36. Figure P3-36 shows a beam made from 4 in schedule 40 steel pipe. Compute the deflection at points A and B for two cases: (a) the simple cantilever and (b) the supported cantilever. -6 ft- A 4 ft 8 ft- 800 lb B (a) Simple cantilever FIGURE P3-36 (Problem 36) A 800 lb B -10 ft- Support (b) Supported cantilever

36. Figure P3-36 shows a beam made from 4 in schedule 40 steel pipe. Compute the deflection at points A and B for two cases: (a) the simple cantilever and (b) the supported cantilever. -6 ft- A 4 ft 8 ft- 800 lb B (a) Simple cantilever FIGURE P3-36 (Problem 36) A 800 lb B -10 ft- Support (b) Supported cantilever

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter10: Statically Indeterminate Beams

Section: Chapter Questions

Problem 10.4.4P: -4-4 A cantilever beam is supported at B by cable BC. The beam carries a uniform load q = 200 N/M....

See similar textbooks

Similar questions

A seesaw weighing 3 lb/ft of length is occupied by two children, each weighing 90 lb (see figure). The center of gravity of each child is 8 ft from the fulcrum. The board is 19 ft long, 8 in. wide, and 1.5 in. thick. What is the maximum bending stress in the board?
B cams AB and CDE are connected using rigid link DB with hinges (or moment releases) at ends D and B (see figure a). Beam AB is fixed at joint A and beam CDE is pin-supported at joint E. Load P = 150 lb is applied at C\ Calculate the deflections of joints B and joint C Assume L = 9 ft and EI = 127,000 kip-in2. Repeat part (a) if rigid link DB is replaced by a linear spring with k = 20 kips/in (see figure b).
Solve Problem 11.3-3 for a W 10 × 45 steel column having a length L = 28 ft.
Compare the angle of twist 1 for a thin-walled circular tube (see figure) calculated from the approximate theory for thin-walled bars with the angle of twist 2 calculated from the exact theory of torsion for circular bars, Express the ratio 12terms of the non-dimensional ratio ß = r/t. Calculate the ratio of angles of twist for ß = 5, 10, and 20. What conclusion about the accuracy of the approximate theory do you draw from these results?
A foot bridge on a hiking trail is constructed using two timber logs each having a diameter d = 0.5 m (see figure a). The bridge is simply supported and has a length L = 4 m. The top of each log is trimmed to form the walking surface (see Fig, b)LA simplified model of the bridge is shown in Fig. g. Each log must carry its own weight w = 1.2 kN/m and the weight (P = 850 N) of a person at mid-span, (see Fig. b). Determine the maximum tensile and compressive stresses in the beam (Fig, b) due to bending. If load h is unchanged, find the maximum permissible value of load ... if the allowable normal stress in tension and compression is 2.5 M Pa.
Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.
Repeat Problem 10.3-15 using L = 3.5 m, max = 3 mm, and EI = 800 kN·m2.
Continuous cable ADB runs over a small friction less pulley at D to support beam OABC, which is pan of an entrance canopy for a building (see figure). A downward distributed load with peak intensity q0= 5 kNVm al O acts on the beam (see figure). Assume that canopy weight W = S kN and that the cable cross-sectional area is 100 mm". What is the required diameter of pins A, B. and D if the pins are in double shear and the allowable shear stress is SO MPa? Note that dimensions OA = AB = BC = 1.5 m.
Continuous cable A DB runs over a small friction less pulley al D to support beam OABC, which is part of an entrance canopy for a building (see figure}. The canopy segment has a weight W = 1700 lb that acts as a concentrated load in the middle of segment AB. (a) What is the maximum permissible value of load P at C if the allowable force in the cable is 4200 lb? (b) If P = 2300 lb, what is the required diameter of pins A, B, and D? Assume that the pins are in double shear and the allowable shear stress in the pins is 10 ksi.
A large precast concrete panel for a warehouse is raised using two sets of cables at two lift lines, as shown in the figure part a. Cable 1 has a length L1 = 22 Ft, cable 2 has a length L2= 10 ft, and the distance along the panel between lift points Band D is d = 14 ft (see figure part b). The total weight of the panel is W = 85 kips. Assuming the cable lift Forces F at each lift line are about equal, use the simplified model of one half of the panel in figure part b to perform your analysis for the lift position shown. Find the required cross-sectional area AC of the cable if its breaking stress is 91 ksi and a factor of safety of 4 with respect to failure is desired.
A safety valve on the top of a tank containing steam under pressure p has a discharge hole of diameter d(see figure). The valve is designed to release the steam when the pressure reaches the value Pmax If the natural length of the spring, is L and its stiffness is k, what should be the dimension ft of the valve? (Express your result as a formula for h.)
A square wood platform is 8 ft × 8 ft in area and rests on masonry walls (see figure). The deck of the platform is constructed of 2-in. nominal thickness tongue-and-groove planks (actual thickness 1.5 in.; sec Appendix CL) supported on two S-ft long beams. The beams have 4 in. × (i in. nominal dimensions (actual dimensions 3.5 in. × 5.5 in.). The planks arc designed to support a uniformly distributed load n ( lb/ft" i acting over the entire top surface of the platform. I be allowable bending stress for the planks is 2400 psi and the allowable shear stress is 100 psi. W ben analyzing the planks, disregard their weights and assume that their reactions are uniformly distributed over the top surfaces of the supporting beams. (a) Determine the allowable platform load Mr. (lb/ft2) based upon the bending stress in the planks. (b) Determine the allowable platform load if-. (lb/ft-) based upon the shear stress in the planks. (c) Which of the preceding values becomes the allowable load alolow on the platform? Hints: Use care in constructing the loading diagram for the planks, noting especially that the reactions are distributed loads instead of concentrated loads. Also, note that the maximum shear forces occur at the inside faces of the supporting beams.