3.A multiple disc clutch has three discs on the driving shaft and two on the driven shaft, providing four pairs of contact surfaces. The outer diameter of the contact surfaces is(250 mm) and the inner diameter is (150 mm). Determine the maximum axial intensity of pressure between the discs for transmitting (18.75 kW)at (500 r.p.m). Assume uniform wear and coefficient of friction as(0.3).

3.A multiple disc clutch has three discs on the driving shaft and two on the driven shaft, providing four pairs of contact surfaces. The outer diameter of the contact surfaces is(250 mm) and the inner diameter is (150 mm). Determine the maximum axial intensity of pressure between the discs for transmitting (18.75 kW)at (500 r.p.m). Assume uniform wear and coefficient of friction as(0.3).

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the maximum, minimum and average pressure in a plate clutch when the axial force is 3.3kN. The inside radius of the contact surface is 81mm and the outside radius is 110 mm. Assume uniform wear.
An engine of a motor vehicle with a wheel diameter of 712 mm develops 50 kW at 2,000 rpm combined efficiencyof the differential and transmission is 75% with an over-all speed reduction to. 1 determine he torque to bedelivered by the clutch N-m.
A single plate clutch, effective on both sides, is required to transmit 75 kW at 1000 rpm. Determine the outer radii of frictional surface when the ratio of radii is 1.75 and the maximum pressure is not to exceed 0.5 MPa. Also determine the axial thrust to be provided by springs. The mean radius of the frictional surface for uniform wear is 110 mm.
A conical clutch has an included angle of 120°, a coefficient of friction of 0.4, and outer and inner diameters of 85mm and 18mm respectively. Using both the uniform wear theory and the uniform pressure theory, calculate the force required to press the two halves together if it is to transmit 300W at 750rev/min. The uniform wear theory and the uniform pressure theory deliver different values for torque in the same system. Which theory would be preferred in practice for use in calculations involving a friction clutch? Give reasons for your choice.
A cone clutch is to transmit 10 KW at 600 r.p.m. the cone has aface angle of 10◦The width of the face is halfe of the mean radius and the max pressureis 0.1 N/mm²Assuming uniform wear and the coefficient of friction is 0.3, find theinner and outer radius and the axial force required on the clutch. Subject: Theory of Machines
A multiplate clutch has three pairs of contact surfaces. The outer and inner radii of the contact surfaces are 100 mm and 50 mm respectively. The maximum axial spring force is limited to 1 kN. If the coefficient of friction is 0.35 and assuming uniform wear, find the power transmitted by the clutch at 1500 r.p.m.
A single plate friction clutch with both sides of plate being effective is used to transmit power at an engine speed of 200rpm. It has outer and inner radii 10cm and 8cm respectively. Find maximum power transmitted and the corresponding axial thrust, if the maximum intensity of pressure is not to exceed 0.08N/mm2 . Assume coefficient of friction as 0.25.
Question No.13: A multiple disc clutch has three discs on the driving shaft and two on the driven shaft, providing four pairs of contact surfaces. The outer diameter of the contact surfaces is 250mm and inner diameter is 150mm. Determine the maximum axial intensity of pressure between the discs for transmitting 18.75kW at 500 rpm. Assume uniform wear and coefficient of friction as 0.3.
A local utility vehicle production company have considered using in one of its design a multi-disc clutch consisting of a 9 steel disc and 8-bronze discs with effective outside and inside diameter of 220mm and 160mm, respectively. If the shaft turns at 150rpm and an axial force of 600N is applied, find the horsepower capacity, considering a coefficient of friction of 0.25
Q2 ) A cone clutch is to transmit 10 KW at 600 r.p.m. the cone has aface angle of 10◦The width of the face is halfe of the mean radius and the max pressureis 0.1 N/mm²Assuming uniform wear and the coefficient of friction is 0.3, find theinner and outer radius and the axial force required on the clutch.
A single disc clutch with both sides effective is required for a vehicle. The power for initial estimation of the clutch is 100 kW at 4000 rpm. Determine the radial dimensions (inner and outer radius) and the actuating force (W). Base the design on the uniform wear assumption. Assume maximum pressure (pmax) as 1.6 MN/m2 and ?2?1= 1√2where ‘r2’ and ‘r1’ represent inner and outer radius of the friction surface. Take µ = 0.35. Find also the minimum pressure (pmin).
...A plate clutch with single driving plate with contact surfaces on each is required to transmit 35 kW at 2400 rpm. Given that μ = 0.29, R = 1.25r, Pmax = 0.2 MPa, determine the inside radius of the frictional surface in mm. Assume the uniform wear conditions.