3. The smooth block B, having a mass of0.2 kg is attached to the vertex A of the right circular cone using a light cord. If the block has a speed of 0.5m/sec around the cone, determine the tension in cord and the reaction which cone exerts on the block. Neglect the size of the block. (USE 6 STEP METHODS) 200 mm 400 mm 300 mm

3. The smooth block B, having a mass of0.2 kg is attached to the vertex A of the right circular cone using a light cord. If the block has a speed of 0.5m/sec around the cone, determine the tension in cord and the reaction which cone exerts on the block. Neglect the size of the block. (USE 6 STEP METHODS) 200 mm 400 mm 300 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Help ASAP P= 541kN determine vertical reaction at A(in kN) 3 decimals
A minimum force of P = 50 lb is required to hold the cylinder from slipping against the belt and the wall. Determine the weight of the cylinder if the coefficient of friction between the belt and cylinder is μs = 0.3 andslipping does not occur at the wall.
Use Area-Moment Method in solving the problem. Consider 150 mm x 150 mm section and E = 80 GPa. A=2.8 B=24.0 C=28 Determine: Vertical Reaction at B in kN. Moment Reaction at A in kN-m.
Calculate for the Moment at A in kN-m of the frame shown in figure 1 using Portal Method. Enter absolute value and use 2 decimal places in your solution.
The three forces act on the pipe assembly. If F1 = 80N and F2= 50 N replace this force system by an equivalent resultant force and couple moment acting at O. Express the results in Cartesian vector form.
- Block B has a mass m = 10 kg and is released from rest when it is on top of the cart A, which has a mass of 3m. Determine (a) the tension in cord CD needed to hold the card from moving while B slides down A, and (b) the acceleration of A and B. The coefficient of kinetic friction between A and B is µk = 0.2 and let θ = 37º.
A 10-kg cylinder D, which is attached to a small pulley B, is placed on the cord as shown. Determine the largest angles θ so that the cord does not slip over the peg at C. The cylinder at E also has a mass of 10 kg, and the coefficient of static friction between the cord and the peg is μs = 0.1.
Use Area-Moment Method. Consider 150 mm x 150 mm section and E = 80 GPa. A=2.8 B=24.0 C=28 Determine the following: Vertical Reaction at B in kN. Moment Reaction at A in kN-m.
If a horizontal force of F = 50 N is applied perpendicular to the handle of the lever at E, determine the clamping force developed at G. The mean diameter and lead of the single square-threaded screw at C and D are 25 mm and5 mm, respectively. The coefficient of static friction is μs = 0.3.
Refer to the beam loaded as shown. (a)What is the Value of horizontal reaction at the fixed support?(b)What is the value of resulting couple at A?
Properties: • b1 = 300 mm • b2 = 180 mm • d1 = 250 mm • d2 = 350 mm • f'c = 28 MPa • fy = 414 MPa • eccentricity = 200 mm Determine the following: 1. Location of the plastic centroid measured from the y-axis in mm 2. Depth of the compression block in mm 3. Nominal Axial in kN 4. Moment Capacity in kN-m
Determine support reaction at B . Given P=100 Kn L=10 m