4-14. The connected bar BC is used to increase the leverarm of the crescent wrench as shown. If a clockwise momentof MA120 N.•m is needed to tighten the nut at A and the%3Dextension d = 300 mm, determine the required force F inorder to develop this moment.%3Dd1530300 mmAProbs. 4-13/14

Answered: Image /qna-images/answer/62c6913d-7c2c-4ce1-84fe-316837f1a68b.jpg

4-14. The connected bar BC is used to increase the lever arm of the crescent wrench as shown. If a clockwise moment of MA extension d = 300 mm, determine the required force F in order to develop this moment. 120 N.m is needed to tighten the nut at A and the %3D d 30 300 mm A Probs. 4-13/14

4-14. The connected bar BC is used to increase the lever arm of the crescent wrench as shown. If a clockwise moment of MA extension d = 300 mm, determine the required force F in order to develop this moment. 120 N.m is needed to tighten the nut at A and the %3D d 30 300 mm A Probs. 4-13/14

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: 4-155. Replace the distributed loading by an equivalent resultant force and specify where its line…

Q: 4-126. Replace the loading on the frame by a resultant force. Specify where its line of action inter…

A: Given data as per question vertical force applied in section BD =300 N…

Q: P4-3. write the moment equations about the 1, y, and z axes. S00 N - m 1.5m C,

A: Given Data: The force acting a point A along x-axis = AX The force acting at point A along z-axis =…

Q: 4-35. Determine the smallest force F that must be applied along the rope in order to cause the…

Q: 4-14. Serious neck injuries can occur when a football player is struck in the face guard of his…

Q: *3-104. The building slab is subjected to four parallel column loadings. Determine the equivalent…

Q: 4-101. Replace the force system acting on the post by a resultant force and couple moment at point…

A: Given data: F1=300 lbF2=150 lbF3=200 lb Need to determine the magnitude of the resultant force and…

Q: *4-60. Determine the magnitude of the moment produced by the force of F = 200N about the hinged axis…

A: Given that magnitude of the force F = 200 N It is required to determine the magnitude of moment…

Q: 3-105. The building slab is subjected to four parallel column loadings. Determine F, and F, if the…

Q: 4-135. The building slab is subjected to four parallel column loadings. Determine F, and F, if the…

A: Given data , Four forces are at location(units are meter) F1=(22,0) 12 kN=(6,8) 6kN=(26,20) F2=…

Q: 4-133. If the resultant force is required to act at the center of the slab, determine the magnitude…

Q: *4-4. The A-36 steel rod is subjected to the loading shown. If the cross-sectional area of the rod…

Q: F4-39 Determine the resultant force and specify where it acts on the beam measured from A. 6KNim…

Q: 4-59. The friction at sleeve A can provide a maximum resisting moment of 125 N m about the x axis…

A: Given Data M=125 N.m

Q: 4-38. The shaft is supported by three smooth journal bearings at A, B, and C. Determine the…

A: Draw the rough sketch of the Free Body Diagram for the above system of forces.

Q: *3-44. The friction at sleeve A can provide a maximum resisting moment of 125 N• m about the x axis.…

A: The position vector of AB is written as, The force vector is written as,

Q: 4-71. Determine the required magnitude of force P. resultant couple moment on the beam is to be zero…

A: This question is based on the condition of equilibrium. The summaton of moment about at any point is…

Q: R4-5. Determine the x, y, z components of reaction at the fixed wall A. The 150-N force is parallel…

A: Given Applied force 150 N parallel to Z axis Applied force 200 N parallel to Y axis To find X, Y, Z…

Q: 4-27. The connected bar BC is used to increase the lever arm of the crescent wrench as shown. If the…

A: We are suppose to solve only one question. Please post other question as a separate question.

Q: 4-27. Determine the components of reaction at the fixed support A. The 400 N, 500 N, and 600 N…

A: Given Data: The force parallel to x-axis is Fx = 400 N. The force parallel to y-axis is Fy = 500 N.…

Q: *4-20. The tongs are used to grip the ends of the drilling pipe P. If a torque (moment) of Mp = 800…

Q: 4-58. The board is used to hold the end of a four-way lug wrench in the position shown when the man…

Q: 4-126. Replace the loading on the frame by a sng resultant force. Specify where its line of action…

A: Given data as per question The vertical force applied on BD =300 N…

Q: 4-53. The automobile has a mass of 2 Mg and center of mass at G. Determine the towing force F…

Q: 4-34. If the cable can be subjected to a maximum tension of 1.5 kN, determine the maximum force F…

A: → Consider the free body diagarm of the given figure,

Q: 3-109. Replace the distributed loading by an equivalent resultant force, and specify its location on…

A: Calculate the reaction at A, On taking moment about B,

Q: *4-36. The bar AB is supported by two smooth collars. At A the connection is a ball-and-socket joint…

A: Given:- According to the statementAt point A; ball and socket jointA→=Axi^+Ayj^+Azk^At point B;…

Q: 4-98. Replace the force system by an equivalent resultant force and couple moment at point P. y 455…

Q: *4-128. Determine the magnitudes of FA and FB So that the resultant force passes through point O of…

A: GIVEN DATA- A COLUMN LOADED WITH SYSTEM OF FORCES WE HAVE TO FIND FORCE FA AND FB

Q: 4-57. Determine the magnitude of the moment that the force F exerts about the y axis of the shaft.…

Q: *4-48. The pipe of weight Wis to be pulled up the inclined plane of slope a using a force P. If…

A: Given: The weight of the pipe is W. Here P is the pulling force, N is the normal force and F is…

Q: 4-17 If rope BC will fail when the tension becomes 50 kN, determine the greatest vertical load F…

Q: 4-130. The building slab is subjected to four parallel column loadings. Determine the equivalent…

Q: F4-6. Determine the reactions at the smooth contact points A, B, and C on the bar. 250 N 307 015 m…

A: Given Applied load 250 N Structure To find Reaction at point A, B and C

Q: 4-28. The tower crane is used to hoist a 2-Mg lo at constant velocity. The 1.5-Mg jib BD and 0.5-Mg…

A: Drawing the free body diagram of the tower crane,

Q: 4-87. Determine the required magnitude of force F, if the resultant couple moment on the beam is to…

A: Find the force F

Q: 4-6. The crowbar is subjected to a vertical force of P = 25 lb at the grip, whereas it takes a force…

A: Given Data The vertical force acting on the crowbar is: P=25 lb The force acting on the nail is:…

Q: 4-121. Replace the loading on the frame by a single resultant force. Specify where its line of…

A: To find: The line of action intersect a horizontal line along the member CB, measured from the end…

Q: *4-4. The A-36 steel rod is subjected to the loading shown. If the cross-sectional area of the rod…

Q: 4-155. Replace the distributed loading by an equivalent resultant force and specify where its line…

Q: R3-1. The boom has a length of 9 m, a weight of 4 kN, and mass center at G. If the maximum moment…

A: Given: L= 9 m Wb= 4kN Moment developed by motor (M)= 30 kN.m To determine: The maximum load (W) that…

Q: F4-22. Determine the couple moment acting on the beam.

A: Determine the couple moment acting of the beam.

Q: P4-3. write the moment equations about the I, y, and z axes. 600 N 400 N 300 N в -3 m в.

A: The moment equation about the x axis can be determined as,

Q: F4-12. Determine the components of reaction that the thrust bearing A and cable BC exert on the bar.…

A: Given Data: The load acting on the member is 80 N. The free-body diagram of the member can be…

Q: 4-15. The 10-kg uniform rod is pinned at end A. If it is subjected to a couple moment of 50 N-m,…

A: Given data: Mass of uniform rod = 10 kg Magnitude of couple applied = 50 N m…

Q: 4-21. The uniform beam has a weight Wand length / and is supported by a pin at A and a cable BC.…

A: Consider the free body diagram shown below for the beam. Here, W is the weight of the beam.

Q: *3-40. Determine the magnitude of force F in cable AB in order to produce a moment of 750 N. m about…

A: Given: 1.2 m = 4 ft 1.8 m = 6 ft 750 N.m = 553 lb-ft Coordinates of AB and CD:

Q: 4-143. Replace this loading by an equivalent resultant force and specify its location, measured from…

A: Let R be the equivalent resultant force and x be the distance of this resultant force from point O.…

Q: 4-143. Replace this loading by an equivalent resultant force and specify its location, measured from…

Question

4-14. The connected bar BC is used to increase the lever
arm of the crescent wrench as shown. If a clockwise moment
of MA
120 N.
•m is needed to tighten the nut at A and the
%3D
extension d = 300 mm, determine the required force F in
order to develop this moment.
%3D
d
15
30
300 mm
A
Probs. 4-13/14

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

4-105 - The overhead transmission shaft AE is driven at a constant speedby an electric motor connected by a flat belt to pulley B. Pulley Cmay be used to drive a machine tool located directly below C,while pulley D drives a parallel shaft located at the same height asAE. Knowing that TB + TB' = 162 N, TC = 180 N, TC' = 72 N, TD = 0 and TD' = 0, determine:(a) the tension in each portion of thebelt driving pulley B(b) the reactions at the bearings A and Ecaused by the tension in the belts.
The magnitude of the moment of the force F=300i-200j+600k N about the y-axis is. Select one: a. 240 [N.m] b. 20 [N.m] c. -240 [N.m] d. -20 [N.m]
Which of the following gives the moment MD about point D of the tensile force TBA exerted by the wire at point B? Note that rB/D = (4i - 6k) m and TBA = (-8i + 6j + 4k) kN and that MD = rB/D x TBA. a. (36.0i + 32.0j + 24.0k) kN-mb. (48.0i + 24.0j + 16.0k) kN-mc. (-36.0i - 32.0j - 24.0k) kN-md. (16.0i - 12.0j -8.0k) kN-m
Determine the magnitude of the pin force at A.Assume W = 755 lb, a = 5.4 ft, b = 3.9 ft, r = 7 in.
7-12 Rod AB is fixed to a smooth collar D, which slides freely along the vertical guide. Determine the normal force, shear force, and moment at point C, which is located just to the left of the 60 lb concentrated load
The jib crane supports a load of 750 lb from the trolly which rides on the top of the jib. Determine theinternal normal force, shear force and moment in the column at point D when the trolley is at the positionshown in figure 8. The crane members are pinned together at B, E and F and supported by a short link BH.
4-61 Change the force F to {200i + 400j -700k}
How much work is done by the force in the spring when the slender rod rotates clockwise about the fixed pin support at O from the vertical position (where AB is horizontal) to the horizontal position? The spring has a stiffness of k = 125 N/m and an unstretched length of 0.15 m. Take d1= 0.29 m and d2= 0.85 m. Choose the correct answer. a) 94.9 Joule b) 99.9 Joule c) -99.9 Joule d) 0 Joule e) -94.9 Joule
Show FBD and complete solution. The pin spanner is used to turn shafts and collars. If a moment of is required to turn the 200-mmdiameter collar about its center O under the action of the applied force P, determine the contact force R on the smooth surface at A. Engagement of the pin at B may be considered to occur at the periphery of the collar.
Determine the magnitude of the moment reaction. Take the angle a = 77 °, b = 47 ° and F = 283N
The cylinder has a mass of 30 kg and is mounted on an axle that is supported by bearings at A and B. If the axle is turning at 40 rad/s (direction see figure) determine the vertical components of force acting at the bearings at this instant
4-20