: In this question, We need to determine the charge in each capacitor, total charge, equivalent…

Q: Apply combinatorial techniques as appropriate to obtain a value for the equivalent inductance Leg as…

Q: Problem 3 A capacitor shown in the following figure discharges into a load resistor. The capacitor…

Q: Basic Electrical Engineering: Inductance and Capacitance You are an electrician working in an…

A: The AC capacitors are polarity-independent and non-polarized. As a result, an AC capacitor may be…

Q: Find the equivalent inductance in the given circuit, where each L = 10 H and L1 = 37 H

A: If two inductors are connected in parallel than equivalant inductance is (L1×L2)/(L1+L2) If they are…

Q: write the Nodal equations; b.) solve for V1 (left of the inductor) and V2 ( right of the inductor)…

Q: For the given voltage across a 3 H inductor, plot the current and power waveforms assuming an…

A: It had been given that the initial inductor current is zero. The inductor current equation has been…

Q: 3. The current through a 10-mH inductor is shown in the figure below. Determine the voltage across…

A: In this question, we need to determine the voltage across the Inductor? We know V= L di/dt

Q: 30. The equivalent circuit of an inductor in a steady-state condition. a. Open b. Short 31.…

A: An electric elements such as inductor is said to be in steady state when current across the inductor…

Q: What is the equivalent capacitance of the following circuit?

A: If two capacitors C1 and C2 are connected in series than equivalent capacitance is( C1×C2) /(C1+C2…

Q: 1.W: for the circuit shown in figure find: (a) the charge in each capacitor. (b) The energy in each…

A: As per the guidelines of bartleyby I need to answer first three subparts only so kindly repost other…

Q: This diagram describes the work associated with an inductor of 20 mH, the voltage drop on the…

Q: Problem 4 capacitor shown in the following figure is charged through a load resistor using a voltage…

A: In this question we will solve series RC circuit...

Q: H.W: for the circuit shown in figure find: (a) the charge in each capacitor. (b) The total charge.…

Q: Apply combinatorial techniques as appropriate to obtain a value for the equivalent inductance Leg as…

A: To solve above problem, one should know how to find equivalent inductance for series and parallel…

Q: The voltage across a 2 (mH) inductor is shown in the top-left plot below. Assuming i¿ (0) = 0,…

A: The voltage across a 2 mH inductor is shown in the top-left plot below. Assuming iL(0)=0, we need to…

Q: Q2: Find the voltage in all capacitor in figure below where the capacitance in uF C1 300 200 C4 400v…

Q: C2 luf Ci 4uF C3 3uF P C4 6uF C6 8uF C5 2uF

Q: The two capacitors in the figure were charged and then connected as shown. Determine (a) the…

A: In this question we will find equivalent capacitance , equivalent voltage at terminals and energy…

Q: (b) Find the equivalent inductance of the circuit in Figure Q3(b). 8mH 6mH a 5mH 12mH 8mH 4mH 6mH…

A: In this question we will turn equivalent inductance across point ab...

Q: Problem 2) The current in a 50 mH inductor is given as the following: i(t)= 2t D0 Determine the…

Q: C3 C3 C3 C2 +C2 C3 d C3 C3 C3

A: For a capacitor we know that two capacitor of equal value are connected in series then their…

Q: H.W: for the circuit shown in figure find: (a) the 12uF 4uF charge in each capacitor. (b) The energy…

A: In this question, We need to charge on each capacitance, energy on each capacitors? And also find…

Q: A 100 mH inductor has an initial current of 10 A and a voltage across it of –900e–750t V, what is…

Q: A pure inductance of L = 152 mH is connected to a V = 106 V, 50 Hz supply. The current taken by the…

A: Given data : V= 106 VL=152 mH =0.152 Hf= 50 Hz

Q: The voltage across an inductor with inductance of 18 mH is given by t<0 (V) t≥0 v₁ (t) = {e-st (V)…

A: Given: Voltage across inductor : vLt=0 t<0e-5t V t⩾0 where L=18 mH and iL=0 for…

Q: In a RC charging circuit, given R = 150 Kohm, Supply voltage = 15 V and voltage across the capacitor…

Concept explainers

DC Generator

An electromechanical machine which converts input mechanical energy to respective output electric energy is called a generator.

Question

The Subject is Basic Electrical Engineering

Chapter 15. Conductance, Susceptance and Admittance of AC Circuit.

3. In the circuit shown in Figure, the total current is 150 mA and the current through
the inductor is 100 mA. Determine what the applied voltage is. Also, knowing that
the frequency is 50 Hz, find the value of L.
150 mA
100 mA
50 Hz
100 2

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

An AC circuit contains a 24 resistor, a 15.9-mH inductor, and a 13.3F capacitor connected in parallel. The circuit is connected to a 240-V, 400-Hz power supply. Find the following values. XL=XC=IR=AIL=AIC=AP=WVARsL=VARsC=IT=AVA=PF=%=
Assume that the voltage drop across the resistor, ER, is 78 V; the voltage drop across the capacitor, EC, is 104 V; and the circuit has a total impedance, Z, of 20 . The frequency of the AC voltage is 60 Hz. Find the missing values. ET ER78V EC104V IT IR IC Z20 R XC VA P VARSC PF C
Assume that the current flow through the resistor, IR, is 15 A; the current flow through the inductor, IL is 36 A; and the circuit has an apparent power of 10,803 VA. The frequency of the AC voltage is 60 Hz. ET ER EL IT IR15A IL36A Z R XL VA10,803 P VARSL PF L
Three capacitors having capacitance values of 20F,40F, and 50F are connected in parallel to a 60 - Hz power line. An ammeter indicates a circuit current of 8.6 amperes. How much current is flowing through the 40F capacitor?
Assume that the voltage drop across the resistor, ER, is 78 V, that the voltage drop across the inductor, EL, is 104 V, and the circuit has a total impedance, Z, of 20 . The frequency of the AC voltage is 60 Hz. ETITZ20VAPFER78VIRRPEL104VILXLVARsLL
The circuit is connected to a 60-Hz line. The apparent power in the circuit is 29.985 VA, and the power factor is 62.5%. The resistor has a voltage drop of 14.993 V, the inductor has an inductive reactance of 60 , and the capacitor has a capacitive reactance of 45 . ETITZVA29.985PF62.5%ER14.993VIRRPELILXL60VARsLLECICXC45VARsCC
You are a journeyman electrician working in an industrial plant. Your task is to connect an inductor to a 480-V, 60-Hz line. To determine the proper conductor and fuse size for this installation, you need to know the amount of current the inductor will draw from the line. The nameplate on the inductor indicates that it has an inductance of 0.1 H. An ohmmeter reveals that it has a wire resistance of 10 . How much current should this inductor draw when connected to the line?
You are an electrician working in an industrial plant. You discover that the problem with a certain machine is a defective capacitor. The capacitor is connected to a 240-volt AC circuit. The information on the capacitor reveals that it has a capacitance value of 10 mF and a voltage rating of 240 VAC. The only 10-mF AC capacitor in the storeroom is marked with a voltage rating of 350 WVDC. Can this capacitor be used to replace the defective capacitor? Explain your answer.
You are working in an industrial plant. You have been instructed to double the capacitance connected to a machine. The markings on the capacitor, however, are not visible. The capacitor is connected to 560 volts and an ammeter indicates a current of 6 amperes flowing to the capacitor. What size capacitor should be connected in parallel with the existing capacitor? What is the minimum AC voltage rating of the new capacitor? What is the minimum DC voltage rating of the new capacitor? What is the minimum KVAR size that can be used in this installation?
Fill in all the missing values. Refer to the formulas that follow. Resistance Capacitance Time constant Total time 150 k 100 F 350 k 35 s 350 pF 10 s 0.05 F 1.2 M 0.47 F 12F 0.05 s 86 k 1.5 s 120 k 470 pF 250 nF 100 ms 8 F 150 s 100 k 150 ms 33 k 4 F =RCR=CC=R Totaltime=5
A capacitor uses air as a dielectric and has a capacitance of 3 F. A dielectric material is inserted between the plates without changing the spacing, and the capacitance becomes 15 F. What is the dielectric constant of this material?
A 1-H inductor is connected in series with a 6-ohm resistor. If the connection is energized from a 9-V DC source, determine the current (in amperes) through the circuit for a long time. The initial current is 100 mA. Express your answers accurate to four decimal places. No need to put the units.