i need the answer quickly 3.33 The following data are obtained from a tensile test of a12.7-mm-diametler aluminum specimen having a gage length óf50 mm. After the specimen ruptures, the minimum (neck) diameteris found to be 8.8 mm. Plot the engineering stress-strain diagramand determine:(a) The modulus of elasticity.(b) The proportional limit.(c) The yield strength at 0.2% offset.(d) The ultimatestrength.(e) The percent elongation in 50 mm.(f) The percent reduction in area.(g) The true ultimate stress.(h) The tangent and secant moduli at a stress level of 310 MPa.Stress, MPaStrainStress, MPaStrain350.00052840.0062700.00103050.021040.00143190.051390.00173260.081720.00243120.122070.00302910.152420.00352560.202590.0039(Fracture)

Given Specimen length = 50 mm Specimen diameter = 12.7 mm Specimen final diameter = 8.8 mm To find…

3.33 The following data are obtained from a tensile test of a 12.7-mm-diametler aluminum specimen having a gage length óf 50 mm. After the specimen ruptures, the minimum (neck) diameter is found to be 8.8 mm. Plot the engineering stress-strain diagram and determine:

3.33 The following data are obtained from a tensile test of a 12.7-mm-diametler aluminum specimen having a gage length óf 50 mm. After the specimen ruptures, the minimum (neck) diameter is found to be 8.8 mm. Plot the engineering stress-strain diagram and determine:

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A specimen of titanium alloy is tested in torsion and the shear stress–strain diagram is shown in Fig.a. Determine the shear modulus G, the proportional limit, and the ultimate shear stress. Also, determine the maximum distance d that the top of a block of this material, shown in Fig. b, could be displaced horizontally if the material behaves elastically when acted upon by a shear force V. What is the magnitude of V necessary to cause this displacement?
3.For a body under three dimensional stress state, describe the procedure for obtaining the absolute maximum shearing stress at a given point. What is meant by strain transformation? Describe two procedures for obtaining stress form Mohr’s circle for strain.
A rectangular steel block is 300mm in the x direction, 200mm in the y direction and 150mm in the z direction. The block is subjected to a triaxial loading consisting of three uniformly distributed forces as follows: 250kN tension in the x direction, 320kN compression in the y direction and 180kN tension in the z direction. For steel, v=0.30 and E=200,000MPa. Determine the total strain in the x direction due to the forces applied in the three directions.
A rectangular steel block is 3 inches long in the x direction, 2 inches long in the y direction, and 4 inches long in the z direction. The block is subjected to a triaxial loading of three uniformly distributed forces as follows: 48 kips tension in the x direction, 60 kips compression in the y direction, and 54 kips tension in the z direction. If the Poisson’ Ration is 0.30 and the modulus of elasticity is 29xksi, determine the deformations at each direction. Also, determine the single uniformly distributed load in the x direction that would produce the same deformation in the y direction as the original loading.
Use the principle of Strain energy due to direct stresses strength of materials 2
1. Sketch stress-strain curves for the following three materials (mechanically worked tungsten metal, annealed tungsten metal, and tungsten carbide) on the same plot. On each curve, label the following: ultimate compressive strength (UCS), yield stress (YS), modulus of elasticity (E), and rupture stress (RS).
In constructing a large mobile, Jude hangs an aluminum sphere of mass 6.0kg from a vertical steel wire 0.50m long and 2.5x10^−3 cm^2 in cross-sectional area. On the bottom of the sphere, he attaches a similar steel wire, from which he hangs a brass cube of mass 10.0kg. For each wire, compute: (a) The tensile strain and(b) The elongation
For a body under three dimensional stress state, describe the procedure for obtaining the absolute maximum shearing stress at a given point.
The data shown in the table below were obtained from a tensile test of high-strength steel. The test specimen had a diameter of 13mm and a gage length of 50mm. At fracture, the elongation between the gage marks was 3.0mm and the minimum diameter was 10.7mm. Plot the conventional stress-strain curve for the steel and determine the propotional limit, modulus of elasticity (i.e the slope of the initial part of the stress-strain curve), yield stress at 0.1% offset, ultimate stress, percent elongation in 50mm, and percent reduction area. TENSILE-TEST DATA Load(kN) Elongation(mm) 5 0.005 10 0.015 30 0.048 50 0.084 60 0.099 64.5 0.109 67.0 0.119 68.0 0.137 69.0 0.160 70.0 0.229 72.0 0.259 76.0 0.330 84.0 0.584 92.0 0.853 100.0 1.288 112.0 2.814 113.0 Fracture
A rectangular steel block is 3 inches long in the x direction, 2 inches long in the y direction, and 4 inches long in the z direction. The block is subjected to a triaxial loading of three uniformly distributed forces as floows; 48 kips tension in the x directio, 60 kips compression in the y direction, and 54 kips tension in the z direction. If v = 0.30 and E = 29 x 106 psi, determine the single uniformly distributed load in the x direction that would produce the same deformation in the y direction as the original loading.
Mechanics of Deformable Bodies. Eight steel cables (with equal distance to each other) are supporting a circular heavy moulding of diameter 3m from an overhead point. If the moulding weighs 5 kN/m and the attachment point is 4m above it, determine the following: a. Calculate the tension of the cable. b. Determine the diameter of the wire if the allowable stress is 125 MPa. c. If the diameter of the cable is 10 mm, find the deflection of the steel cable. d. If the diameter of the cable is 10 mm, find the vertical displacement of the molder.
a copper-rolled wire 10 m long and 1.5mm in diameter when supporting a weight of 35.7 kg, elongates 1.36 cm. Compute the stress (kg/cm^2), strain, and the value of the Young's modulus of elasticity for this wire.