36 mm 30 mm T = 500 N•m B 900 mm 600 mm

Q: 60 N- m PROBLEM 3.12 Knowing that an 8-mm-diameter hole has been drilled through each of the shafts…

A: Diameter of hole = 8 mm Determine the shaft in which maximum shearing stress occur and magnitude of…

Q: a) Determine the torque that can be applied to a solid shaft of 80-mm diameter without exceeding an…

A: Given data,  a  solid shaft d=80mm                            z=120 MPa.        So, τ=Polar…

Q: Two solid steel shafts are connected by the gears shown. Knowing that for each shaft G= 11.2 * 106…

A: Given Data: The modulus of rigidity of the shaft is: G = 11.2 X 106 The allowable shear stress is:…

Q: Knowing that a given vertical shear V causes a maximum shearing stress of 50 MPa in a thin-walled…

A: Write the expression of the first moment of inertia for point A. Write the expression of the first…

Q: Shaft CD is made from a 66-mm-diameter rod and is connected to the 48-mm-diameter shaft AB as shown.…

A:

Q: 60 N. m 1) Knowing that each portion of the shafts AB, BC, and 144 N m CD consist of a solid…

A: Given: Torque at position A is TA=48 N·m. Torque at position B is TB=144 N·m. Torque at position C…

Q: PROBLEM 3.56 Two solid steel shafts are fitted with flanges that are then connected by bolts as…

A:

Q: Under normal operating conditions, the electric motor exerts a 12-kip·in. torque at E. Knowing that…

A: Understand that the net torque on a cross-section is calculated by the sum of torques on any one…

Q: The torques shown are exerted on pulleys A and B. Consider TA = 270 N·m and TB = 400 N·m. Knowing…

A:

Q: The solid shaft shown is formed of a brass for which the allowable shearing stress is 55 MPa.…

A:

Q: PROBLEM 3.56 Two solid steel shafts are fitted with flanges that are then connected by bolts as…

A:

Q: A torque of magnitude T 1000 N'm is applied at D as shown below. Knowing that the allowable shearing…

A:

Q: 22 mm For the cylindrical shaft shown, determine the maximum shearing stress caused by a torque of…

A:

Q: (a) Determine the maximum shearing stress caused by a 4.6-kN • m torque T in the 76-mm-diameter…

A: Given dataApplied Torque(τ)=4.6kN.mDiameter of shaft(D)=76 mm=76*10-3mDetermine:-a)Maximum shear…

Q: The preliminary design of a motor-to-generator connection calls for the use of a large hollow shaft…

A: Given Data: The inner diameter of the shaft is d = 4 in. The outer diameter of the shaft is D = 6…

Q: A torque T5 3 kN·m is applied to the solid bronze cylinder shown. Determine (a) the maximum shearing…

A: Given data :T=3 KN.mL=200 mma) Max. shear stress will occur on surface of shaft .    ζmax=T205…

Q: The design specifications of a 1.2-m-long solid transmission shaft require that the angle of twist…

A: Given Data: The length of the shaft is L = 1.2 m. The allowable angle of twist is θ = 4◦. The…

Q: (a) Determine the torque that can be applied to a solid shaft of 40-mm diameter without exceeding an…

A: Let ds =Diameter of solid shaft =40mm As = Area of solid shaft =1256.63mm2 τ =Allowable shear stress…

Q: The steel jacket CD has been attached to the 40-mm-diameter steel shaft AE by means of rigid flanges…

A: Given Data: The outer diameter of the jacket is D = 80 mm. The thickness of the jacket is t = 4 mm.…

Q: Determine the range of values of σx for which the maximum in-plane shearing stress is equal to or…

A: Step-1 Given: The normal stress on the vertical plane is σX. The normal stress on the horizontal…

Q: Two solid shafts are connected by gears as shown and are made of a steel for which the allowable…

A: Given, dBC= 1.6 in dEF= 1.25 in

Q: Under normal operating conditions, the electric motor exerts a 12-kip·in. torque at E. Knowing that…

A:

Q: Under normal operating conditions, the electric motor exerts a torque of 2.4 kN·m on shaft AB.…

A: Given data :TAB = 2.4 kN.m = 2.4 x 106N.mmTAB = (?)  , TBC = (?)  , TCD = (?)

Q: Shaft AB is made of a steel with an allowable shearing stress of 90 MPa and shaft BC is made of an…

A: Given that ;          Allowable shearing stress of steel τAB =90MPa…

Q: 5) Knowing that an 8-mm-diameter hole has been drilled through each of the shafts AB, BC, and CD,…

A: The stress which is induced in a shaft due to torque or twisting moment parallel to the…

Q: cylinders shown.  a) For the 3-in. diameter solid cylinder and loading shown, determine the maximum…

A:

Q: Two solid steel shafts are fitted with flanges that are then connected by bolts as shown. The bolts…

A: Torque T = 500 N·m            G = 77.2 GPa From diagram            TA+TB=TTA+TB=500 ×103…

Q: 2. Shaft BC is hollow with inner and outer diameters of 90 mm and 120 mm, respectively. Shafts AB…

A: 1. Problem statement: To find the minimum and maximum shearing strength in the shaft BC and…

Q: Two solid steel shafts are fitted with flanges that are then connected by bolts as shown. The bolts…

A: T=TAB,LAB=0.6mmc=12d=302=15mmJAB=π2c4=79,481.25mm4φB=TABLABG.JABTAB=G.JABφBLAB=77×109×79481.250.6φB…

Q: A 1.5-m-long solid steel shaft of 48-mm diameter is to transmit 36 kW between a motor and a machine…

A:

Q: A torque T = 1500 N − m is applied to the hollow shaft shown that has a uniform 10 mm wall…

A: find the shear stress at a and b and angle of twist.

Q: The solid rod AB has a diameter dAB = 60 mm. The pipe CD has an outer diameter of 90 mm and a wall…

A:

Q: Ql: (a) Determine the torque that can be applied to a solid shaft of 40-mm diameter without…

A: Given Data : Solid shaft Diameter of shaft(d)=40 mm=0.040 m Allowable shearing stress is

Q: The solid spindle AB is made of a steel with an allowable shearing stress of 12 ksi, and sleeve CD…

A: Given data as per question Shear stress in solid spindle =12 ksiShearing stress of sleeve=5.8…

Q: The solid shaft shown is formed of a brass for which the allowable shearing stress is 55 MPa.…

A:

Q: Shaft BC is hollow with inner and outer diameters of 90 mm and 120 mm, respectively. Shafts AB and…

A: Find, 1-Maximum shear stress and minimum shear stresse in BC shaft  2- diameter of AB or CD

Q: Two solid steel shafts are fitted with flanges which are then connected by fitted bolts so that…

A:

Q: For the gear train shown, the diameters of the three solid shafts are: dAB = 20 mm, dco = 25 mm, dgf…

A:

Q: The design specifications of a 2-m-long solid circular transmission shaft require that the angle of…

A: Given, Length of the shaft (L) = 2 m The angle of twist (θ) = 3° = 0.052 radians Torque (T) = 9 kN.m…

Q: Please answer the following

A: Given data DAB=30 mmDBC=46 mmdAB=10 mmdBC=25 mmTAB=10 N·mTBC=20 N·m

Q: 3.7 The torques shown are exerted on pulleys A, B, and C. Knowing that both shafts are solid,…

A: Consider shaft AB Let TAB be the torque in the shaft AB if a section is passed through shaft AB…

Q: A torque of magnitude T = 900 N.m is applied at D as shown. Knowing that the diameter of shaft AB is…

A:

Q: Knowing that the internal diameter of the hollow shaft shown is d = 0.9 in., determine the maximum…

A: Given data  outer dia of hollow shaft (do) = 1.6 in. inner dia of hollow shaft (di) = 0.9 in. torque…

Q: The two solid shafts and gears shown are used to transmit 12 kW from the motor at A operating at a…

A:

Q: a) Determine the torque that can be applied to a solid shaft of 20-mm diameter without exceeding an…

A: Torque for solid shaft can be determined as

Q: The torques shown are exerted on pulleys A, B, and C. Knowing that both shafts are solid, determine…

A: Torque acting in the shaft AB by taking moment about x axis is TAB=3.6 kip·in Torque acting in the…

Q: 3.27 A torque of magnitude T = 100 N• m is applied to shaft AB of the gear train shown. Knowing that…

A:

Q: Three 18-mm-diameter steel bolts are to be used to attach the steel plate shown to a wooden beam.…

A: Find the factor of safety . Find allowable shear stress and find factor of safety by dividing…

Q: Problem 2 Shaft AB is made of a steel with an allowable shearing stress of 90 MPa and shaft BC is…

A: Given, τAB=90 MPa=90×106 MPaτBC=60 MPa=60×106 MPa dBC=50 mm=0.05 m

Q: Knowing that the internal diameter = 12mm and the torque magnitude = 1.35kn.m. Determine the maximum…

A: