Situation 1: Two wires are supporting a weight W as shown in the figure. The stresses in wire AB and ACare not to exceed 100 MPa and 150 MPa, respectively. The cross-sectional area of the two wires are 400mm2 for AB and 200 mm2 for AC.1. Which of the following most nearly gives the maximum tensile force that the wire AB can support?c. 30 kNd. 20 kNa. 50 kNb. 40 kN2. Which of the following most nearly gives the maximum tensile force that the wire AC can support?45c.30 kNa. 50 kNb. 40 kNd. 20 kN3. Which of the following most nearly gives the largest weight W that can be supported by the wires?a. 50.19 kNb. 45.68 kNc. 33.46 kNd. 41.21 kN

Answered: Image /qna-images/answer/4bb2f04b-f7c7-4bba-8ab9-88ccee000dd7.jpg

Situation 1: Two wires are supporting a weight W as shown in the figure. The stresses in wire AB and AC are not to exceed 100 MPa and 150 MPa, respectively. The cross-sectional area of the two wires are 400 mm2 for AB and 200 mm2 for AC. 1. Which of the following most nearly gives the maximum tensile force that the wire AB can support? a. 50 kN b. 40 kN 2. Which of the following most nearly gives the maximum tensile force that the wire AC can support? e. 30 kN d. 20 kN a. 50 kN b. 40 kN c.30 kN d. 20 kN 3. Which of the following most nearly gives the largest weight W that can be supported by the wires? a. 50.19 kN b. 45.68 kN e. 33.46 kN d. 41.21 kN

Situation 1: Two wires are supporting a weight W as shown in the figure. The stresses in wire AB and AC are not to exceed 100 MPa and 150 MPa, respectively. The cross-sectional area of the two wires are 400 mm2 for AB and 200 mm2 for AC. 1. Which of the following most nearly gives the maximum tensile force that the wire AB can support? a. 50 kN b. 40 kN 2. Which of the following most nearly gives the maximum tensile force that the wire AC can support? e. 30 kN d. 20 kN a. 50 kN b. 40 kN c.30 kN d. 20 kN 3. Which of the following most nearly gives the largest weight W that can be supported by the wires? a. 50.19 kN b. 45.68 kN e. 33.46 kN d. 41.21 kN

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Calculate the largest weight W that can be supported by two wires. The stress in either wire is not to exceed 7.6 MPa. The cross-sectional areas of wires AB and AC are 150 mm2 and 250 mm2, respectively.Answer: W = ___________________
Determine the largest weight W in N that can be supported by two wires shown in the figure.The stress in either wire is not to exceed 261 Mpa. The cross-sectional areas of wires AB and ACare 258 mm^2 and 320mm^2 respectively.
As shown in the figure, three wires with different areas and modulus of elasticity are used to lift a load W. Their unstressed lengths are L1, L2, and L3. (a) What stress exists in the longest wire, and (b) shortest wire? (c) Determine the stress in the shortest wire if W = 500 Ib. (d) What should be the load so that the two wires will stretch to the length of the longest wire?
A load of P = 4900 N is acting on member AC. The length of AC is d = 300 mm. The cross-sectional area of AB is 375 mm2 while the cross-sectional area of C is 575 mm2 . Determine the magnitude (in N) of the force acting on rod AB if the compressive stress in the smooth support C is equal to the tensile stress in the rod AB. Round off the final answer to two decimal places.
The 981-kg uniform bar AB is suspended from two cables AC and BD each with cross-sectional area 339 mm2. Find the location x (in mm) of P that can be safely applied to the bar if the stresses in AC and BD are limited to 119 MPa and 52 MPa, respectively. Express your answer in two decimal places.
As shown, three steel wires, each 28 mm2 in area, are used to lift a mass M. Their unstretched lengths are 19.99 m, 19.98 m, and 20 m. If M= 1,182 kg. what stress exists in the MIDDLE wire? Use E=215 Gpa. Answer must be in MPa.
A homogeneous 2700 kg bar AB is supported at either end by a cable as shown in the figure. Determine the stress in the steel cable if the cross sectional area of the bronze and steel cables are 55 mm^2 and 35 mm^2, respectively.
A rectangular steel block is 3 inches long in the x direction, 2 inches long in the y direction, and 4 inches long in the z direction. The block is subjected to a triaxial loading of three uniformly distributed forces as floows; 48 kips tension in the x directio, 60 kips compression in the y direction, and 54 kips tension in the z direction. If v = 0.30 and E = 29 x 106 psi, determine the single uniformly distributed load in the x direction that would produce the same deformation in the y direction as the original loading.
A steel rod is 0.02-m in diameter and 2.5-m in length. The modulus of elasticity ofthis material is 210 GPa. The change in length afterapplying a tensile force of 150 kN is?
1-A bar of square cross section is subjected to point loads of P1, P2, P3 and P4 as shown here. Find the magnitude of the force P3 necessary for the equilibrium, if P1= 110 kN, P2 = 210 kN & P4 = 190 kN. Also, determine the stresses in each section & the net change in the length of steel bar. square of size a1=50mm, L1=30 cm, size a2 = 40mm, L2=39 cm, size a3=50 mm & L3 =32 cm Take E = 166 GPa. The force P3 to make it to equilibrium in kN is The Stress in section 1 in N/mm2 is The Compressive Stress in section 2 in N/mm2 is The stress in section 3 in N/mm2 is The total change in length in x10-3 mm is
The BC and DE bars in the figure are made of steel (Eç = 200GPA), each of which has a width of 12 mm and a thickness of 6 mm. According to this; a-) When a force of P = 2.4 kN is applied to the rigid element AF, the tails formed in BC and DE bars,
A-36 Aluminium rod shown in figure Q1a is 2.5 m long and must not stretch more than 1.5 mm when an 10.5 kN load is applied to it. Knowing that E = 75 GPa, determine (i) the smallest diameter rod which should be used, (ii) the corresponding normal stress caused by the load.