3. Write the information from the following weld symbol.
Q: Identify the elements applied to the following welding symbols.
A: Given: To determine: Welding symbols
Q: Symbol
A: From the given figure the given welding symbol is arrow side fillet welding.
Q: Discuss the standard location of elements of a welding symbol.
A: Welding symbol that goes on the reference line to show the shape of welds, such as plug or filler.
Q: E70XX 1/4 V2 1/4 For the welding information shown, calculate the design capacity of the weld Rweld…
A:
Q: A fillet weld can be used to join which of the following joint types: * O All of the Mentioned
A: Fillet welding is the process of welding to weld the 2 metals at an angle or perpendicularly.
Q: A fillet weld can be used to join which of the following joint types: * O All of the Mentioned O Tee…
A: Correct answer: All of the mentioned
Q: 9- Excess weld metal according to EN ISO 5817, t = 20.0 mm, measured : h = 6.7 mm b = 35.0 mm…
A: We can answer the first question since the exact one is not specified. Please resubmit the question…
Q: How pressure exerted on the weld joint depends on resistance at the point of contact At high…
A: resistance welding is the joining of metals by applying pressure and passing current for a…
Q: In addition to continuously changing the weld pattern,what other changes must be continually made…
A: Considered to be the most challenging pipe position is the 66 or 45° fixed inclined position.…
Q: .) How many different types of welds are specified on the print and what are they? (Hint: look at…
A: Welds come in a variety of shapes, which are best defined by their cross-sectional form. The fillet…
Q: 6 Compare between the weld decay Attack and Knife-Line Attack.
A: There are two major corrosions that occur in steels and they are weld decay and knife-line.
Q: Find all the information from the following weld symbol 20
A: The set of symbols which together decide the type of weld or joint that is to be made at the…
Q: Name of the welding defect shown in figure is
A: The defect is incomplete fusion Which occur due to rapid welding .
Q: Question 2. point J, what is the maximum shear stress the weld has to with- K 700 mm F=3kN Txy
A:
Q: 5 Which of the following appropriate methods are adopted for reducing distortion in weldments?
A: When materials are welded together, because of the uneven cooling the stresses are induced in the…
Q: Design the above joint using welded connection. The w=15mm. The required length of weld is:
A:
Q: Explain the meaning of each weld shown in figure below.
A: In the first figure , the joint present is lap joint. Lap joints are formed when two overlapping…
Q: Why should convex weld faces be avoided?
A: Excessive Convexity This discontinuity can produce a notch effect in the welded area and,…
Q: Determine the weld macrostructures at point X and Y as Figure 1(b).
A:
Q: Why are all welds not inspected to the same level orstandard?
A: Information Provided: Not all welds undergo the same level or standard of inspection. Not all welds…
Q: Give information about hydrogen embrittlement in the weld.
A:
Q: 1) The development of residual stresses in weld joint is due to? Heat treatment operations OUnevenly…
A: Residual stresses are the stresses that remains in the material even after the removal of the force…
Q: Sketch the groove welds specified and show all given weld dimensions
A: Sketch the groove welds The groove weld is a most common welding in which root opening is present.…
Q: Why must cast iron weld metal be ductile
A: Cast iron is the alloy of carbon and iron. Cast iron has high hardness due to presence of high…
Q: Write all details of the following welding symbol. 25
A: Symbols shown in a given question is expressed below in diagram.
Q: - What is mean by M24 X 2-RH 2-What is the function of a cover plate in riveted joints? 3- If a weld…
A: Given : M24 X 2-RH
Q: In your own words, explain the cause/s of the weld defect below and how can you prevent it from…
A:
Q: DOUBLE FILLET WELD CONCAVE FACE SIZE 20 MM
A: Double Fillet Weld A double fillet weld occurs when a fillet weld is required on both sides of the…
Q: How many categories of weld are associated with Weld symbols
A: There are so many categories of welds, these are given as with symbols, (1) Butt weld between plates…
Q: On all CJP groove welds in butt joints transverse to the computed tensile stress, they: O A. Shall…
A: Introduction The Complete Joint Penetration (CJP) groove weld is a groove weld that extends…
Q: The name of the edge preparation for welding shown in the following figure is O a. Double bevel O b.…
A: GIVEN DATA WELDING JOINT GIVEN WE HAVE TO CHOOSE CORRECT OPTION FROM GIVEN OPTION
Q: What weld section properties are required to analyze the weld between the horizontal tube and the…
A:
Q: T3.2.2 The bracket shown below supports an 18 kN load. The fillet weld extends for full 100 mm…
A:
Q: 7) On increasing the diameter of the SAW electrode, keeping the same current and arc length Width of…
A: The depth upto which the fused metal extends within the base metal or the pass from the previous…
Q: weld is called for by the small triangle on the underside of the welding symbol?
A:
Q: Give two reasons for using standard letter designations and give two methods used to specify the…
A: Reasons for using standard letter designation 1) It can be easy to understand to everybody 2) It is…
Q: 2. Find the information from the following weld symbol. 15 3. What are the types of Cycloids?
A: From the figure, we can deduce the subsequent properties of the weld; (1) The type of weld is a…
Q: Draw a welding symbol from the following information DOUBLE BEVEL BUTTWELD JOINT CONCAVE FACE SIZE…
A: Solution: The weld symbol is shown below:
Q: Q1. True and False questions 1. Efficiency of a power screw depends upon both helix angle and…
A: ● Power screw is a mechanical device for power transmission and conversion. ● Parallel filled weld…
Q: On all CJP groove welds in butt joints transverse to the computed tensile stress, they
A: A groove weld is an aperture between two joint elements that enables room for the metal to be…
Q: Draw the welding symbol from the following information. SINGLE BEVEL BUTT WELD CONCAVE FACE…
A: To Draw the welding symbol from the following information. SINGLE BEVEL BUTT WELD CONCAVE FACE…
Q: In a welding symbol for a u-groove with a consumable insert on the other side. What is the 2 in the…
A: The tail of the welding symbol is used to indicate the welding process as well as its specification…
Q: Assuming that the quired weld size for the weld shown below using E60 welding rod (S, = 345 MPa) nd…
A:
Q: What will be the notation of throat length of a fillet weld
A: Given data⇒ Fillet weld Throat length
Q: Q1/ If the weld size equal to (1.1 cm) find the Umax for figure bellow?
A: Given:-
Q: How do excessive amounts of manganese affect a weld?
A: The fabrication process is the process which is involved to build a product by mixing standardized…
Q: Q2/ The bracket shown in Figure (2) support a repeated load of 4000 N. The fillet weld extends for…
A: This question is solved with the help of safe stress expression, As we know, the safe stress…
Step by step
Solved in 3 steps with 9 images
- Q#2: Differentiate b/w the following: 1-Fillet weld & Groove weld 2-A36 & A242 structural steels3.) How many different types of welds are specified on the print and what are they? (Hint: look at the symbol on the reference line) 4.)For the weld between parts TP1 and TP2, what does the 3 mean? 5.)What standard should be used to interpret the weld symbols on this print? (Hint look at the notes given at the top of the print.) 6.) As indicated by the welding symbols, the welds to be made on ______________________?* a. the near side b. the far side c. both sides d. all around 7.)What note is found in the tail of the welding symbol? 8.)What is the name of this part? 9.)Who drew this print? 10.)What company was this print written for?Perform the welding as shown by the welding symbols.