320 mm 470 mm 42 mm 54 mm T= 2.2 kN.m Aluminium Steel Figure Q1/ Rajah S1 The solid aluminium cylinder AB and solid steel cylinder BC are bonded (welded) together at B and are attached to fixed supports at A and C as shown in Figure Q1. The assemble is subjected to torque, T= 2.2 kN.m at B. Knowing that the modulus of rigidity of aluminium and steel are 24 GPa and 80 GPa respectively, determine: (a) Is this problem statically determinate or statically indeterminate? Justify your answer. (b) The internal torque develops in the aluminium cylinder AB and steel cylinder BC. (c) The maximum shear stress for cylinder AB and BC (d) The angle of twist at B Fixed Support Fixed Support

320 mm 470 mm 42 mm 54 mm T= 2.2 kN.m Aluminium Steel Figure Q1/ Rajah S1 The solid aluminium cylinder AB and solid steel cylinder BC are bonded (welded) together at B and are attached to fixed supports at A and C as shown in Figure Q1. The assemble is subjected to torque, T= 2.2 kN.m at B. Knowing that the modulus of rigidity of aluminium and steel are 24 GPa and 80 GPa respectively, determine: (a) Is this problem statically determinate or statically indeterminate? Justify your answer. (b) The internal torque develops in the aluminium cylinder AB and steel cylinder BC. (c) The maximum shear stress for cylinder AB and BC (d) The angle of twist at B Fixed Support Fixed Support

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Why is is that when I compute for the diameter, the answer is 7.9706? How was 13.22 obtained? Bartleby link for solution: https://www.bartleby.com/questions-and-answers/a-steel-rod-is-stretched-between-two-rigid-walls-and-carries-a-tensile-load-of-5000-n-at-20c.-if-the/5c99ed3b-d083-41be-a905-b15aa3bc8648
A 10-mm diameter steel bolt is surrounded by bronze sleeve. The outer diameter of the bronze sleeve is 20 mm and its inner diameter is 10-mm. Given that the yield stress for the steel is 640 MPa and the yield stress for the bronze is 520 MPa, determine the magnitude of the maximum allowable total load that can be applied to this assembly. (Assume full bond between the steel and the bronze sleeve) Esteel = 200 GPa, Ebronze = 100 GPa, Factor of safety = 1.5
Rigid bar ABC is supported by pin-connected bar (1). Bar (1) is 2.0-in. wide, 1.00-in. thick, and made of aluminum that has anelastic modulus of E = 12,000 ksi. Determine the maximum magnitude of load P that can be applied to the rigid bar withoutcausing member (1) to buckle
THe bracket shown is made of cold drawn steel with Sy=400MPa and Su=480 MPa, and is fastened to a beam made of the same material by five rivets that are made of a steel with Sy=300 MPa and Sut=365 MPa. The thickness of the bracket and the beam are 12 mm and 16 mm respectively.Diameters of the rivets are 20 mm. What safe load F(steady) can be supported by the riveted joint for a factor of safety of 2. Use distortion energy theory of failure.
A 1∕2-in.-diameter round steel rod 40 ft long supports a loadof 4 kips. How much will it elongate? e= ΔL /L f = P/A E = (P∕A)/ (ΔL∕L) = (PL) / (A(ΔL))
A composite rod of overall length of 200 mm comprised of a steel rod and brass rod attached rigidly to the end. The diameter and the length of the steel rod are given as 10 mm and 120 mm,respectively, the diameter and the length of the brass rod as 20 mm and 80 mm respectively. The rod is used as a tie in a link mechanism and the strain in the brass rod is limited to 0,00053. Given that the total extension of the composite rod must not exceed 0,1624 mm and E for steel is 200 GPa, respectively. Determine : A) Strain in the steel rod B) Load carried by the steel and brass rods C) Modulus of elasticity for the brass
A square bar of wrought iron, 2 inches on each side, is raised to a temperature of 100 deg F above its normal. If held so that it cannot expand, K = 6.8 x 10-6 per deg F. What is the force necessary to prevent expansion? The modulus of elasticity E may be taken as 30 million psi. ( Answer : 81,600 lb)
An aluminum [E = 10,000 ksi] control rod with a circular cross section must not stretch more than 0.22 in. when the tension in the rod is 2100 lb. If the diameter of the rod is 0.372 in., determine the maximum length of the rod.
A copper bar consists from three sections: sections 1 is of 25 mm diameter and 60 mm long, section 2 is of 15 mm diameter and 50 mm long and section 3 is 20 mm square and 40 mm long. The bar is subjected to an axial tensile load which induces a stress of 20 MN/m2 on the smallest cross section. Determine the total Increase in the length of the bar when the load is applied. For copper E=100 GN/m2.
A bar ABCD consists of three sections: AB is 25 mm square and 50 mm long, BC is of 20 mm diameter and 40 mm long and CD is of 12 mm diameter and 50 mm long. Determine the stress set up in each section of the bar when it is subjected to an axial tensile load of 20 kN. What will be the total extension of the bar under this load? For the bar material, E = 210 GN/m 2. [32, 63.7, 176.8 MN/m z, 0.062 mm.] can you please answerthis question fully and if you use * can you please tell me what you mea by it?
The cylindrical bar composed of two parts (AB and BC) is fixed at ends A and C. The two parts are made of different materials with different cross-sections. An external load ? =28 kN is applied at point B. The cross-sectional area of AB and BC part is 0.9 cm2and 0.3 cm2, respectively. The modulus of elasticity of the AB and BC part is 40 GPa and 200 GPa, respectively. Determine the force reactions at ends A and C.
A steel plate subjected to a force of 3 kN and fixed to a verticalchannel by means of four identical bolts is shown in Fig. Thebolts are made of plain carbon steel 45C8 (Syt = 380 N/mm2) and thefactor of safety is 2. Determine the diameter of the shank.