Shaft AB is made of a steel with an allowable shearing stress of 90 MPa and shaft BC is made of an aluminum with allowable shearing stress of 60 MPa. Knowing that the diameter of shaft BC is 50 mm and neglecting the effect of stress concentrations, determine (a) the largest torque T that can be applied at A if the allowable stress is not to exceeded in the shaft BC, (b) the corresponding required diameter of shaft AB. Aluminum Steel C T B A

Shaft AB is made of a steel with an allowable shearing stress of 90 MPa and shaft BC is made of an aluminum with allowable shearing stress of 60 MPa. Knowing that the diameter of shaft BC is 50 mm and neglecting the effect of stress concentrations, determine (a) the largest torque T that can be applied at A if the allowable stress is not to exceeded in the shaft BC, (b) the corresponding required diameter of shaft AB. Aluminum Steel C T B A

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The preliminary design of a motor-to-generator connection calls for the use of a large hollow shaft with inner and outer diameters of 4 in. and 6 in., respectively. Knowing that the allowable shearing stress is 12 ksi, determine the maximum torque that can be transmitted by (a) the shaft as designed, (b) a solid shaft of the same weight, and (c) a hollow shaft of the same weight and an 8-in. outer diameter.
A hollow steel drive shaft (G = 11.2 × 106 psi) is 8 ft long and its outer and inner diameters are respectively equal to 2.50 in. and 1.25 in. Know that the shaft transmits 200 hp while rotating at 1570 rpm.Determine the maximum shearing stress (Ksi)
Under normal operating conditions, a motor exerts a torque of magnitude TF at F. The shafts are made of a steel for which the allowable shearing stress is 12 ksi and have diameters dCDE = 0.900 in. and dFGH = 0.800 in. Knowing that rD = 6.5 in. and rG = 4.4 in., determine the largest allowable value of TF.
The design specifications of a 2-m-long solid circular transmission shaft require that the angle of twist of the shaft not exceed 3° when a torque of 9 kN·m is applied. Determine the required diameter of the shaft, knowing that the shaft is made of (a) a steel with an allowable shearing stress of 90 MPa and a modulus of rigidity of 77 GPa, (b) a bronze with an allowable shearing stress of 35 MPa and a modulus of rigidity of 42 GPa
Knowing that the internal diameter of the hollow shaft shown is d = 0.9 in., determine the maximum shearing stress caused by a torque of magnitude T = 9 kip·in.
A steel shaft must transmit 150 kW at a speed of 360 rpm. Knowing that G = 77.2 GPa, design a solid shaft so that the maximum shearing stress will not exceed 50 MPa and the angle of twist in a 2.8-m length must not exceed 3°. Consider the frequency f to be 6 Hz. The diameter of the solid shaft is -- mm
A torque of magnitude T= 100 N·m is applied to shaft AB of the gear train shown. Knowing that the diameters of the three solid shafts are, respectively, dAB= 21 mm, dCD= 30 mm, and dEF= 40 mm, determine the maximum shearing stress in (a) shaft AB, (b) shaft CD, (c) shaft EF.
Two solid steel shafts are connected by the gears shown. Knowing that for each shaft G= 11.2 * 106 psi and the allowable shearing stress is 8 ksi, determine (a) the largest torque T0 that may be applied to end A of shaft AB and (b) the corresponding angle through which end A of shaft AB rotates.
1. A steel shaft is to be manufactured either as a solid circular or as circular tube. The shaft is required to transmit a torque of 1200 Nm without exceeding an allowable shear stress of 40 MPa, nor an allowable rate of twist of 0.75º/m. For G = 78GPa, determine: a. The required diameter do of the solid shaft.b. The required outer diameter d2 of the hollow shaft if the thickness t of the shaft is specified as one-tenth of the outer diameter.c. The ratio of diameters (that is, the ratio d2/do and the ratio of the weights of the hollow and solid shafts.
The solid shaft shown is formed of a brass for which the allowable shearing stress is 55 MPa. Neglecting the effect of stress concentrations, determine the smallest diameters dAB and dBC for which the allowable shearing stress is not exceeded. Take TC = 300 N·m.
Shaft AB is made of a steel with an allowable shearing stress of 90 MPa andshaft BC is made of an aluminum with allowable shearing stress of 60 MPa.Knowing that the diameter of shaft BC is 50 mm and neglecting the effect ofstress concentrations, determine (a) the largest torque T that can be appliedat A if the allowable stress is not to exceeded in the shaft BC, (b) thecorresponding required diameter of shaft AB.
Three shafts and four gears are used to form a gear train that will transmit 6.7 kW from the motor at A to a machine tool at F. (Bearings for the shafts are omitted in the sketch.) Knowing that the frequency of the motor is 30 Hz and that the allowable stress for each shaft is 60 MPa, determine the required diameter of each shaft. The required diameter of shaft AB is mm. The required diameter of shaft CD is mm. The required diameter of shaft EF is mm.