4- Refer to Figure below. If Hj=3 ft, H2=4.5 ft, h=1.5 ft, ysai=118.9 lb/ft', area of the tank=6.25 ft', and hydraulicconductivity of the sand (k)=5.3x10-³ ft/sec,What is the rate of upward seepage of water (ft'/min)?b. If the point C is located at the middle of the soil layer, then what is the effective stress at C?а.(孟)Valve (open)Inflow不

Answered: Image /qna-images/answer/082750e6-0860-46e3-bbad-57d02d93abd0.jpg

4- Refer to Figure below. If H1=3 ft, H2=4.5 ft, h=1.5 ft, ysa=118.9 lb/ft³, area of the tank=6.25 ft², and hydraulic conductivity of the sand (k)=5.3X10-³ ft/sec, a. What is the rate of upward seepage of water (ft/min)? b. If the point C is located at the middle of the soil layer, then what is the effective stress at C? H2 Valve (open) Inflow

4- Refer to Figure below. If H1=3 ft, H2=4.5 ft, h=1.5 ft, ysa=118.9 lb/ft³, area of the tank=6.25 ft², and hydraulic conductivity of the sand (k)=5.3X10-³ ft/sec, a. What is the rate of upward seepage of water (ft/min)? b. If the point C is located at the middle of the soil layer, then what is the effective stress at C? H2 Valve (open) Inflow

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter8: Stresses In A Soil Mass

Section: Chapter Questions

Problem 8.14P

See similar textbooks

Similar questions

Refer to Problem 8.4. Using the flow net drawn, calculate the hydraulic uplift force at the base of the hydraulic structure per meter length (measured along the axis of the structure).8.24 For the hydraulic structure shown in Figure 8.24, draw a flow net for flow through the permeable layer and calculate the seepage loss in m3/day/m.
Use 10 kN/m3 for unit weight of water. For a concrete structure that retains water, a flow net is sketched as shown in Figure H8-3. Noting the marked location of the Datum, answer the following: Mark on the figure all boundary Also mark the type of each boundary. Calculate the uplift pressures at points A, B, C, D, E, and F. Calculate the factor of safety against The seepage loss (q) per day per meter length of the (i.e. q in m3/day/m) if the permeability of the soil is k = 10-4 m/sec.
Given: velocity of flow = 0.0375 m/s coefficient =0.05 m/s porosity p =48% slope S = 3/4 The soil porosity in the area where the 46-cm diameter well is 48%, find the discharge of the groundwater. Given the coefficient =0.05 m/s and porosity p =48%, find the transmissibility (T) in m/s per unit m, if the aquifer width is 1.2 m. Given the discharge Q get in Question #1, transmissibility T in Question#2, slope S = 3/4; find the aquifer width X.
From the figure shown, H1 = 0.60, H2 = 0.90 m. and h = 0.45 m. The sad has a saturated unit weight of 18.65 kN/m3 . Hydraulic conductivity of sand K = 0.12 cm/sec. If the cross sectional area of tank = 0.46 m2 , determine the following: 1. Total stress and Effective stress at C. 2. Pore water pressure at C. 3. Rate of upward seepage of water in liters/sec.
For the two-dimensional flow system shown below (units in meters):Compute the total flow rate under the Dam. X = 4, Y = 8. Note 1: Point A is located in the middle point of the equipotential lines. Point B is located in the middle point of the flow lines.Note 2: Assume e=0.8 (void ratio) and k=10^-3 cm/s (coeff. of permeability).Note 3: Datum is located at the bottom level of the water (right side of Dam).Note 4: Remember, the figure is drawn to scale. So, use the value of 2X+Y to estimate any dimension that you consider necessary.
Refer to Figure 7.24. The following data were collected during the field permeability measurement of a confined aquifer using a pumping test. Determine the hydraulic conductivity of the permeable layer. Use Eq. (7.49). Thickness of the aquifer, H = 4.5 m Piezometric level and radial distance of the first observation well: h1 = 2.9 m; r1 = 17.8 m Piezometric level and radial distance of the second observation well: h2 = 1.8 m; r2 = 8.1 m Rate of discharge from pumping, q = 0.5 m3/min
trench 80 ft long is excavated 500 ft away and is parallel to a riverbank. A sand aquifer is 40 ft thick The river water surface is 50 ft above the horizontal bottom of the aquifer. If the water depth in the trench must be maintained at 10ft, at what rate must water be pumped from the trench? How far from the trench will the aquifer cease to be saturated? Use K of sand = 30 ft/day
L = 370 mm A = 145 cm^2 h = 340 mm Water collected in 3 min Q = 580 cm^3 Void ratio of sand e= 0.66 Determine the Hydraulic conductivity and seepage velocity.
Find the rate of flow in m^3/sec/m (at right angles to the cross-section shown in Figure 7.33) through the permeable soil layer. Given: H 4 m, H1 2 m, h 2.75 m, S 30 m, a 14°, and k 0.075 cm/sec.
9. From the figure shown: (See picture below) Cross-sectional area = 0.6m2 Hydraulic Conductivity of sand = 0.1 cm/sec What is the rate of upward seepage of water? (Answer: 360 cm3/sec) What would be the critical hydraulic gradient? (Answer: 1.12 m) What value of h to cause boiling? (Answer: 2.8 m)
Given the coefficient k =0.05 m/s and porosity p = 48%, find thetransmissibility (T) in m/s per unit m, if the aquifer width is 1.2 m.Formula: - It is the flow rate per day thru a unit areaunder a unit hydraulic gradient For an aquifer with thickness, Band width, X:T = K*B and Ag = BXThus: Q = (T*X*S)
Refer to the figure. If H1 = 1.94 m, H2 = 2.37 m, h = 1.c m, e =0.49, Gs = 2.67,area of the tank = 0.64 m2, and hydraulic conductivity of the sand (k) = 0.3d cm/sec. What is the upward seepage force per unit volume of soil?