Give two (2) examples of light vehicle automatic transmission and driveline system faults chosen from electronically controlled automatic transmissions ● • continuously variable transmissions ● (CVTs) • constant velocity joints Hookes-type joints • rear wheel drive shafts • rear wheel drive final drives ● • front wheel drive final drives for each of the following: (5 - 10 words each) a. Intermittent faults b. Multi-system faults. c. Introduced as a result of a system repair d. Indirect, caused by the influence of external systems

Give two (2) examples of light vehicle automatic transmission and driveline system faults chosen from electronically controlled automatic transmissions ● • continuously variable transmissions ● (CVTs) • constant velocity joints Hookes-type joints • rear wheel drive shafts • rear wheel drive final drives ● • front wheel drive final drives for each of the following: (5 - 10 words each) a. Intermittent faults b. Multi-system faults. c. Introduced as a result of a system repair d. Indirect, caused by the influence of external systems

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

pls explain and show to me the DIAGRAM OF OPEN DIFFERENTIAL IN ROLLER BEARINGS thanks
pleassssse solve question 8, statics
Problem Solving. Solve the following problems completely. 5. Motors from two different manufacturers are being considered for application.Both motors are 50Hp, 460 volts, 3 phase, 60 cycles. Motor A operates at 80%efficiency and motor B operates at 89% efficiency. The expected need for themotor is 15 years. Motor A cost P120, 000.00 and motor B P150, 000.00.Electrical energy cost P8.00 per Kw-Hr and the motors will be operating 8 hoursper day, 250 days a year. Assume taxes and insurance are 3% of first cost. Whichmotor should be purchased?
A NC machine tool table is powered by a servomotor, lead screw, and optical encoder. The lead screw has a pitch = 5.0 mm and is connected to the motor shaft with a gear ratio of 16:1 (16 turns of the motor for each turn of the lead screw). The optical encoder is connected directly to the lead screw and generates 200 pulses/rev of the lead screw. The table must move a distance = 100 mm at a feed rate = 500 mm/min. Determine (a) the pulse count received by the control system to verify that the table has moved exactly 100 mm; and (b) the pulse rate and (c) motor speed that correspond to the feed rate of 500 mm/min. Solve the problem assuming the optical encoder is directly coupled to the motor shaft rather than to the lead screw.
ass 4. vib . Give detailed description of at least two methods of vibration control.
Automobile manufacturers specify a certain number of miles at which the engine timing belt should be replaced. Is this an example of a “safe-life”-designed component or a “fail-safe”-designed component? What are the implications for the condition of the timing belt when it is removed?
the figure shows a motor driving a two-output transmission system. The blower requires a certain amount of force to operate since the drum rotates at an angular acceleration of 0.03 rad/s2. Determine the torque produced by a motor with a torque of 700 Nm and a speed of 1,600 rpm. following:- The power produced at the drum (P). The torque requirement for the blower to operate (Tblower) and power generation (Pblower) The overall efficiency transmission of the gear system, hO. If the speed of motor is NOT given, explain without calculation how the overall efficiency transmission of the gear system can be obtained. Given:- Number of gear teeth, t:- t1=40 ; t2=200 ; t3=50 ; t4=200 ; t5=40 ; t6=120 ; t7=60 and t8=120 Equivalent mass moment of inertia, Ieq:- Imotor,5=25 kgm2 ; I23=10 kgm2 ; Iblower,4=15 kgm2 ; I67=20 kgm2 and Idrum,8=60 kgm2 Friction torque in bearing, Fb:- A=F=25 Nm ; I=J =20 Nm ; B=C=G=H=5 Nm and D=E=10 Nm Efficiency of all gear mesh, ⴄ=85%
what factors determine the design of the power transmission mechanisms in a rear wheel drive van (Diesel) and how do you calculate power and torque at the driveshaft, assuming the following: its 5 speed transmission, Gear system efficiency is 88% Gear ratios: 1 st: 4.17:1 2 nd 2.34:1 3 rd 1.52:1 4 th 1.14:1 and power and torque to be calculated at the point where engine is generating its maximum power
A CNC machine tool table is powered by a servomotor, ball screw, and optical encoder. The ball screw has a pitch = 7.5 mm and is connected to the motor shaft with a gear ratio of 12:1. The optical encoder is connected to the ball screw and generates 200 pulses/rev of the screw. The table must move a distance of 300 mm at a feed rate = 450 mm/min. (a) Determine the pulse count received by the control system to verify that the table has moved exactly 300 mm. Also, what are (b) the pulse rate and (c) motor speed that corresponds to the specified feed rate?
Assume that you are to design a 3V V-belt drive. Given that input speed as 1750 rpm and nominal output speed as 725 rpm. Starting with belt linear velocity 4000 ft/min, specify the output sheeve D2 once you specify D1 from last question. D2 = ___ in. Provide write down steps including equations. *** 21.07 and 21.1 were marked incorrect
The client requires a single step-up spur gearbox to transmit a 10 kW Power from a shaft rotating at 1000 rpm, while output speed must be 1700 rpm. The material of the gear and pinion 817M40 and 655M13, respectively. Use table 6.10 on page 128 to collect suitable gear and pinion. 1.1 briefly state the problem 1.2 State the design specification considering the following design factors a) Functionality b) stress 1.3 State formula and standards relevant to the single step-up spur gearbox design. 1.4 If the pinion has 24 teeth, use the Lewis formula to determine the face width of the pinion and gear. Then, do one set of the calculations and tabulate the answers. 1.5 conclusion
Based on the pic attached, If component B of #6 is changed to 3 parallel components and each has thesame reliability, what is the system reliability now? pls provide celaar solutions detailed thanks