Will upvote if answered in 10-15 mins 4. A 1.2 kg quarter circular plate with 0.20 m radius is welded to a1.5-kg triangular plate to form the composite thin plate as shown.Which of the following best approximates the mass moment ofinertia of the composite thin plate with respect to the y-axis?r = 0.20 my0.0520 kg-m^20.1002 kg-m^20.20 mNote: The mass moment of inertia of a triangular plate with respectto one of its bases is mb² where m is the mass of the plate and bis the length of the leg perpendicular to the base where the massmoment of inertia is required.0.0468 kg-m^20.0220 kg-m^20.20 m0.40 m

The mass of the quarter circle,(m1)=1.2 kg The radius of the quarter circle,(R)=0.20 m The mass of…

4. A 1.2 kg quarter circular plate with 0.20 m radius is welded to a 1.5-kg triangular plate to form the composite thin plate as shown. Which of the following best approximates the mass moment of inertia of the composite thin plate with respect to the y-axis? r = 0.20 m

4. A 1.2 kg quarter circular plate with 0.20 m radius is welded to a 1.5-kg triangular plate to form the composite thin plate as shown. Which of the following best approximates the mass moment of inertia of the composite thin plate with respect to the y-axis? r = 0.20 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A small block of mass m slides frictionlessly in the given orbit. Calculate the magnitude of the…

A: According to the given data m=1kg g=10m/s2 We need to find Resultant forces the block at C

Q: For the given isometric drawing, draw the corresponding top, front and right side views

A: According to the given data A isometric view of a object We need to draw The corresponding top,…

Q: 2. Calculate Passive House's energy demand. a, Calculate window U-value based on given data in…

A: Given: To find: U value of window Power needed

Q: 0.2 m 0.25 m 0.2m 06m Knowing that at the instant shown the angular velocity of rod AB is 15 rad/s…

A: As per Bartleby answering guidelines, one question can be answered if multiple questions are posted.…

Q: The wedge shaped bar shown in Figure Q1 is to be analysed using a single one dimensional quadratic…

A: Given data: a) Calculate the strain shape function matrix. [B], for the element.b) Using the strain…

Q: u have a 10-mm steel drill rod that we then heat-treated and ground. The measured hardness was found…

A: Given: d=10 mmHB=290 Solution: Ultimate tensile strength is calculated as; Sut=3.4HB=3.4×290=986 MPa…

Q: Question #5: Replace the distributed-load-below-by-a-single-force. Note the magnitude, position, and…

Q: A pair of helical gears are machined with a hob. The hob has a 20 degree pressure angle and machines…

A: The pressure angle = 20 degrees The circular pitch, p = 0.55 in/tooth the number of teeth on pinion,…

Q: For the circular shaft (G=12×106 psi) shown below: a. Compute the reaction torque and draw the…

Q: Both slip and twinning account for plastic deformation. However, the two phenomena occur by…

A: Given data:- Slip:-Slip is a type of deformation that happens in crystalline materials like metals…

Q: A large steel plate (1.0% carbon) 5.0 cm thick is initially at a temperature of 425 °C. It is…

A: The centerline temperature and the temperature at 1.25 cm from the surface. Given: The thickness of…

Q: 10. Water flows from a lake as shown below at a rate of 5.0 ft³/s. Is the device inside the building…

Q: An oil with (s.g=0.85) and kinematic viscosity = 1.8x105 m²/s flows in a 10-cm diameter pipe at…

Q: the ground and free in the upper end. a) Calculate the compressive stress, then the minimum…

A: Given Data: H=3 mm=1000 kgFOS=3σut,c=241 MPaE=190 GPa To Find: (a) The compressive stress. (b) The…

Q: The ball at A in (Eigure 1) is kicked such that 0 = 55°. It strikes the ground at B having…

Q: Consider two concentric spheres of radii R1 and R2 (R1<R2). The inner sphere has a temperature of…

A: The inner sphere has a temperature T1=20°C. The outer sphere has a temperature T2=100°C The thermal…

Q: Explain the operating principles and limitations of 3 viscosity measuring devices

A: The operating principles and limitations of 3 viscosity measuring devices

Q: We have two connected tanks with surface areas A1 and A2, both open to the atmosphere, filled with…

A: h1=Height between point 1 to the bottom in left tankd=Height between point 2 to the bottom in right…

Q: A rope of length L = 1.5 m and mass m = 2.3 kg is initially at rest and can slide on an inclined…

A: The maximum value of b. Given: The length of the rope is L=1.5 m. The mass of the rope is m=2.3 kg.…

Q: Consider the following one-dimensional, steady-state heat con- duction problem d²T(x) 1 dx² +80=0 in…

A: Given: To find: Finite difference formulation Node temperatures Compare numerical and exact…

Q: 4. During a cold winter day, wind blows parallel to a 4 m high and 10 m long wall of a house. If the…

A: Given: The height of wall is h=4 m The length of wall is L=10 m The temperature of air is T∞=5°C.…

Q: F 45 4 PROB. 3-35. T 3-35. The crank Q₂B is rotating clockwise at 5 rpm. Q,B= 1.5 in.; BC= 3 in.;…

A: The speed of crank Q2B is 5 rpm (CW). The lengths are Q2B=1.5 in, BC=3 in, CD=0.5 in The diameter of…

Q: Give two (2) examples of light vehicle automatic transmission and driveline system faults chosen…

A: Given Data and to find: 2 examples of each.

Q: Forces are accepted as acting at the centre of pressure of submerged surfaces. Describe the…

A: This question is based on the concept of centre of pressure from fluid mechanics.

Q: Please provide more details for question b and c. thank you

A: For selecting a point of operation: We take the characteristic line of our suitable pump and select…

Q: Develop a mathematical model of the performance of a plastic bonding process given the process data…

A: To develop a mathematical model for the plastic bonding process, we need to relate the input…

Q: Consider the following transient heat conduction problem 10T ²T 2²T a dt дҳ2 Əy² -= T=0 T = 100 T=0…

A: Since this is multiple question, we will solve the first one kindly post the other part separately.…

Q: a: Draw the P-v diagrams for the three power cycles and label each process: Diesel, Stirling, and…

Q: Collar A (mA = 2 kg) and Collar B (mB = 2 kg) each slide with negligible friction along a rod. A…

A: Given data is shown below. mA=2 kgmB=2 kgk=100 N/mx0=250 mm To determine:- a) velocity of collar A…

Q: A particle of mass m = 1 kg arrives at point O with a horizontal velocity vo and starts rolling do a…

A: Given: m=3 kgR=5 mk=60 N/m

Q: For F = 51 lb, compute the combined moment of the two forces about (a) point O, (b) point C, (c)…

A: Given Data

Q: ● Determine the moments and products of inertia of the bent rod shown (composed of three slender…

A: The moments and products of inertia are quantities used to describe the distribution of mass in an…

Q: During the execution of a reversible non flow process the work Is -156.2 KJ. If V1 =0.845 cubic…

A: Given data as below: Work W = -156.2 KJ Volume V1 = 0.845 m3 Pressure P = -730V + 690 KPa To…

Q: 4.33 through 4.45 Determine the forces in the members identi- fied by "x" of the truss shown by the…

Q: Determine the normal stress that acts at point B.

A: The rod diameter d =40 mm = 0.04m The force system Fx= 1390N Fy= 510N Fz= 835N Find a) The Normal…

Q: The position with time of an object is given by x(t)=Acos(ωt) If the amplitude is 1.58 m, and the…

A: According to the given data The position with time of an object is given byx(t)=Acos(ωt) A=1.58 m…

Q: (6) For an aluminum alloy under constant load, the creep rate increased by a factor of 2 when the…

Q: A supersonic projectile pushing gas ahead in tube filled with initially still air at 294K and…

A: Given: upstream pressure = 101.3 kPa upstream temperature = 294 K downstream pressure = 608 kPa To…

Q: A liquid is placed inside a chamber and its pressure is 1,546 MPa and its volume is 1.6 m3. After a…

A: The initial pressure,(Pi)=1546 MPa The initial volume,(Vi)=1.6 m3 The final pressure,(Pf)=2019 MPa…

Q: Pumps: A centrifugal pump having 4 stages in parallel, delivers 18 kiloliters/min of liquid…

Q: What should be the percent increase of COP of a standard vapor compression refrigeration system when…

Q: Assuming that link 2 is the input, write the vector loop equation indicating the fixed constants…

A: Please refer handwritten solution

Q: Q3/ Answer the following question: A turbocharged, 4 cylinders and 2 liters engine operates with…

A: The number of cylinder, k = 4 The volume of the cylinder, V = 2 liters The speed of the engine, N =…

Q: 03: A refrigerator working on Carnot cycle uses R134a as the working fluid. The refrigerant changes…

Q: Given the following measurements of velocity for a falling object with m = 3kg: v, meters/seconds t,…

A: It is asked to approximate the drag coefficient using 4th order Runge-Kutta method Alos find the…

Q: Homework:- 1- The amplitude of vibration of an undamped system is measured to be (1 mm). The phase…

A: Given data: The amplitude of the vibration is, A=1 mm. The phase shift is, ϕ=2 rad. The time taken…

Q: A 15,500 kg jet plane takes off from an aircraft carrier with the help of a catapult (see figure a).…

Q: 5) Consider the linear system described by the following differential equation: * + 2ax + (a²+4)x=…

A: Given Data: x..+2ax.+a2+4x=F(t)F(t)=δ(t) To Find: (a) Transfer function. (b) Unit impulse…

Q: The e wheel has a mass of 100 kg and a radius of gyration of ko = 0.2 m. A motor supplies a torque M…

A: Mass of wheel, mw=100 kgRadius of gyration, k0=0.2 mTorque, M=40θ+900 NmDistance travelled, s=2…

Q: 15. Determine the friction force if = 0.3 and M = 0.2. (A) 170 N (B) 191 N (C) 850 N (D) 294 N 300 N…

Question

Will upvote if answered in 10-15 mins

4. A 1.2 kg quarter circular plate with 0.20 m radius is welded to a
1.5-kg triangular plate to form the composite thin plate as shown.
Which of the following best approximates the mass moment of
inertia of the composite thin plate with respect to the y-axis?
r = 0.20 m
y
0.0520 kg-m^2
0.1002 kg-m^2
0.20 m
Note: The mass moment of inertia of a triangular plate with respect
to one of its bases is mb² where m is the mass of the plate and b
is the length of the leg perpendicular to the base where the mass
moment of inertia is required.
0.0468 kg-m^2
0.0220 kg-m^2
0.20 m
0.40 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data.

VIEW

Step 2: Calculations for the mass moment of inertia.

VIEW

Solution

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A thin rectangular plate is welded on the center of the top of a circular cylinder. The mass of the cylinder is 5kg and the mass of the triangular plate is 2kg. Note that the x-axis is located on the centroid of the cylinder. Which of the following is closest to the moment of inertia of the composite object about the x-axis?a. 0.712kgm^2b.0.473 kgm^2c.0.1074 kgm^2d. 0.0401 kgm^2Which of the following is closest to the radius of gyration of the composite object about the x-axis?a. 1238 mb. 0.0757 mc. 0.260 md. 0.319
(a) Show that the polar radius of gyration rO of the annular area shown is approximately equal to the mean radius Rm = (R1 + R2)/2 for small values of the thickness t = R2 – R1. (b) Determine the percentage error introduced by using Rm in place of rO for the following values of t/Rm: 1, 1/2, and 1/10.
A turbine rotor is mounted on a stepped shaft that is fixed at both ends as shown in The torsional stiffnesses of the two segments of the shaft are given by ka = 3,000 N-m/rad and ka = 4.000 N-m/rad. The turbine generates a harmonic torque given by M(t) = M, cos at about the shaft axis with M, = 200 N-m and e = 500 rad/s. The mass moment of inertia of the rotor about the shaft axis is Jo = 0.05 kg-m. Assuming the equivalent torsional damping constant of the system as e, = 2.5 N-m-s/rad, determine the steady-state response of the rotor, )
The total mass of the Baja car and driver, including the wheels, is 250 kg. Each pair of 58-cm radius wheels and the axle has a total mass of 20 kg and a mass moment of inertia of 2.9 kg·m2 . The center of gravity of the driver and Baja body (not including the wheels) is located x = 0.70 m from the rear axle A and y = 0.55 m from the ground. The wheelbase is L = 1.60 m. If the engine exerts a torque of 500 N·m on the rear axle, what is the car’s acceleration?
The density of the material is 7.85 Mg / m3. (Figure 1) Determine the mass moment of inertia of the assembly about the z axis. Express your answer to three significant figures and include the appropriate units.
Two identical solid spheres are attached on the 2cm diameter solid rod with the density of 7750 'kg/m³. Calculate moment inertia about P- P axis of a lamina. The measurements are in cm. 3 kg 5 kg 10 cm 50 cm 40 cm
A truck with four wheels, each 750 mm diameter, travels on rails round a curve of 75 m at a speed of 50 km/h. The total mass of the truck is 5 t and its centre of gravity is midway between the axles, 1.05 m above the rails and midway between them. Each pair of wheels is driven by a motor rotating in the opposite direction to the wheels and at four times the speed. The moment of inertia of each pair of wheels is 15 Kgm2. The rails lie on a horizontal plane and 1.45 m apart. Determine the load on each rail.
Locate the center of mass z¯ of the assembly. The assembly consists of a cylindrical center core, A , having a density of 8.10 Mg/m3 , and a cylindrical outer part, B , and a cone cap, C , each having a density of 3.50 Mg/m3 . (Figure 1) Express your answer to three significant figures and include the appropriate units.
For a thin, circular ring, what is its mass moment of inertia? Is it Ixx = Iyy = (mr^2)/4, and Izz = (mr^2)/2? Also, if I have integral(dm), for this ring will dm = (m/(2*pi*r)) * (r*dtheta). Let me know if I am wrong.
need asap pls Determine the mass moment of inertia of steel balls used in ball bearings. Use a diameter of 2 cm.
A caravan weighs 28 kN. It has a wheel base of 2 m, track width 1m and height ofC.G. 300 mm above the ground level and lies midway between the front andrear axle. The engine flywheel rotates at 2950 rpm clockwise when viewed from thefront. The moment of inertia of the flywheel is 4 kg-m 2 and moment of inertia ofeach wheel is 3 kg-m 2 . Find the reactions between the wheels and the ground whenthe car takes a curve of 15 m radius towards right at 30 km/h, taking intoconsideration the gyroscopic and the centrifugal effects. Each wheel radius is 400 mm.
A yoyo is constructed by attaching three uniform, solid disks along their central axes as shown. The two outer disks are identical, each with mass M = 58 g, radius R = 3.3 cm, and moment of inertia 1/2MR2. The central, smaller disk has mass M/2 and radius R/2. A light, flexible string of negligible mass is wrapped counterclockwise around the central disk of the yoyo. The yoyo is then placed on a horizontal tabletop and the string is gently pulled with a constant force F = 0.25 N. The tension in the string is not sufficient to cause the yoyo to leave the tabletop. In this problem consider the two cases show. In Case 1 the string is pulled straight up, perpendicular to the tabletop. In Case 2 the string is pulled horizontally, parallel to the tabletop. In both cases the yoyo rolls without slipping. In both the cases shown what is the magnitude of the tourqe t excerted by the string about the contact point of the yo-yo wiith the table in N*m. What is the moment of intertia of the yo-yo…