340 MPa 65 MPa - 55 MPa

Q: If the applied torque on shaft CD is 82.5 N-m, determine the absolute maximum shear stress in shaft…

A: GIVEN DATA - A GEAT TRAIN GIVEN  WE HAVE TO FIND SHEAR STRESS ON SHAFT CD

Q: 4. A cylinder with inner radius a and outer radius 2a is subjected to internal pressure p,. Using a…

A:

Q: The plate is made of Tobin bronze, which yields at sY = 25 ksi. Using the maximum distortion energy…

A: Given data as per question

Q: A loading condition is shown below. The wires at point A and D both made from a steel with the yield…

A: Drawing the free body diagram of the given question:-

Q: The steel shaft has a radius of r=50 mm. Determine the torque (T) applied to the shaft if the two…

A: Given Data Radius of the steel shaft is : r=50 mm εx'=-80×10-6 εy'=80×10-6 Young's modulus of steel…

Q: The gas tank is made from A-36 steel (Oyield= 300 MPa) and has an inner diameter of 1.5 m and a wall…

A:

Q: Determine the state of stress at point A on the cross section of the shaft at section a–a. Show the…

A: The free-body diagram of point A is written as, On using the force equilibrium in the z-direction,…

Q: If the material is machine steel having a yield stress of sY = 700 MPa, determine the factor of…

A: To understand that there is no shear stress acting on the body. Its pure case of normal stress so…

Q: If the A-36 steel pipe has an outer and inner diameter of 20 mm and 10 mm, respectively, determine…

A: The maximum distortion energy theory is also named as von mises theory In this theory failure occurs…

Q: A cylinder having the dimensions shown is made from magnesium Am 1004-T61. If it is struck by a…

A: The given problem is solved using formulae for Strain Energy due to axial loading. All the units…

Q: Q#3: The cylindrical pressure vessel with hemispherical end-caps is made of steel. The vessel has a…

A: Given: Length of the vessel (L)=0.666×993=661.338mmOuter diameter of the vessel…

Q: Q1- Prove that the shear stress of circular shaft under pure torsion is Tr Tmax Ip Ex

A:

Q: The A-36 steel tubular shaft is 2 m long and has an outer diameter of 50 mm. When it is rotating at…

A: Given data as per question Length of tubular shaft = 2 m Outer diameter = 50 mm Power transmission =…

Q: Determine the normal stress and shear stress acting on the inclined plane AB. Solve the problem…

A: Given data: Normal stress in y direction, σy = - 15 ksi Normal stress in x direction, σx = 0 Shear…

Q: The solid shaft is made of elastic perfectly plastic material. Determine the torque T needed to form…

A: Write the expression of the torque. Write the expression of the angle of twist.

Q: The gas tank is made from A-36 steel (oyield= 300 MPa) and has an inner diameter of 1 m and a wall…

A:

Q: The 304-stainless-steel cylinder has an inner diameter of 4 in. and a wall thickness of 0.1 in. O…

A:

Q: The solid aluminum shaft has a diameter of 50 mm and allowable shear stress of tallow = 60 MPa.…

A:

Q: If a critical point at structural element is subjected to the stress shown on the 2D element,…

A: Maximum principal stress theory :- Failure occur when maximum principal stress on body exceeds the…

Q: A cylinder having the dimensions shown is made from magnesium Am 1004-T61. If it is struck by a…

A: Given Weight of the block=W=800lb Mass =M=W/g Where g=gravitational force=32.2ft/s2 M=800/22.2=36.03…

Q: If a shaft is made of a material for which sY = 75 ksi, determine the maximum torsional shear stress…

A: Given: The yield stress of the material is sY=75 ksi.

Q: The assembly is subjected to a torque of (a) T = 90 Nm (b) T = 200 Nm. If the Factor of safety for…

A:

Q: 350 MPa. Using the distortion-energy and maximum-shear-stress theorie determine the factors of…

A: Given: To determine: FOS according to maximum shear stress and distortion energy theory

Q: The bar has a diameter of 40 mm. Determine the state of stress at point A and show the results on a…

A: Section properties can be determined as

Q: If sY = 50 ksi, determine the factor of safety for this loading against yielding based on (a) the…

A: Given data Yield strength of the material, Sy = 50 ksi. (a) From maximum shear stress theory,…

Q: Q1- Prove that the shear stress of circular shaft under pure torsion is Tr %3D Tmax Ip

A: Given Circular shaft To find ζmaax=TrIP

Q: A thick-walled cylindrical pressure vessel with an inside diameter of 280 mm and an outside dianeter…

A:

Q: a critical point at structural element is subjected to the stress shown on the 2D element, determine…

A:

Q: The 2-m-long tube is made of an elastic perfectly plastic material as shown. Determine the applied…

A:

Q: If a machine part is made of titanium (Ti-6A1-4V) and a critical point in the material is subjected…

A: Given Data: The principal stress is σ1. The principal stress is σ2=0.5σ1. The yield stress…

Q: The copper pipe [G = 7,000 ksi] has an outside diameter of 3.000 in. and a wall thickness of 0.125…

A: For solution refer below images.

Q: The shaft is made of A992 steel and has an allowable shear stress of 95 MPa. When the shaft is…

A:

Q: 4. A cylinder with inner radius a and outer radius 2a is subjected to internal pressure p. Using a…

A: Stress is a measurement of how the material reacts to external influences. It's just the external…

Q: A loading condition is shown below. The wires AB and CD both have yield strength (Sy) of 71 ksi,…

A: Draw the free-body diagram of the system.

Q: The five-bolt connection must support an applied load of P = 1800 lb. If the average shear stress in…

A: Solution:     dmin = 0.0987 in

Q: The copper pipe [G = 6,000 ksi] has an outside diameter of 3.375 in. and a wall thickness of 0.250…

A: Given:G=6,000 ksid=3.375 int=0.250 int=85 lb-ft/fta=2.5 ftb=3.5 ftc=7.0 ft

Q: The 304-stainless-steel cylinder has an inner diameter of 4 in. and a wall thickness of 0.1 in. If…

A:

Q: If the journal bearings at A and B exert only horizontal and vertical forces on the shaft, determine…

A:

Q: The solid steel bar shaft DF has a diameter of 50 mm and is supported by smooth bearing bearings at…

A:

Q: RI0-9. The 0-mm-diameter shaft rotates at 300 rev/min. This motion is caused by the unequal belt…

A: Write the magnitudes of unequal tensions,   T1=800 NT2=450 N   Write the expression of net torque on…

Q: If a critical point at structural element is subjected to the stress shown on the 2D element,…

A:

Q: The solid steel bar shaft DF has a diameter of 50 mm and is supported by smooth bearing bearings at…

A:

Q: If the material is machine steel having a yield stress of sY = 750 MPa, determine the factor of…

A: Given: yield stress is τys=750 MPa from the figure given we observe that σx=-500MPa and σy=200MPa…

Q: Two vertical steel wires each 0.05 in. diameter and 48in. long support a light rod over a span of 12…

A: Given Data The diameter of the vertical steel wire is: 0.05 in The length of the vertical steel wire…

Q: The 304-stainless-steel cylinder has an inner diameter of 4 in. and a wall thickness of 0.1 in. If…

A: Check this question is thin vessel or not r/t=2/0.1=20>10 it is thin cylindrical pressure vessel…

Q: The drill is jammed in the wall and is subjected to the torque and force shown. Determine the state…

A: The free body diagram of the system is as follows.

Q: If the material is machine steel having a yield stress of sY = 750 MPa, determine the factor of…

A:

Q: element is subjected to the stress shown on the 2D elemen according to the maximum energy of…

A:

Q: The drill is jammed in the wall and is subjected to the torque and force shown. Determine the state…

A: A drilling machine is used to drill in-wall or furniture. To analyze the drill bit stresses we first…